#include <Copyright.h>

/********************************************************************************
* gtPhyCtrl.h
*
* DESCRIPTION:
* API definitions for PHY control facility.
*
* DEPENDENCIES:
* None.
*
* FILE REVISION NUMBER:
* $Revision: 10 $
*******************************************************************************/

#include <msApi.h>
#include <gtHwCntl.h>
#include <gtDrvConfig.h>
#include <gtDrvSwRegs.h>
#include <gtVct.h>
#include <gtSem.h>
#ifdef GT_USE_MAD
#include <gtMad.h>
#endif

#ifdef GT_USE_MAD
#include "gtPhyCtrl_mad.c"
#endif
/*
 * This routine set Auto-Negotiation Ad Register for Fast Ethernet Phy
*/
static
GT_STATUS feSetAutoMode
(
    IN GT_QD_DEV *dev,
    IN GT_U8      hwPort,
    IN GT_PHY_INFO     *phyInfo,
    IN GT_PHY_AUTO_MODE mode
)
{
    GT_U16             u16Data;

    GT_UNUSED_PARAM(phyInfo);

    DBG_INFO(("feSetAutoMode Called.\n"));

    if(hwReadPhyReg(dev,hwPort,QD_PHY_AUTONEGO_AD_REG,&u16Data) != GT_OK)
    {
        DBG_INFO(("Not able to read Phy Reg(port:%d,offset:%d).\n",hwPort,QD_PHY_AUTONEGO_AD_REG));
           return GT_FAIL;
    }

    /* Mask out all auto mode related bits. */
    u16Data &= ~QD_PHY_MODE_AUTO_AUTO;

    switch(mode)
    {
        case SPEED_AUTO_DUPLEX_AUTO:
                u16Data |= QD_PHY_MODE_AUTO_AUTO;
                break;
        case SPEED_100_DUPLEX_AUTO:
                u16Data |= QD_PHY_MODE_100_AUTO;
                break;
        case SPEED_10_DUPLEX_AUTO:
                u16Data |= QD_PHY_MODE_10_AUTO;
                break;
        case SPEED_AUTO_DUPLEX_FULL:
                u16Data |= QD_PHY_MODE_AUTO_FULL;
                break;
        case SPEED_AUTO_DUPLEX_HALF:
                u16Data |= QD_PHY_MODE_AUTO_HALF;
                break;
        case SPEED_100_DUPLEX_FULL:
                u16Data |= QD_PHY_100_FULL;
                break;
        case SPEED_100_DUPLEX_HALF:
                u16Data |= QD_PHY_100_HALF;
                break;
        case SPEED_10_DUPLEX_FULL:
                u16Data |= QD_PHY_10_FULL;
                break;
        case SPEED_10_DUPLEX_HALF:
                u16Data |= QD_PHY_10_HALF;
                break;
        default:
                 DBG_INFO(("Unknown Auto Mode (%d)\n",mode));
                return GT_BAD_PARAM;
    }

    /* Write to Phy AutoNegotiation Advertisement Register.  */
    if(hwWritePhyReg(dev,hwPort,QD_PHY_AUTONEGO_AD_REG,u16Data) != GT_OK)
    {
        DBG_INFO(("Not able to write Phy Reg(port:%d,offset:%d,data:%#x).\n",hwPort,QD_PHY_AUTONEGO_AD_REG,u16Data));
           return GT_FAIL;
    }

    return GT_OK;
}

/*
 * This routine get Auto-Negotiation Ad Register for Fast Ethernet Phy
*/
static
GT_STATUS feGetAutoMode
(
    IN  GT_QD_DEV        *dev,
    IN  GT_U8            hwPort,
    IN  GT_PHY_INFO      *phyInfo,
    OUT GT_PHY_AUTO_MODE *mode
)
{
    GT_U16  u16Data;

    GT_UNUSED_PARAM(phyInfo);

    DBG_INFO(("feGetAutoMode Called.\n"));

    if(hwReadPhyReg(dev,hwPort,QD_PHY_AUTONEGO_AD_REG,&u16Data) != GT_OK)
    {
        DBG_INFO(("Not able to read Phy Reg(port:%d,offset:%d).\n",hwPort,QD_PHY_AUTONEGO_AD_REG));
           return GT_FAIL;
    }

    /* Pick out all auto mode related bits. */
    u16Data &= QD_PHY_MODE_AUTO_AUTO;

    switch(u16Data)
    {
        case QD_PHY_MODE_10_HALF:
                *mode = SPEED_10_DUPLEX_HALF;
                break;
        case QD_PHY_MODE_10_FULL:
                *mode = SPEED_10_DUPLEX_FULL;
                break;
        case QD_PHY_MODE_100_HALF:
                *mode = SPEED_100_DUPLEX_HALF;
                break;
        case QD_PHY_MODE_100_FULL:
                *mode = SPEED_100_DUPLEX_FULL;
                break;
        case QD_PHY_MODE_AUTO_HALF:
                *mode = SPEED_AUTO_DUPLEX_HALF;
                break;
        case QD_PHY_MODE_AUTO_FULL:
                *mode = SPEED_AUTO_DUPLEX_FULL;
                break;
        case QD_PHY_MODE_10_AUTO:
                *mode = SPEED_10_DUPLEX_AUTO;
                break;
        case QD_PHY_MODE_100_AUTO:
                *mode = SPEED_100_DUPLEX_AUTO;
                break;
        case QD_PHY_MODE_AUTO_AUTO:
                *mode = SPEED_AUTO_DUPLEX_AUTO;
                break;
        default:
                DBG_INFO(("Unknown Auto Mode (%d)\n", u16Data));
                *mode = SPEED_AUTO_DUPLEX_AUTO;
                break;
    }

    return GT_OK;
}

/*
 * This routine set Auto-Negotiation Advertisement Register for Copper
*/
static
GT_STATUS gigCopperSetAutoMode
(
    IN GT_QD_DEV *dev,
    IN GT_U8 hwPort,
    IN GT_PHY_INFO     *phyInfo,
    IN GT_PHY_AUTO_MODE mode
)
{
    GT_U16             u16Data,u16Data1;

    DBG_INFO(("gigCopperSetAutoMode Called.\n"));

    if(hwReadPagedPhyReg(dev,hwPort,0,QD_PHY_AUTONEGO_AD_REG,phyInfo->anyPage,&u16Data) != GT_OK)
    {
        DBG_INFO(("Not able to read Phy Reg(port:%d,offset:%d).\n",hwPort,QD_PHY_AUTONEGO_AD_REG));
           return GT_FAIL;
    }

    /* Mask out all auto mode related bits. */
    u16Data &= ~QD_PHY_MODE_AUTO_AUTO;

    if(hwReadPagedPhyReg(dev,hwPort,0,QD_PHY_AUTONEGO_1000AD_REG,phyInfo->anyPage,&u16Data1) != GT_OK)
    {
        DBG_INFO(("Not able to read Phy Reg(port:%d,offset:%d).\n",hwPort,QD_PHY_AUTONEGO_AD_REG));
           return GT_FAIL;
    }

    /* Mask out all auto mode related bits. */
    u16Data1 &= ~(QD_GIGPHY_1000T_FULL|QD_GIGPHY_1000T_HALF);

    switch(mode)
    {
        case SPEED_AUTO_DUPLEX_AUTO:
                u16Data |= QD_PHY_MODE_AUTO_AUTO;
        case SPEED_1000_DUPLEX_AUTO:
                u16Data1 |= QD_GIGPHY_1000T_FULL|QD_GIGPHY_1000T_HALF;
                break;
        case SPEED_AUTO_DUPLEX_FULL:
                u16Data  |= QD_PHY_MODE_AUTO_FULL;
                u16Data1 |= QD_GIGPHY_1000T_FULL;
                break;
        case SPEED_1000_DUPLEX_FULL:
                u16Data1 |= QD_GIGPHY_1000T_FULL;
                break;
        case SPEED_1000_DUPLEX_HALF:
                u16Data1 |= QD_GIGPHY_1000T_HALF;
                break;
        case SPEED_AUTO_DUPLEX_HALF:
                u16Data  |= QD_PHY_MODE_AUTO_HALF;
                u16Data1 |= QD_GIGPHY_1000T_HALF;
                break;
        case SPEED_100_DUPLEX_AUTO:
                u16Data |= QD_PHY_MODE_100_AUTO;
                break;
        case SPEED_10_DUPLEX_AUTO:
                u16Data |= QD_PHY_MODE_10_AUTO;
                break;
        case SPEED_100_DUPLEX_FULL:
                u16Data |= QD_PHY_100_FULL;
                break;
        case SPEED_100_DUPLEX_HALF:
                u16Data |= QD_PHY_100_HALF;
                break;
        case SPEED_10_DUPLEX_FULL:
                u16Data |= QD_PHY_10_FULL;
                break;
        case SPEED_10_DUPLEX_HALF:
                u16Data |= QD_PHY_10_HALF;
                break;
        default:
                DBG_INFO(("Unknown Auto Mode (%d)\n",mode));
                return GT_BAD_PARAM;
    }

    /* Write to Phy AutoNegotiation Advertisement Register.  */
    if(hwWritePagedPhyReg(dev,hwPort,0,QD_PHY_AUTONEGO_AD_REG,phyInfo->anyPage,u16Data) != GT_OK)
    {
        DBG_INFO(("Not able to write Phy Reg(port:%d,offset:%d,data:%#x).\n",hwPort,QD_PHY_AUTONEGO_AD_REG,u16Data));
           return GT_FAIL;
    }

