#include <Copyright.h>

/********************************************************************************
* gtSimRegs.h
*
* DESCRIPTION:
*       This file includes the declaration of the struct to hold the addresses
*       of switch (global & per-port).
*
* DEPENDENCIES:
*       QuarterDeck register MAP.
*
* FILE REVISION NUMBER:
*
*******************************************************************************/

#ifndef __qdSimRegsh
#define __qdSimRegsh

/* QuarterDeck Per Port Registers */
#define QD_REG_PORT_STATUS        0x0
#define QD_REG_SWITCH_ID        0x3
#define QD_REG_PORT_CONTROL        0x4
#define QD_REG_PORT_VLAN_MAP    0x6
#define QD_REG_PVID                0x7
#define QD_REG_RATE_CTRL        0xA
#define QD_REG_PAV                0xB
#define QD_REG_RXCOUNTER        0x10
#define QD_REG_TXCOUNTER        0x11
#define QD_REG_Q_COUNTER        0x1B

/* QuarterDeck Global Registers */
#define QD_REG_GLOBAL_STATUS    0x0
#define QD_REG_MACADDR_01        0x1
#define QD_REG_MACADDR_23        0x2
#define QD_REG_MACADDR_45        0x3
#define QD_REG_GLOBAL_CONTROL    0x4

/* the following VTU entries are added for Fullsail and Clippership */
#define QD_REG_VTU_OPERATION        0x5
#define QD_REG_VTU_VID_REG        0x6
#define QD_REG_VTU_DATA1_REG        0x7
#define QD_REG_VTU_DATA2_REG        0x8
#define QD_REG_VTU_DATA3_REG        0x9
#define QD_REG_STATS_OPERATION        0x1D
#define QD_REG_STATS_COUNTER3_2        0x1E
#define QD_REG_STATS_COUNTER1_0        0x1F

#define QD_REG_ATU_CONTROL        0xA
#define QD_REG_ATU_OPERATION    0xB
#define QD_REG_ATU_DATA_REG        0xC
#define QD_REG_ATU_MAC_BASE        0xD
#define QD_REG_ATU_MAC_01        0xD
#define QD_REG_ATU_MAC_23        0xE
#define QD_REG_ATU_MAC_45        0xF
#define QD_REG_IP_PRI_BASE        0x10
#define QD_REG_IP_PRI_REG0        0x10
#define QD_REG_IP_PRI_REG1        0x11
#define QD_REG_IP_PRI_REG2        0x12
#define QD_REG_IP_PRI_REG3        0x13
#define QD_REG_IP_PRI_REG4        0x14
#define QD_REG_IP_PRI_REG5        0x15
#define QD_REG_IP_PRI_REG6        0x16
#define QD_REG_IP_PRI_REG7        0x17
#define QD_REG_IEEE_PRI            0x18

/* Definition for QD_REG_PORT_STATUS */
#define QD_PORT_STATUS_DUPLEX    0x200

/* Definitions for MIB Counter */
#define GT_STATS_NO_OP            0x0
#define GT_STATS_FLUSH_ALL        0x1
#define GT_STATS_FLUSH_PORT        0x2
#define GT_STATS_READ_COUNTER        0x4
#define GT_STATS_CAPTURE_PORT        0x5
#define GT_STATS_CAPTURE_PORT_CLEAR  0x6  /* RMU page 2 */

#define QD_PHY_CONTROL_REG                0
#define QD_PHY_AUTONEGO_AD_REG            4
#define QD_PHY_NEXTPAGE_TX_REG            7
#define QD_PHY_SPEC_CONTROL_REG            16
#define QD_PHY_INT_ENABLE_REG            18
#define QD_PHY_INT_STATUS_REG            19
#define QD_PHY_INT_PORT_SUMMARY_REG        20

/* Bit Definition for QD_PHY_CONTROL_REG */
#define QD_PHY_RESET            0x8000
#define QD_PHY_LOOPBACK            0x4000
#define QD_PHY_SPEED            0x2000
#define QD_PHY_AUTONEGO            0x1000
#define QD_PHY_POWER            0x800
#define QD_PHY_ISOLATE            0x400
#define QD_PHY_RESTART_AUTONEGO        0x200
#define QD_PHY_DUPLEX            0x100

#define QD_PHY_POWER_BIT                11
#define QD_PHY_RESTART_AUTONEGO_BIT        9

/* Bit Definition for QD_PHY_AUTONEGO_AD_REG */
#define QD_PHY_NEXTPAGE            0x8000
#define QD_PHY_REMOTEFAULT        0x4000
#define QD_PHY_PAUSE            0x400
#define QD_PHY_100_FULL            0x100
#define QD_PHY_100_HALF            0x80
#define QD_PHY_10_FULL            0x40
#define QD_PHY_10_HALF            0x20

#define QD_PHY_MODE_AUTO_AUTO    (QD_PHY_100_FULL | QD_PHY_100_HALF | QD_PHY_10_FULL | QD_PHY_10_HALF)
#define QD_PHY_MODE_100_AUTO    (QD_PHY_100_FULL | QD_PHY_100_HALF)
#define QD_PHY_MODE_10_AUTO        (QD_PHY_10_FULL | QD_PHY_10_HALF)
#define QD_PHY_MODE_AUTO_FULL    (QD_PHY_100_FULL | QD_PHY_10_FULL)
#define QD_PHY_MODE_AUTO_HALF    (QD_PHY_100_HALF | QD_PHY_10_HALF)

#define QD_PHY_MODE_100_FULL    QD_PHY_100_FULL
#define QD_PHY_MODE_100_HALF    QD_PHY_100_HALF
#define QD_PHY_MODE_10_FULL        QD_PHY_10_FULL
#define QD_PHY_MODE_10_HALF        QD_PHY_10_HALF

/* Bit definition for QD_PHY_INT_ENABLE_REG */
#define QD_PHY_INT_SPEED_CHANGED        0x4000
#define QD_PHY_INT_DUPLEX_CHANGED        0x2000
#define QD_PHY_INT_PAGE_RECEIVED        0x1000
#define QD_PHY_INT_AUTO_NEG_COMPLETED        0x800
#define QD_PHY_INT_LINK_STATUS_CHANGED        0x400
#define QD_PHY_INT_SYMBOL_ERROR            0x200
#define QD_PHY_INT_FALSE_CARRIER        0x100
#define QD_PHY_INT_FIFO_FLOW            0x80
#define QD_PHY_INT_CROSSOVER_CHANGED        0x40
#define QD_PHY_INT_POLARITY_CHANGED        0x2
#define QD_PHY_INT_JABBER            0x1

#endif /* __qdSimRegsh */