    /* Write to Phy AutoNegotiation 1000B Advertisement Register.  */
    if(hwWritePagedPhyReg(dev,hwPort,0,QD_PHY_AUTONEGO_1000AD_REG,phyInfo->anyPage,u16Data1) != GT_OK)
    {
        DBG_INFO(("Not able to read Phy Reg(port:%d,offset:%d).\n",hwPort,QD_PHY_AUTONEGO_AD_REG));
           return GT_FAIL;
    }

    return GT_OK;
}

/*
 * This routine get Auto-Negotiation Ad Register for Copper
*/
static
GT_STATUS gigCopperGetAutoMode
(
    IN GT_QD_DEV        *dev,
    IN GT_U8            hwPort,
    IN GT_PHY_INFO      *phyInfo,
    IN GT_PHY_AUTO_MODE *mode
)
{
    GT_U16 u16Data, u16Data1;
    GT_U32 u32Data;

    DBG_INFO(("gigCopperGetAutoMode Called.\n"));

    if(hwReadPagedPhyReg(dev,hwPort,0,QD_PHY_AUTONEGO_AD_REG,phyInfo->anyPage,&u16Data) != GT_OK)
    {
        DBG_INFO(("Not able to read Phy Reg(port:%d,offset:%d).\n",hwPort,QD_PHY_AUTONEGO_AD_REG));
           return GT_FAIL;
    }

    /* Pick out all auto mode related bits. */
    u16Data &= QD_PHY_MODE_AUTO_AUTO;

    if(hwReadPagedPhyReg(dev,hwPort,0,QD_PHY_AUTONEGO_1000AD_REG,phyInfo->anyPage,&u16Data1) != GT_OK)
    {
        DBG_INFO(("Not able to read Phy Reg(port:%d,offset:%d).\n",hwPort,QD_PHY_AUTONEGO_AD_REG));
           return GT_FAIL;
    }

    /* Pick out all auto mode related bits. */
    u16Data1 &= (QD_GIGPHY_1000T_FULL|QD_GIGPHY_1000T_HALF);

    u32Data  = (u16Data&0xffff)|((u16Data1&0xffff)<<16);

    switch(u32Data)
    {
        case QD_PHY_MODE_10_HALF:
                *mode = SPEED_10_DUPLEX_HALF;
                break;
        case QD_PHY_MODE_10_FULL:
                *mode = SPEED_10_DUPLEX_FULL;
                break;
        case QD_PHY_MODE_100_HALF:
                *mode = SPEED_100_DUPLEX_HALF;
                break;
        case QD_PHY_MODE_100_FULL:
                *mode = SPEED_100_DUPLEX_FULL;
                break;
        case (QD_GIGPHY_1000T_HALF<<16):
                *mode = SPEED_1000_DUPLEX_HALF;
                break;
        case (QD_GIGPHY_1000T_FULL<<16):
                *mode = SPEED_1000_DUPLEX_FULL;
                break;
        case QD_PHY_MODE_AUTO_HALF|(QD_GIGPHY_1000T_HALF<<16):
                *mode = SPEED_AUTO_DUPLEX_HALF;
                break;
        case QD_PHY_MODE_AUTO_FULL|(QD_GIGPHY_1000T_FULL<<16):
                *mode = SPEED_AUTO_DUPLEX_FULL;
                break;
        case QD_PHY_MODE_10_AUTO:
                *mode = SPEED_10_DUPLEX_AUTO;
                break;
        case QD_PHY_MODE_100_AUTO:
                *mode = SPEED_100_DUPLEX_AUTO;
                break;
        case ((QD_GIGPHY_1000T_FULL|QD_GIGPHY_1000T_HALF)<<16):
                *mode = SPEED_1000_DUPLEX_AUTO;
                break;
        case QD_PHY_MODE_AUTO_AUTO|((QD_GIGPHY_1000T_FULL|QD_GIGPHY_1000T_HALF)<<16):
                *mode = SPEED_AUTO_DUPLEX_AUTO;
                break;
        default:
                *mode = SPEED_AUTO_DUPLEX_AUTO;
                DBG_INFO(("Unknown Auto Mode (%08x)\n", u32Data));
                break;
    }

    return GT_OK;
}

/*
 * This routine set Auto-Negotiation Ad Register for Fiber
*/
static
GT_STATUS gigFiberSetAutoMode
(
    IN GT_QD_DEV *dev,
    IN GT_U8 hwPort,
    IN GT_PHY_INFO     *phyInfo,
    IN GT_PHY_AUTO_MODE mode
)
{
    GT_U16             u16Data;

    DBG_INFO(("gigPhySetAutoMode Called.\n"));

    if(hwReadPagedPhyReg(dev,hwPort,1,QD_PHY_AUTONEGO_AD_REG,phyInfo->anyPage,&u16Data) != GT_OK)
    {
        DBG_INFO(("Not able to read Phy Reg(port:%d,offset:%d).\n",hwPort,QD_PHY_AUTONEGO_AD_REG));
           return GT_FAIL;
    }

    /* Mask out all auto mode related bits. */
    u16Data &= ~(QD_GIGPHY_1000X_FULL|QD_GIGPHY_1000X_HALF);

    switch(mode)
    {
        case SPEED_AUTO_DUPLEX_AUTO:
        case SPEED_1000_DUPLEX_AUTO:
                u16Data |= QD_GIGPHY_1000X_FULL|QD_GIGPHY_1000X_HALF;
                break;
        case SPEED_AUTO_DUPLEX_FULL:
        case SPEED_1000_DUPLEX_FULL:
                u16Data |= QD_GIGPHY_1000X_FULL;
                break;
        case SPEED_AUTO_DUPLEX_HALF:
        case SPEED_1000_DUPLEX_HALF:
                u16Data |= QD_GIGPHY_1000X_HALF;
                break;
        default:
                    DBG_INFO(("Unknown Auto Mode (%d)\n",mode));
                return GT_BAD_PARAM;
    }

    /* Write to Phy AutoNegotiation Advertisement Register.  */
    if(hwWritePagedPhyReg(dev,hwPort,1,QD_PHY_AUTONEGO_AD_REG,phyInfo->anyPage,u16Data) != GT_OK)
    {
        DBG_INFO(("Not able to write Phy Reg(port:%d,offset:%d,data:%#x).\n",hwPort,QD_PHY_AUTONEGO_AD_REG,u16Data));
           return GT_FAIL;
    }

    return GT_OK;
}

/*
 * This routine sets Auto Mode and Reset the phy
*/
static
GT_STATUS phySetAutoMode
(
    IN GT_QD_DEV *dev,
    IN GT_U8 hwPort,
    IN GT_PHY_INFO *phyInfo,
    IN GT_PHY_AUTO_MODE mode
)
{
    GT_U16         u16Data;
    GT_STATUS    status;
    GT_BOOL            autoOn;
    GT_U16            pageReg;

    DBG_INFO(("phySetAutoMode Called.\n"));

    if (!(phyInfo->flag & GT_PHY_GIGABIT))
    {
        if((status=feSetAutoMode(dev,hwPort,phyInfo,mode)) != GT_OK)
        {
               return status;
        }

        u16Data = QD_PHY_SPEED | QD_PHY_DUPLEX | QD_PHY_AUTONEGO;

        DBG_INFO(("Write to phy(%d) register: regAddr 0x%x, data %#x",
                  hwPort,QD_PHY_CONTROL_REG,u16Data));

        /* soft reset */
        return hwPhyReset(dev,hwPort,u16Data);
    }

    if(driverPagedAccessStart(dev,hwPort,phyInfo->pageType,&autoOn,&pageReg) != GT_OK)
    {
        return GT_FAIL;
    }

    if(phyInfo->flag & GT_PHY_COPPER)
    {
        if((status=gigCopperSetAutoMode(dev,hwPort,phyInfo,mode)) != GT_OK)
        {
               return status;
        }

        u16Data = QD_PHY_AUTONEGO;

        DBG_INFO(("Write to phy(%d) register: regAddr 0x%x, data %#x",
                  hwPort,QD_PHY_CONTROL_REG,u16Data));

        /* Write to Phy Control Register.  */
        if(hwWritePagedPhyReg(dev,hwPort,0,QD_PHY_CONTROL_REG,phyInfo->anyPage,u16Data) != GT_OK)
            return GT_FAIL;
    }
    else if(phyInfo->flag & GT_PHY_FIBER)
    {
        if((status=gigFiberSetAutoMode(dev,hwPort,phyInfo,mode)) != GT_OK)
        {
               return status;
        }
        u16Data = QD_PHY_AUTONEGO;

        DBG_INFO(("Write to phy(%d) register: regAddr 0x%x, data %#x",
                  hwPort,QD_PHY_CONTROL_REG,u16Data));

        /* Write to Phy Control Register.  */
        if(hwWritePagedPhyReg(dev,hwPort,1,QD_PHY_CONTROL_REG,phyInfo->anyPage,u16Data) != GT_OK)
            return GT_FAIL;
    }

    if(driverPagedAccessStop(dev,hwPort,phyInfo->pageType,autoOn,pageReg) != GT_OK)
    {
        return GT_FAIL;
    }

    return hwPhyReset(dev,hwPort,0xFF);
}

/*
 * This routine gets Auto Mode
*/
static
GT_STATUS phyGetAutoMode
(
    IN  GT_QD_DEV        *dev,
    IN  GT_U8            hwPort,
    IN  GT_PHY_INFO      *phyInfo,
    OUT GT_PHY_AUTO_MODE *mode
)
{
    GT_STATUS    status;
    GT_BOOL      autoOn;
    GT_U16       pageReg;

    DBG_INFO(("phyGetAutoMode Called.\n"));

    if (!(phyInfo->flag & GT_PHY_GIGABIT))
    {
        if((status=feGetAutoMode(dev,hwPort,phyInfo,mode)) != GT_OK)
        {
               return status;
        }
        return status;
    }

    if(driverPagedAccessStart(dev,hwPort,phyInfo->pageType,&autoOn,&pageReg) != GT_OK)
    {
        return GT_FAIL;
    }

    if(phyInfo->flag & GT_PHY_COPPER)
    {
        if((status=gigCopperGetAutoMode(dev,hwPort,phyInfo,mode)) != GT_OK)
        {
               return status;
        }
    }
    else if(phyInfo->flag & GT_PHY_FIBER)
    {
        return GT_NOT_SUPPORTED;
    }

    if(driverPagedAccessStop(dev,hwPort,phyInfo->pageType,autoOn,pageReg) != GT_OK)
    {
        return GT_FAIL;
    }

    return status;
}

/*******************************************************************************
* gprtPhyReset
*
* DESCRIPTION:
*       This routine preforms PHY reset.
*        After reset, phy will be in Autonegotiation mode.
*
* INPUTS:
* port - The logical port number, unless SERDES device is accessed
*        The physical address, if SERDES device is accessed
*
* OUTPUTS:
*       None.
*
* RETURNS:
*       GT_OK   - on success
*       GT_FAIL - on error
* COMMENTS:
* data sheet register 0.15 - Reset
* data sheet register 0.13 - Speed
* data sheet register 0.12 - Autonegotiation
* data sheet register 0.8  - Duplex Mode
*******************************************************************************/

GT_STATUS gprtPhyReset
(
    IN GT_QD_DEV *dev,
    IN GT_LPORT  port
)
{

    GT_STATUS       retVal;         /* Functions return value.      */
    GT_U8           hwPort;         /* the physical port number     */
    GT_PHY_INFO        phyInfo;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtPhyReset_mad(dev, port);
#endif

    DBG_INFO(("gprtPhyReset Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    /* set Auto Negotiation AD Register */
    retVal = phySetAutoMode(dev,hwPort,&phyInfo,SPEED_AUTO_DUPLEX_AUTO);

    if(retVal != GT_OK)
    {
        DBG_INFO(("Failed.\n"));
    }
    else
    {
        DBG_INFO(("OK.\n"));
    }

    gtSemGive(dev,dev->phyRegsSem);

    return retVal;
}


/*******************************************************************************
* gprtSetPortLoopback
*
* DESCRIPTION:
* Enable/Disable Internal Port Loopback.
* For 10/100 Fast Ethernet PHY, speed of Loopback is determined as follows:
*   If Auto-Negotiation is enabled, this routine disables Auto-Negotiation and
*   forces speed to be 10Mbps.
*   If Auto-Negotiation is disabled, the forced speed is used.
*   Disabling Loopback simply clears bit 14 of control register(0.14). Therefore,
*   it is recommended to call gprtSetPortAutoMode for PHY configuration after
*   Loopback test.
* For 10/100/1000 Gigagbit Ethernet PHY, speed of Loopback is determined as follows:
*   If Auto-Negotiation is enabled and Link is active, the current speed is used.
*   If Auto-Negotiation is disabled, the forced speed is used.
*   All other cases, default MAC Interface speed is used. Please refer to the data
*   sheet for the information of the default MAC Interface speed.
*
*
* INPUTS:
* port - The logical port number, unless SERDES device is accessed
*        The physical address, if SERDES device is accessed
* enable - If GT_TRUE, enable loopback mode
* If GT_FALSE, disable loopback mode
*
* OUTPUTS:
* None.
*
* RETURNS:
* GT_OK - on success
* GT_FAIL - on error
*
* COMMENTS:
* data sheet register 0.14 - Loop_back
*
*******************************************************************************/

GT_STATUS gprtSetPortLoopback
(
    IN GT_QD_DEV *dev,
    IN GT_LPORT  port,
    IN GT_BOOL   enable
)
{
    GT_STATUS       retVal;         /* Functions return value.      */
    GT_U8           hwPort;         /* the physical port number     */
    GT_U16             u16Data;
    GT_PHY_INFO        phyInfo;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtSetPortLoopback_mad(dev, port, enable);
#endif

    DBG_INFO(("gprtSetPortLoopback Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if(hwReadPhyReg(dev,hwPort,QD_PHY_CONTROL_REG,&u16Data) != GT_OK)
    {
        DBG_INFO(("Not able to read Phy Reg(port:%d,offset:%d).\n",hwPort,QD_PHY_CONTROL_REG));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    /* is this Fast Ethernet Phy? */
    if (!(phyInfo.flag & GT_PHY_GIGABIT))
    {
        if(enable)
        {
            if(u16Data & QD_PHY_AUTONEGO)
            {
                /* disable Auto-Neg and force speed to be 10Mbps */
                u16Data = u16Data & QD_PHY_DUPLEX;

                if((retVal=hwPhyReset(dev,hwPort,u16Data)) != GT_OK)
                {
                    DBG_INFO(("Softreset failed.\n"));
                    gtSemGive(dev,dev->phyRegsSem);
                    return retVal;
                }
            }
        }
    }

    BOOL_2_BIT(enable,u16Data);

    /* Write to Phy Control Register.  */
    retVal = hwSetPhyRegField(dev,hwPort,QD_PHY_CONTROL_REG,14,1,u16Data);
    if(retVal != GT_OK)
    {
        DBG_INFO(("Failed.\n"));
    }
    else
    {
        DBG_INFO(("OK.\n"));
    }
    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}

/*******************************************************************************
* gprtGetPortLoopback
*
* DESCRIPTION:
* Get Internal Port Loopback state.
* For 10/100 Fast Ethernet PHY, speed of Loopback is determined as follows:
*   If Auto-Negotiation is enabled, this routine disables Auto-Negotiation and
*   forces speed to be 10Mbps.
*   If Auto-Negotiation is disabled, the forced speed is used.
*   Disabling Loopback simply clears bit 14 of control register(0.14). Therefore,
*   it is recommended to call gprtSetPortAutoMode for PHY configuration after
*   Loopback test.
* For 10/100/1000 Gigagbit Ethernet PHY, speed of Loopback is determined as follows:
*   If Auto-Negotiation is enabled and Link is active, the current speed is used.
*   If Auto-Negotiation is disabled, the forced speed is used.
*   All other cases, default MAC Interface speed is used. Please refer to the data
*   sheet for the information of the default MAC Interface speed.
*
*
* INPUTS:
*       port - The logical port number, unless SERDES device is accessed
*              The physical address, if SERDES device is accessed
*
* OUTPUTS:
*       enable - If GT_TRUE,  loopback mode is enabled
*       If GT_FALSE,  loopback mode is disabled
*
* RETURNS:
*       GT_OK - on success
*       GT_FAIL - on error
*
* COMMENTS:
*       data sheet register 0.14 - Loop_back
*
*******************************************************************************/
GT_STATUS gprtGetPortLoopback
(
    IN GT_QD_DEV *dev,
    IN GT_LPORT  port,
    OUT GT_BOOL  *enable
)
{
    GT_STATUS      retVal;         /* Functions return value.      */
    GT_U8          hwPort;         /* the physical port number     */
    GT_U16         u16Data;
    GT_PHY_INFO    phyInfo;

    DBG_INFO(("gprtGetPortLoopback Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    /*get loopback state*/
    retVal = hwGetPhyRegField(dev,hwPort,QD_PHY_CONTROL_REG,14,1,&u16Data);
    if(retVal != GT_OK)
    {
        DBG_INFO(("Failed.\n"));
    }
    else
    {
        DBG_INFO(("OK.\n"));
        BIT_2_BOOL(u16Data, *enable);
    }

    return retVal;
}

/*******************************************************************************
* gprtSetPortLineLoopback
*
* DESCRIPTION:
*        Enable/Disable Port Line Loopback.
*
* INPUTS:
*        port   - The logical port number, unless SERDES device is accessed
*                 The physical address, if SERDES device is accessed
*        enable - If GT_TRUE, enable loopback mode
*                 If GT_FALSE, disable loopback mode
*
* OUTPUTS:
*        None.
*
* RETURNS:
*        GT_OK - on success
*        GT_FAIL - on error
*
* COMMENTS:
*        data sheet register FE:28.4, GE:21_2.14  - Loop_back
*
*******************************************************************************/
GT_STATUS gprtSetPortLineLoopback
(
    IN GT_QD_DEV *dev,
    IN GT_LPORT  port,
    IN GT_BOOL   enable
)
{
    GT_STATUS      retVal;         /* Functions return value.      */
    GT_U8          hwPort;         /* the physical port number     */
    GT_U16         u16Data;
    GT_PHY_INFO    phyInfo;
    GT_U16         pageReg;

    DBG_INFO(("gprtSetPortLineLoopback Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    BOOL_2_BIT(enable,u16Data);

    /* GE Phy */
    if ((phyInfo.flag & GT_PHY_GIGABIT))
    {
        if(driverPagedAccessStart(dev,hwPort,phyInfo.pageType,0,&pageReg) != GT_OK)
        {
            return GT_FAIL;
        }
        /* Write to GE PHY MAC specific control register.  */
        retVal = hwSetPagedPhyRegField(dev,hwPort, 2, QD_PHY_GE_LINE_LOOPBACK_REG,14,1,phyInfo.anyPage, u16Data);

        if(driverPagedAccessStop(dev,hwPort,phyInfo.pageType,0,pageReg) != GT_OK)
        {
            return GT_FAIL;
        }
    }
    else /* FE Phy */
    {
        /* Write to FE PHY specific control register.  */
        retVal = hwSetPhyRegField(dev,hwPort,QD_PHY_FE_LINE_LOOPBACK_REG,4,1,u16Data);
    }

    if(retVal != GT_OK)
    {
        DBG_INFO(("Failed.\n"));
    }
    else
    {
        DBG_INFO(("OK.\n"));
    }
    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}

/*******************************************************************************
* gprtGetPortLineLoopback
*
* DESCRIPTION:
*       Get Port Line Loopback status.
*
*
* INPUTS:
*       port - The logical port number, unless SERDES device is accessed
*              The physical address, if SERDES device is accessed
*
* OUTPUTS:
*       enable - If GT_TRUE, enable loopback mode
*                If GT_FALSE, disable loopback mode* enable - If GT_TRUE, enable loopback mode
*                If GT_FALSE, disable loopback mode
*
* RETURNS:
*      GT_OK - on success
*      GT_FAIL - on error
*
* COMMENTS:
*      data sheet register FE:28.4, GE:21_2.14  - Loop_back
*
*******************************************************************************/
GT_STATUS gprtGetPortLineLoopback
(
    IN GT_QD_DEV *dev,
    IN GT_LPORT  port,
    OUT GT_BOOL  *enable
)
{
    GT_STATUS      retVal;         /* Functions return value.      */
    GT_U8          hwPort;         /* the physical port number     */
    GT_U16         u16Data;
    GT_PHY_INFO    phyInfo;
    GT_U16         pageReg;

    DBG_INFO(("gprtGetPortLineLoopback Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

     /* GE Phy */
    if ((phyInfo.flag & GT_PHY_GIGABIT))
    {
        if(driverPagedAccessStart(dev,hwPort,phyInfo.pageType,0,&pageReg) != GT_OK)
        {
            return GT_FAIL;
        }
        /* Read to GE PHY MAC specific control register.  */
        retVal = hwGetPagedPhyRegField(dev,hwPort, 2, QD_PHY_GE_LINE_LOOPBACK_REG,14,1,phyInfo.anyPage,&u16Data);

        if(driverPagedAccessStop(dev,hwPort,phyInfo.pageType,0,pageReg) != GT_OK)
        {
            return GT_FAIL;
        }
    }
    else /* FE Phy */
    {
        /* Read to FE PHY specific control register.  */
        retVal = hwGetPhyRegField(dev,hwPort,QD_PHY_FE_LINE_LOOPBACK_REG,4,1,&u16Data);
    }

    if(retVal != GT_OK)
    {
        DBG_INFO(("Failed.\n"));
    }
    else
    {
        DBG_INFO(("OK.\n"));
    }

    BIT_2_BOOL(u16Data, *enable);

    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}

/*******************************************************************************
* gprtSetPortSpeed
*
* DESCRIPTION:
*         Sets speed for a specific logical port. This function will keep the duplex
*        mode and loopback mode to the previous value, but disable others, such as
*        Autonegotiation.
*
* INPUTS:
*        port -    The logical port number, unless SERDES device is accessed
*                The physical address, if SERDES device is accessed
*        speed - port speed.
*                PHY_SPEED_10_MBPS for 10Mbps
*                PHY_SPEED_100_MBPS for 100Mbps
*                PHY_SPEED_1000_MBPS for 1000Mbps
*
* OUTPUTS:
* None.
*
* RETURNS:
* GT_OK - on success
* GT_FAIL - on error
*
* COMMENTS:
* data sheet register 0.13 - Speed Selection (LSB)
* data sheet register 0.6  - Speed Selection (MSB)
*
*******************************************************************************/

GT_STATUS gprtSetPortSpeed
(
IN GT_QD_DEV *dev,
IN GT_LPORT  port,
IN GT_PHY_SPEED speed
)
{
    GT_U8           hwPort;         /* the physical port number     */
    GT_U16             u16Data;
    GT_PHY_INFO        phyInfo;
    GT_STATUS        retVal;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtSetPortSpeed_mad(dev, port, speed);
#endif

    DBG_INFO(("gprtSetPortSpeed Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if(hwReadPhyReg(dev,hwPort,QD_PHY_CONTROL_REG,&u16Data) != GT_OK)
    {
        DBG_INFO(("Not able to read Phy Reg(port:%d,offset:%d).\n",hwPort,QD_PHY_CONTROL_REG));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    switch(speed)
    {
        case PHY_SPEED_10_MBPS:
            if ((phyInfo.flag & GT_PHY_GIGABIT) && !(phyInfo.flag & GT_PHY_COPPER))
            {
                gtSemGive(dev,dev->phyRegsSem);
                return GT_BAD_PARAM;
            }
            u16Data = u16Data & (QD_PHY_LOOPBACK | QD_PHY_DUPLEX);
            break;
        case PHY_SPEED_100_MBPS:
            u16Data = (u16Data & (QD_PHY_LOOPBACK | QD_PHY_DUPLEX)) | QD_PHY_SPEED;
            break;
        case PHY_SPEED_1000_MBPS:
            if (!(phyInfo.flag & GT_PHY_GIGABIT))
            {
                gtSemGive(dev,dev->phyRegsSem);
                return GT_BAD_PARAM;
            }
            u16Data = (u16Data & (QD_PHY_LOOPBACK | QD_PHY_DUPLEX)) | QD_PHY_SPEED_MSB;
            break;
        default:
            gtSemGive(dev,dev->phyRegsSem);
            return GT_FAIL;
    }

    DBG_INFO(("Write to phy(%d) register: regAddr 0x%x, data %#x",
              hwPort,QD_PHY_CONTROL_REG,u16Data));

    retVal = hwPhyReset(dev,hwPort,u16Data);
      gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}


/*******************************************************************************
* gprtPortAutoNegEnable
*
* DESCRIPTION:
*         Enable/disable an Auto-Negotiation.
*        This routine simply sets Auto Negotiation bit (bit 12) of Control
*        Register and reset the phy.
*        For Speed and Duplex selection, please use gprtSetPortAutoMode.
*
* INPUTS:
*        port -  The logical port number, unless SERDES device is accessed
*                The physical address, if SERDES device is accessed
*         state - GT_TRUE for enable Auto-Negotiation,
*                GT_FALSE otherwise
*
* OUTPUTS:
*         None.
*
* RETURNS:
*         GT_OK     - on success
*         GT_FAIL     - on error
*
* COMMENTS:
*         data sheet register 0.12 - Auto-Negotiation Enable
*         data sheet register 4.8, 4.7, 4.6, 4.5 - Auto-Negotiation Advertisement
*
*******************************************************************************/
GT_STATUS gprtPortAutoNegEnable
(
    IN GT_QD_DEV *dev,
    IN GT_LPORT  port,
    IN GT_BOOL   state
)
{
    GT_U8           hwPort;         /* the physical port number     */
    GT_U16             u16Data;
    GT_STATUS        retVal;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtPortAutoNegEnable_mad(dev, port, state);
#endif

    DBG_INFO(("gprtPortAutoNegEnable Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if(!IS_CONFIGURABLE_PHY(dev,hwPort))
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(hwReadPhyReg(dev,hwPort,QD_PHY_CONTROL_REG,&u16Data) != GT_OK)
    {
        DBG_INFO(("Not able to read Phy Reg(port:%d,offset:%d).\n",hwPort,QD_PHY_CONTROL_REG));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if(state)
    {
        u16Data = (u16Data & (QD_PHY_SPEED | QD_PHY_DUPLEX)) | QD_PHY_AUTONEGO;
    }
    else
    {
        u16Data = u16Data & (QD_PHY_SPEED | QD_PHY_DUPLEX);
    }


    DBG_INFO(("Write to phy(%d) register: regAddr 0x%x, data %#x",
              hwPort,QD_PHY_CONTROL_REG,u16Data));

    retVal = hwPhyReset(dev,hwPort,u16Data);
    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}

/*******************************************************************************
* gprtGetPortAutoNegState
*
* DESCRIPTION:
*         Read the auto negotiation state of specific logical port.
*         This routine simply reads Auto Negotiation bit (bit 12) of Control
*         Register.
*
* INPUTS:
*         port    - The logical port number, unless SERDES device is accessed
*                   The physical address, if SERDES device is accessed
*
* OUTPUTS:
*         state   - GT_TRUE for enable Auto-Negotiation,
*                   GT_FALSE otherwise
*
* RETURNS:
*         GT_OK   - on success
*         GT_FAIL - on error
*
* COMMENTS:
*         data sheet register 0.12 - Auto-Negotiation Enable
*         data sheet register 4.8, 4.7, 4.6, 4.5 - Auto-Negotiation Advertisement
*******************************************************************************/
GT_STATUS gprtGetPortAutoNegState
(
    IN  GT_QD_DEV *dev,
    IN  GT_LPORT  port,
    OUT GT_BOOL   *state
)
{
    GT_U8        hwPort;  /* the physical port number     */
    GT_U16       u16Data;
    GT_STATUS    retVal;

    DBG_INFO(("gprtGetPortAutoNegState Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if(!IS_CONFIGURABLE_PHY(dev,hwPort))
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    /* read the auto negotiation state from bit 12 of PHY control register */
    if((retVal=hwGetPhyRegField(dev,hwPort,QD_PHY_CONTROL_REG,12,1,&u16Data)) != GT_OK)
    {
        DBG_INFO(("Failed.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return retVal;
    }

    BIT_2_BOOL(u16Data, *state);

    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}

/*******************************************************************************
* gprtPortPowerDown
*
* DESCRIPTION:
*         Enable/disable (power down) on specific logical port.
*        Phy configuration remains unchanged after Power down.
*
* INPUTS:
*        port -    The logical port number, unless SERDES device is accessed
*                The physical address, if SERDES device is accessed
*         state -    GT_TRUE: power down
*                 GT_FALSE: normal operation
*
* OUTPUTS:
*         None.
*
* RETURNS:
*         GT_OK     - on success
*         GT_FAIL     - on error
*
* COMMENTS:
*         data sheet register 0.11 - Power Down
*
*******************************************************************************/

GT_STATUS gprtPortPowerDown
(
IN GT_QD_DEV *dev,
IN GT_LPORT  port,
IN GT_BOOL   state
)
{
    GT_STATUS       retVal;         /* Functions return value.      */
    GT_U8           hwPort;         /* the physical port number     */
    GT_U16             u16Data;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtPortPowerDown_mad(dev, port, state);
#endif

    DBG_INFO(("gprtPortPowerDown Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if(!IS_CONFIGURABLE_PHY(dev,hwPort))
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    BOOL_2_BIT(state,u16Data);

    if((retVal=hwSetPhyRegField(dev,hwPort,QD_PHY_CONTROL_REG,11,1,u16Data)) != GT_OK)
    {
        DBG_INFO(("Failed.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return retVal;
    }

    gtSemGive(dev,dev->phyRegsSem);
    return GT_OK;
}

/*******************************************************************************
* gprtGetPortPowerDown
*
* DESCRIPTION:
*         Read Port state (power down/normal operation) on specific logical port.
*
* INPUTS:
*         port    - The logical port number, unless SERDES device is accessed
*                   The physical address, if SERDES device is accessed
*
* OUTPUTS:
*         state   - GT_TRUE: power down
*                   GT_FALSE: normal operation
*
* RETURNS:
*         GT_OK   - on success
*         GT_FAIL - on error
*
* COMMENTS:
*         data sheet register 0.11 - Power Down
*
*******************************************************************************/
GT_STATUS gprtGetPortPowerDown
(
    IN  GT_QD_DEV *dev,
    IN  GT_LPORT  port,
    OUT GT_BOOL   *state
)
{
    GT_STATUS    retVal;         /* Functions return value.      */
    GT_U8        hwPort;         /* the physical port number     */
    GT_U16       u16Data;

#ifdef GT_USE_MAD

#endif

    DBG_INFO(("gprtGetPortPowerDown Called.\n"));

    if(state == NULL)
    {
        DBG_INFO(("input pointer is NULL, return\n"));
    }

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if(!IS_CONFIGURABLE_PHY(dev,hwPort))
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if((retVal=hwGetPhyRegField(dev,hwPort,QD_PHY_CONTROL_REG,11,1,&u16Data)) != GT_OK)
    {
        DBG_INFO(("Failed.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return retVal;
    }

    BIT_2_BOOL(u16Data, *state);

    gtSemGive(dev,dev->phyRegsSem);
    return GT_OK;
}

/*******************************************************************************
* gprtPortRestartAutoNeg
*
* DESCRIPTION:
*         Restart AutoNegotiation. If AutoNegotiation is not enabled, it'll enable
*        it. Loopback and Power Down will be disabled by this routine.
*
* INPUTS:
*        port -    The logical port number, unless SERDES device is accessed
*                The physical address, if SERDES device is accessed
*
* OUTPUTS:
*         None.
*
* RETURNS:
*         GT_OK     - on success
*         GT_FAIL     - on error
*
* COMMENTS:
*         data sheet register 0.9 - Restart Auto-Negotiation
*
*******************************************************************************/

GT_STATUS gprtPortRestartAutoNeg
(
IN GT_QD_DEV *dev,
IN GT_LPORT  port
)
{
    GT_STATUS       retVal;
    GT_U8           hwPort;         /* the physical port number     */
    GT_U16             u16Data;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtPortRestartAutoNeg_mad(dev, port);
#endif

    DBG_INFO(("gprtPortRestartAutoNeg Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if(!IS_CONFIGURABLE_PHY(dev,hwPort))
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(hwReadPhyReg(dev,hwPort,QD_PHY_CONTROL_REG,&u16Data) != GT_OK)
    {
        DBG_INFO(("Not able to read Phy Reg(port:%d,offset:%d).\n",hwPort,QD_PHY_CONTROL_REG));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    u16Data &= (QD_PHY_DUPLEX | QD_PHY_SPEED);
    u16Data |= (QD_PHY_RESTART_AUTONEGO | QD_PHY_AUTONEGO);

    DBG_INFO(("Write to phy(%d) register: regAddr 0x%x, data %#x",
              hwPort,QD_PHY_CONTROL_REG,u16Data));

    /* Write to Phy Control Register.  */
    retVal = hwWritePhyReg(dev,hwPort,QD_PHY_CONTROL_REG,u16Data);
    gtSemGive(dev,dev->phyRegsSem);

    if(retVal != GT_OK)
    {
        DBG_INFO(("Failed.\n"));
    }
    else
    {
        DBG_INFO(("OK.\n"));
    }
    return retVal;
}

/*******************************************************************************
* gprtSetPortDuplexMode
*
* DESCRIPTION:
*         Sets duplex mode for a specific logical port. This function will keep
*        the speed and loopback mode to the previous value, but disable others,
*        such as Autonegotiation.
*
* INPUTS:
*        port -    The logical port number, unless SERDES device is accessed
*                The physical address, if SERDES device is accessed
*         dMode    - dulpex mode
*
* OUTPUTS:
*         None.
*
* RETURNS:
*         GT_OK     - on success
*         GT_FAIL     - on error
*
* COMMENTS:
*         data sheet register 0.8 - Duplex Mode
*
*******************************************************************************/
GT_STATUS gprtSetPortDuplexMode
(
IN GT_QD_DEV *dev,
IN GT_LPORT  port,
IN GT_BOOL   dMode
)
{
    GT_U8           hwPort;         /* the physical port number     */
    GT_U16             u16Data;
    GT_STATUS        retVal;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtSetPortDuplexMode_mad(dev, port, dMode);
#endif

    DBG_INFO(("gprtSetPortDuplexMode Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if(!IS_CONFIGURABLE_PHY(dev,hwPort))
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(hwReadPhyReg(dev,hwPort,QD_PHY_CONTROL_REG,&u16Data) != GT_OK)
    {
        DBG_INFO(("Not able to read Phy Reg(port:%d,offset:%d).\n",hwPort,QD_PHY_CONTROL_REG));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if(dMode)
    {
        u16Data = (u16Data & (QD_PHY_LOOPBACK | QD_PHY_SPEED | QD_PHY_SPEED_MSB)) | QD_PHY_DUPLEX;
    }
    else
    {
        u16Data = u16Data & (QD_PHY_LOOPBACK | QD_PHY_SPEED | QD_PHY_SPEED_MSB);
    }


    DBG_INFO(("Write to phy(%d) register: regAddr 0x%x, data %#x",
              hwPort,QD_PHY_CONTROL_REG,u16Data));

    /* Write to Phy Control Register.  */
    retVal = hwPhyReset(dev,hwPort,u16Data);
    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}


/*******************************************************************************
* gprtSetPortAutoMode
*
* DESCRIPTION:
*         This routine sets up the port with given Auto Mode.
*        Supported mode is as follows:
*        - Auto for both speed and duplex.
*        - Auto for speed only and Full duplex.
*        - Auto for speed only and Half duplex.
*        - Auto for duplex only and speed 1000Mbps.
*        - Auto for duplex only and speed 100Mbps.
*        - Auto for duplex only and speed 10Mbps.
*        - Speed 1000Mbps and Full duplex.
*        - Speed 1000Mbps and Half duplex.
*        - Speed 100Mbps and Full duplex.
*        - Speed 100Mbps and Half duplex.
*        - Speed 10Mbps and Full duplex.
*        - Speed 10Mbps and Half duplex.
*
*
* INPUTS:
*        port -    The logical port number, unless SERDES device is accessed
*                The physical address, if SERDES device is accessed
*         mode - Auto Mode to be written
*
* OUTPUTS:
*        None.
*
* RETURNS:
*        GT_OK   - on success
*        GT_FAIL - on error
*        GT_NOT_SUPPORTED - on device without copper
*
* COMMENTS:
*         data sheet register 4.8, 4.7, 4.6, and 4.5 Autonegotiation Advertisement
*         data sheet register 4.6, 4.5 Autonegotiation Advertisement for 1000BX
*         data sheet register 9.9, 9.8 Autonegotiation Advertisement for 1000BT
*******************************************************************************/

GT_STATUS gprtSetPortAutoMode
(
    IN GT_QD_DEV *dev,
    IN GT_LPORT  port,
    IN GT_PHY_AUTO_MODE mode
)
{

    GT_STATUS       retVal;         /* Functions return value.      */
    GT_U8           hwPort;         /* the physical port number     */
    GT_PHY_INFO        phyInfo;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtSetPortAutoMode_mad(dev, port, mode);
#endif

    DBG_INFO(("gprtSetPortAutoMode Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    retVal = GT_NOT_SUPPORTED;

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    retVal = phySetAutoMode(dev,hwPort,&phyInfo,mode);

    gtSemGive(dev,dev->phyRegsSem);
    return retVal;

}

/*******************************************************************************
* gprtGetPortAutoMode
*
* DESCRIPTION:
*        This routine get Auto Mode of specific port.
*        Supported mode is as follows:
*        - Auto for both speed and duplex.
*        - Auto for speed only and Full duplex.
*        - Auto for speed only and Half duplex.
*        - Auto for duplex only and speed 1000Mbps.
*        - Auto for duplex only and speed 100Mbps.
*        - Auto for duplex only and speed 10Mbps.
*        - Speed 1000Mbps and Full duplex.
*        - Speed 1000Mbps and Half duplex.
*        - Speed 100Mbps and Full duplex.
*        - Speed 100Mbps and Half duplex.
*        - Speed 10Mbps and Full duplex.
*        - Speed 10Mbps and Half duplex.
*
*
* INPUTS:
*        port -    The logical port number, unless SERDES device is accessed
*                  The physical address, if SERDES device is accessed
*
* OUTPUTS:
*        mode -    Auto Mode to be written
*
* RETURNS:
*        GT_OK   - on success
*        GT_FAIL - on error
*        GT_NOT_SUPPORTED - on device without copper
*
* COMMENTS:
*         data sheet register 4.8, 4.7, 4.6, and 4.5 Autonegotiation Advertisement
*         data sheet register 4.6, 4.5 Autonegotiation Advertisement for 1000BX
*         data sheet register 9.9, 9.8 Autonegotiation Advertisement for 1000BT
*******************************************************************************/

GT_STATUS gprtGetPortAutoMode
(
    IN  GT_QD_DEV        *dev,
    IN  GT_LPORT         port,
    OUT GT_PHY_AUTO_MODE *mode
)
{
    GT_STATUS       retVal; /* Functions return value.  */
    GT_U8           hwPort; /* the physical port number */
    GT_PHY_INFO     phyInfo;

    DBG_INFO(("gprtGetPortAutoMode Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    retVal = GT_NOT_SUPPORTED;

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        DBG_INFO(("PHY device is not configurable.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    retVal = phyGetAutoMode(dev,hwPort,&phyInfo,mode);

    gtSemGive(dev,dev->phyRegsSem);
    return retVal;

}

/*******************************************************************************
* gprtSetPause
*
* DESCRIPTION:
*       This routine will set the pause bit in Autonegotiation Advertisement
*        Register. And restart the autonegotiation.
*
* INPUTS:
*        port -    The logical port number, unless SERDES device is accessed
*                The physical address, if SERDES device is accessed
*        state - GT_PHY_PAUSE_MODE enum value.
*                GT_PHY_NO_PAUSE        - disable pause
*                 GT_PHY_PAUSE        - support pause
*                GT_PHY_ASYMMETRIC_PAUSE    - support asymmetric pause
*                GT_PHY_BOTH_PAUSE    - support both pause and asymmetric pause
*
* OUTPUTS:
*       None.
*
* RETURNS:
*       GT_OK   - on success
*       GT_FAIL - on error
* COMMENTS:
* data sheet register 4.10 Autonegotiation Advertisement Register
*******************************************************************************/

GT_STATUS gprtSetPause
(
IN GT_QD_DEV *dev,
IN GT_LPORT  port,
IN GT_PHY_PAUSE_MODE state
)
{
    GT_U8           hwPort;         /* the physical port number     */
    GT_U16             u16Data,regStart;
    GT_STATUS        retVal = GT_OK;
    GT_PHY_INFO        phyInfo;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtSetPause_mad(dev, port, state);
#endif

    DBG_INFO(("phySetPause Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    regStart = 10;

    if(state & GT_PHY_ASYMMETRIC_PAUSE)
    {
        if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
        {
            DBG_INFO(("Unknown PHY device.\n"));
            gtSemGive(dev,dev->phyRegsSem);
            return GT_FAIL;
        }

        if (!(phyInfo.flag & GT_PHY_GIGABIT))
        {
            DBG_INFO(("Not Supported\n"));
            gtSemGive(dev,dev->phyRegsSem);
            return GT_BAD_PARAM;
        }

        if(!(phyInfo.flag & GT_PHY_COPPER))
        {
            regStart = 7;
        }

    }

    u16Data = state;

    /* Write to Phy AutoNegotiation Advertisement Register.  */
    if((retVal=hwSetPhyRegField(dev,hwPort,QD_PHY_AUTONEGO_AD_REG,(GT_U8)regStart,2,u16Data)) != GT_OK)
    {
        DBG_INFO(("Not able to write Phy Reg(port:%d,offset:%d).\n",hwPort,QD_PHY_AUTONEGO_AD_REG));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    /* Restart Auto Negotiation */
    if((retVal=hwSetPhyRegField(dev,hwPort,QD_PHY_CONTROL_REG,9,1,1)) != GT_OK)
    {
        DBG_INFO(("Not able to write Phy Reg(port:%d,offset:%d,data:%#x).\n",hwPort,QD_PHY_AUTONEGO_AD_REG,u16Data));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}

/*******************************************************************************
* gprtGetPause
*
* DESCRIPTION:
*       This routine will get the pause bit in Autonegotiation Advertisement
*       Register.
*
* INPUTS:
*        port -  The logical port number, unless SERDES device is accessed
*                The physical address, if SERDES device is accessed
*
*
* OUTPUTS:
*        state - GT_PHY_PAUSE_MODE enum value.
*                GT_PHY_NO_PAUSE         - disable pause
*                GT_PHY_PAUSE            - support pause
*                GT_PHY_ASYMMETRIC_PAUSE - support asymmetric pause
*                GT_PHY_BOTH_PAUSE       - support both pause and asymmetric pause
*
* RETURNS:
*       GT_OK   - on success
*       GT_FAIL - on error
* COMMENTS:
*       data sheet register 4.10 Autonegotiation Advertisement Register
*******************************************************************************/
GT_STATUS gprtGetPause
(
    IN GT_QD_DEV           *dev,
    IN GT_LPORT            port,
    OUT  GT_PHY_PAUSE_MODE *state
)
{
    GT_U8          hwPort;  /* the physical port number */
    GT_U16         u16Data;
    GT_U16         regStart;
    GT_STATUS      retVal = GT_OK;
    GT_PHY_INFO    phyInfo;

    DBG_INFO(("gprtGetPause Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    regStart = 10;

    /* Read Phy AutoNegotiation Advertisement Register.  */
    if((retVal=hwGetPhyRegField(dev,hwPort,QD_PHY_AUTONEGO_AD_REG,(GT_U8)regStart,2,&u16Data)) != GT_OK)
    {
        DBG_INFO(("Not able to write Phy Reg(port:%d,offset:%d).\n",hwPort,QD_PHY_AUTONEGO_AD_REG));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    gtSemGive(dev,dev->phyRegsSem);

    *state = u16Data;

    return retVal;
}

static
GT_STATUS dteWorkAround_Phy100M
(
    IN  GT_QD_DEV *dev,
    IN  GT_U8            hwPort
)
{
    GT_STATUS status = GT_OK;
    GT_U32 threshold[] = {0x000B,0x0000,0x8780,0x0000,0x8F80,0x0000,
                          0x9780,0x0000,0x9F80,0x0000,0xA780,0x0000,
                          0xAF80,0x0000,0xB780,0x0000,0xBF80,0x0000,
                          0xC780,0x0000,0xCF80,0x0000,0xD780,0x0000,
                          0xDF80,0x0000,0xE780,0x0000,0xEF80,0x0000,
                          0xF780,0x0000,0xFF80,0x0000};
    int i, thresholdSize;

    /* force r125 clock */
    if((status= hwWritePhyReg(dev,hwPort,0x1D,0x0003)) != GT_OK)
    {
        return status;
    }
    if((status= hwWritePhyReg(dev,hwPort,0x1E,0x807f)) != GT_OK)
    {
        return status;
    }

    /* write thresholds */
    if((status= hwWritePhyReg(dev,hwPort,0x1D,0x000B)) != GT_OK)
    {
        return status;
    }

    thresholdSize = sizeof(threshold)/sizeof(GT_U32);

    for(i=0; i<thresholdSize; i++)
    {
        if((status= hwWritePhyReg(dev,hwPort,0x1E,(GT_U16)threshold[i])) != GT_OK)
        {
            return status;
        }
    }

    /* setting adc Masking */
    if((status= hwWritePhyReg(dev,hwPort,0x1D,0x0001)) != GT_OK)
    {
        return status;
    }
    if((status= hwWritePhyReg(dev,hwPort,0x1E,0x4000)) != GT_OK)
    {
        return status;
    }

    /* setting noise level */
    if((status= hwWritePhyReg(dev,hwPort,0x1D,0x0005)) != GT_OK)
    {
        return status;
    }
    if((status= hwWritePhyReg(dev,hwPort,0x1E,0xA000)) != GT_OK)
    {
        return status;
    }

    /*
        offseting cable length measurement by 6.72m(2*4*0.84m)
        set 30_10.14:11 to 0x1001 for cable length measure.
    */
    if((status= hwWritePhyReg(dev,hwPort,0x1D,0x000a)) != GT_OK)
    {
        return status;
    }
    if((status= hwWritePhyReg(dev,hwPort,0x1E,0x4840)) != GT_OK)
    {
        return status;
    }

    /* release force r125 clock */
    if((status= hwWritePhyReg(dev,hwPort,0x1D,0x0003)) != GT_OK)
    {
        return status;
    }
    if((status= hwWritePhyReg(dev,hwPort,0x1E,0x0000)) != GT_OK)
    {
        return status;
    }


    return status;
}

static
GT_STATUS dteWorkAround_Phy1000M
(
    IN  GT_QD_DEV *dev,
    IN  GT_U8            hwPort
)
{
    GT_STATUS status = GT_OK;
    GT_U32 threshold[] = {0x0000,0x8780,0x0000,0x8F80,0x0000,0x9780,
                          0x0000,0x9F80,0x0000,0xA780,0x0000,0xAF80,
                          0x0000,0xB780,0x0000,0xBF80,0x0000,0xC780,
                          0x0000,0xCF80,0x0000,0xD780,0x0000,0xDF80,
                          0x0000,0xE780,0x0000,0xEF80,0x0000,0xF780,
                          0x0000,0xFF80,0x0000};
    int i, thresholdSize;

    /*  */
    if((status= hwWritePhyReg(dev,hwPort,0x1D,0x001B)) != GT_OK)
    {
        return status;
    }
    if((status= hwWritePhyReg(dev,hwPort,0x1E,0x43FF)) != GT_OK)
    {
        return status;
    }

    /*  */
    if((status= hwWritePhyReg(dev,hwPort,0x1D,0x001C)) != GT_OK)
    {
        return status;
    }
    if((status= hwWritePhyReg(dev,hwPort,0x1E,0x9999)) != GT_OK)
    {
        return status;
    }

    /*  */
    if((status= hwWritePhyReg(dev,hwPort,0x1D,0x001F)) != GT_OK)
    {
        return status;
    }
    if((status= hwWritePhyReg(dev,hwPort,0x1E,0xE00C)) != GT_OK)
    {
        return status;
    }

    /*  */
    if((status= hwWritePhyReg(dev,hwPort,0x1D,0x0018)) != GT_OK)
    {
        return status;
    }
    if((status= hwWritePhyReg(dev,hwPort,0x1E,0xFFA1)) != GT_OK)
    {
        return status;
    }

    /* write thresholds */
    if((status= hwWritePhyReg(dev,hwPort,0x1D,0x0010)) != GT_OK)
    {
        return status;
    }

    thresholdSize = sizeof(threshold)/sizeof(GT_U32);

    for(i=0; i<thresholdSize; i++)
    {
        if((status= hwWritePhyReg(dev,hwPort,0x1E,(GT_U16)threshold[i])) != GT_OK)
        {
            return status;
        }
    }

    return status;
}

static
GT_STATUS feSetDTE
(
    IN  GT_QD_DEV *dev,
    IN  GT_U8     hwPort,
    IN  GT_BOOL   state
)
{
    GT_U16             u16Data;
    GT_STATUS        retVal = GT_OK;

    if((retVal = hwReadPhyReg(dev,hwPort,0x10,&u16Data)) != GT_OK)
    {
        return retVal;
    }

    u16Data = state?(u16Data|0x8000):(u16Data&(~0x8000));

    if((retVal = hwWritePhyReg(dev,hwPort,0x10,u16Data)) != GT_OK)
    {
        return retVal;
    }

    /* soft reset */
    if((retVal = hwPhyReset(dev,hwPort,0xFF)) != GT_OK)
    {
        return retVal;
    }

    return retVal;
}

static
GT_STATUS gigSetDTE
(
    IN  GT_QD_DEV *dev,
    IN  GT_U8     hwPort,
    IN  GT_BOOL   state
)
{
    GT_U16             u16Data;
    GT_STATUS        retVal = GT_OK;

    if((retVal = hwReadPhyReg(dev,hwPort,20,&u16Data)) != GT_OK)
    {
        return retVal;
    }

    u16Data = state?(u16Data|0x4):(u16Data&(~0x4));

    if((retVal = hwWritePhyReg(dev,hwPort,20,u16Data)) != GT_OK)
    {
        return retVal;
    }

    /* soft reset */
    if((retVal = hwPhyReset(dev,hwPort,0xFF)) != GT_OK)
    {
        return retVal;
    }

    return retVal;
}

static
GT_STATUS gigMPSetDTE
(
    IN  GT_QD_DEV *dev,
    IN  GT_U8     hwPort,
    IN  GT_BOOL   state
)
{
    GT_U16             u16Data;
    GT_STATUS        retVal = GT_OK;

    if((retVal = hwReadPagedPhyReg(dev,hwPort,0,26,0,&u16Data)) != GT_OK)
    {
        return retVal;
    }

    u16Data = state?(u16Data|0x100):(u16Data&(~0x100));

    if((retVal = hwWritePagedPhyReg(dev,hwPort,0,26,0,u16Data)) != GT_OK)
    {
        return retVal;
    }

    /* soft reset */
    if((retVal = hwPhyReset(dev,hwPort,0xFF)) != GT_OK)
    {
        return retVal;
    }

    return retVal;
}

/*******************************************************************************
* gprtSetDTEDetect
*
* DESCRIPTION:
*       This routine enables/disables DTE.
*
* INPUTS:
*         port - The logical port number
*         mode - either GT_TRUE(for enable) or GT_FALSE(for disable)
*
* OUTPUTS:
*       None.
*
* RETURNS:
*       GT_OK   - on success
*       GT_FAIL - on error
*
* COMMENTS:
*
*******************************************************************************/

GT_STATUS gprtSetDTEDetect
(
    IN GT_QD_DEV *dev,
    IN GT_LPORT  port,
    IN GT_BOOL   state
)
{
    GT_U8           hwPort;         /* the physical port number     */
    GT_STATUS        retVal = GT_OK;
    GT_PHY_INFO    phyInfo;
    GT_BOOL            autoOn;
    GT_U16            pageReg;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtSetDTEDetect_mad(dev, port, state);
#endif

    DBG_INFO(("phySetDTE Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    /* check if the port supports DTE */
    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if (!(phyInfo.flag & GT_PHY_DTE_CAPABLE))
    {
        DBG_INFO(("Not Supported\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    switch(phyInfo.dteType)
    {
        case GT_PHY_DTE_TYPE1:
            /* FE Phy needs work-around */
            if((retVal = feSetDTE(dev,hwPort,state)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }

            if(state == GT_FALSE)
                break;

            if((retVal = dteWorkAround_Phy100M(dev,hwPort)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }
            break;
        case GT_PHY_DTE_TYPE3:
            /* Gigabit Phy with work-around required */
            if((retVal = gigSetDTE(dev,hwPort,state)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }

            if(state == GT_FALSE)
                break;

            if((retVal = dteWorkAround_Phy1000M(dev,hwPort)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }
            break;

        case GT_PHY_DTE_TYPE2:
            /* no workaround required */
            if((retVal = gigSetDTE(dev,hwPort,state)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }

            break;
        case GT_PHY_DTE_TYPE4:
            /* no workaround required */
            if(driverPagedAccessStart(dev,hwPort,phyInfo.pageType,&autoOn,&pageReg) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return GT_FAIL;
            }

            if((retVal = gigMPSetDTE(dev,hwPort,state)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }

            if(driverPagedAccessStop(dev,hwPort,phyInfo.pageType,autoOn,pageReg) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return GT_FAIL;
            }
            break;
        case GT_PHY_DTE_TYPE5:
            /* FE Phy */
            if((retVal = feSetDTE(dev,hwPort,state)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }
            break;

        default:
            gtSemGive(dev,dev->phyRegsSem);
            return GT_NOT_SUPPORTED;
    }

    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}


/*******************************************************************************
* gprtGetDTEDetectStatus
*
* DESCRIPTION:
*       This routine gets DTE status.
*
* INPUTS:
*         port - The logical port number
*
* OUTPUTS:
*       status - GT_TRUE, if link partner needs DTE power.
*                 GT_FALSE, otherwise.
*
* RETURNS:
*       GT_OK   - on success
*       GT_FAIL - on error
*
* COMMENTS:
*
*******************************************************************************/

GT_STATUS gprtGetDTEDetectStatus
(
    IN  GT_QD_DEV *dev,
    IN  GT_LPORT  port,
    OUT GT_BOOL   *state
)
{
    GT_U8           hwPort;         /* the physical port number     */
    GT_U16             u16Data,pageReg;
    GT_STATUS        retVal = GT_OK;
    GT_PHY_INFO    phyInfo;
    GT_BOOL            autoOn;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtGetDTEDetectStatus_mad(dev, port, state);
#endif

    DBG_INFO(("gprtGetDTEStatus Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    /* check if the port supports DTE */
    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if (!(phyInfo.flag & GT_PHY_DTE_CAPABLE))
    {
        DBG_INFO(("Not Supported\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    switch(phyInfo.dteType)
    {
        case GT_PHY_DTE_TYPE1:
            /* FE Phy needs work-around */
            if((retVal = hwReadPhyReg(dev,hwPort,17,&u16Data)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }
            *state = (u16Data & 0x8000)?GT_TRUE:GT_FALSE;

            break;
        case GT_PHY_DTE_TYPE2:
        case GT_PHY_DTE_TYPE3:
            if((retVal = hwReadPhyReg(dev,hwPort,27,&u16Data)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }
            *state = (u16Data & 0x10)?GT_TRUE:GT_FALSE;

            break;
        case GT_PHY_DTE_TYPE4:
            if(driverPagedAccessStart(dev,hwPort,phyInfo.pageType,&autoOn,&pageReg) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return GT_FAIL;
            }

            if((retVal = hwReadPagedPhyReg(dev,hwPort,0,17,phyInfo.anyPage,&u16Data)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }
            *state = (u16Data & 0x4)?GT_TRUE:GT_FALSE;

            if(driverPagedAccessStop(dev,hwPort,phyInfo.pageType,autoOn,pageReg) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return GT_FAIL;
            }

            break;
        default:
            gtSemGive(dev,dev->phyRegsSem);
            return GT_NOT_SUPPORTED;
    }

    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}


/*******************************************************************************
* gprtSetDTEDetectDropWait
*
* DESCRIPTION:
*       Once the PHY no longer detects that the link partner filter, the PHY
*        will wait a period of time before clearing the power over Ethernet
*        detection status bit. The wait time is 5 seconds multiplied by the
*        given value.
*
* INPUTS:
*         port - The logical port number
*       waitTime - 0 ~ 15 (unit of 4 sec.)
*
* OUTPUTS:
*        None.
*
* RETURNS:
*       GT_OK   - on success
*       GT_FAIL - on error
*
* COMMENTS:
*
*******************************************************************************/

GT_STATUS gprtSetDTEDetectDropWait
(
    IN  GT_QD_DEV *dev,
    IN  GT_LPORT  port,
    IN  GT_U16    waitTime
)
{
    GT_U8           hwPort;         /* the physical port number     */
    GT_U16             u16Data;
    GT_STATUS        retVal = GT_OK;
    GT_PHY_INFO    phyInfo;
    GT_BOOL            autoOn;
    GT_U16            pageReg;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtSetDTEDetectDropWait_mad(dev, port, waitTime);
#endif

    DBG_INFO(("gprtSetDTEDropWait Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    /* check if the port supports DTE */
    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if (!(phyInfo.flag & GT_PHY_DTE_CAPABLE))
    {
        DBG_INFO(("Not Supported\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    switch(phyInfo.dteType)
    {
        case GT_PHY_DTE_TYPE1:
            if((retVal = hwReadPhyReg(dev,hwPort,22,&u16Data)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }
            u16Data = (u16Data & ~(0xF<<12)) | ((waitTime & 0xF) << 12);

            if((retVal = hwWritePhyReg(dev,hwPort,22,u16Data)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }
            break;
        case GT_PHY_DTE_TYPE2:
        case GT_PHY_DTE_TYPE3:
            if((retVal = hwReadPhyReg(dev,hwPort,27,&u16Data)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }
            u16Data = (u16Data & ~(0xF<<5)) | ((waitTime & 0xF) << 5);

            if((retVal = hwWritePhyReg(dev,hwPort,27,u16Data)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }

            break;
        case GT_PHY_DTE_TYPE4:
            if(driverPagedAccessStart(dev,hwPort,phyInfo.pageType,&autoOn,&pageReg) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return GT_FAIL;
            }

            if((retVal = hwReadPagedPhyReg(dev,hwPort,0,26,phyInfo.anyPage,&u16Data)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }
            u16Data = (u16Data & ~(0xF<<4)) | ((waitTime & 0xF) << 4);
            if((retVal = hwWritePagedPhyReg(dev,hwPort,0,26,phyInfo.anyPage,u16Data)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }

            if(driverPagedAccessStop(dev,hwPort,phyInfo.pageType,autoOn,pageReg) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return GT_FAIL;
            }

            break;
        default:
            gtSemGive(dev,dev->phyRegsSem);
            return GT_NOT_SUPPORTED;
    }

    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}


/*******************************************************************************
* gprtGetDTEDetectDropWait
*
* DESCRIPTION:
*       Once the PHY no longer detects that the link partner filter, the PHY
*        will wait a period of time before clearing the power over Ethernet
*        detection status bit. The wait time is 5 seconds multiplied by the
*        returned value.
*
* INPUTS:
*         port - The logical port number
*
* OUTPUTS:
*       waitTime - 0 ~ 15 (unit of 4 sec.)
*
* RETURNS:
*       GT_OK   - on success
*       GT_FAIL - on error
*
* COMMENTS:
*
*******************************************************************************/

GT_STATUS gprtGetDTEDetectDropWait
(
    IN  GT_QD_DEV *dev,
    IN  GT_LPORT  port,
    OUT GT_U16    *waitTime
)
{
    GT_U8           hwPort;         /* the physical port number     */
    GT_U16             u16Data;
    GT_STATUS        retVal = GT_OK;
    GT_PHY_INFO    phyInfo;
    GT_BOOL            autoOn;
    GT_U16            pageReg;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtGetDTEDetectDropWait_mad(dev, port, waitTime);
#endif

    DBG_INFO(("gprtSetDTEDropWait Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if (!(phyInfo.flag & GT_PHY_DTE_CAPABLE))
    {
        DBG_INFO(("Not Supported\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    switch(phyInfo.dteType)
    {
        case GT_PHY_DTE_TYPE1:
            if((retVal = hwReadPhyReg(dev,hwPort,22,&u16Data)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }
            u16Data = (u16Data >> 12) & 0xF;

            break;
        case GT_PHY_DTE_TYPE2:
        case GT_PHY_DTE_TYPE3:
            if((retVal = hwReadPhyReg(dev,hwPort,27,&u16Data)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }
            u16Data = (u16Data >> 5) & 0xF;

            break;
        case GT_PHY_DTE_TYPE4:
            if(driverPagedAccessStart(dev,hwPort,phyInfo.pageType,&autoOn,&pageReg) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return GT_FAIL;
            }

            if((retVal = hwReadPagedPhyReg(dev,hwPort,0,26,phyInfo.anyPage,&u16Data)) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return retVal;
            }
            u16Data = (u16Data >> 4) & 0xF;

            if(driverPagedAccessStop(dev,hwPort,phyInfo.pageType,autoOn,pageReg) != GT_OK)
            {
                gtSemGive(dev,dev->phyRegsSem);
                return GT_FAIL;
            }
            break;
        default:
            gtSemGive(dev,dev->phyRegsSem);
            return GT_NOT_SUPPORTED;
    }

    *waitTime = u16Data;

    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}


/*******************************************************************************
* gprtSetEnergyDetect
*
* DESCRIPTION:
*       Energy Detect power down mode enables or disables the PHY to wake up on
*        its own by detecting activity on the CAT 5 cable.
*
* INPUTS:
*         port - The logical port number
*         mode - GT_EDETECT_MODE type
*
* OUTPUTS:
*        None.
*
* RETURNS:
*       GT_OK   - on success
*       GT_FAIL - on error
*        GT_BAD_PARAM - if invalid parameter is given
*       GT_NOT_SUPPORTED - if current device does not support this feature.
*
* COMMENTS:
*
*******************************************************************************/

GT_STATUS gprtSetEnergyDetect
(
    IN  GT_QD_DEV *dev,
    IN  GT_LPORT  port,
    IN  GT_EDETECT_MODE   mode
)
{
    GT_U8           hwPort;         /* the physical port number     */
    GT_U16             u16Data;
    GT_STATUS        retVal = GT_OK;
    GT_PHY_INFO    phyInfo;
    GT_BOOL            autoOn;
    GT_U16            pageReg;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtSetEnergyDetect_mad(dev, port, mode);
#endif

    DBG_INFO(("gprtSetEnergyDetect Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if (phyInfo.flag & GT_PHY_SERDES_CORE)
    {
        DBG_INFO(("Not Supported.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }
    else if (phyInfo.flag & GT_PHY_GIGABIT)
    {
        /* check if the mode is valid */
        switch (mode)
        {
            case GT_EDETECT_OFF:
                u16Data = 0;
                break;
            case GT_EDETECT_SENSE_PULSE:
                u16Data = 3;
                break;
            case GT_EDETECT_SENSE:
                u16Data = 2;
                break;
            default:
                DBG_INFO(("Invalid paramerter.\n"));
                gtSemGive(dev,dev->phyRegsSem);
                return GT_BAD_PARAM;
        }

        if(driverPagedAccessStart(dev,hwPort,phyInfo.pageType,&autoOn,&pageReg) != GT_OK)
        {
            gtSemGive(dev,dev->phyRegsSem);
            return GT_FAIL;
        }

        if((retVal = hwSetPagedPhyRegField(dev,hwPort,0,0x10,8,2,phyInfo.anyPage,u16Data)) != GT_OK)
        {
            gtSemGive(dev,dev->phyRegsSem);
            return retVal;
        }

        if((retVal = hwPhyReset(dev,hwPort,0xFF)) != GT_OK)
        {
            gtSemGive(dev,dev->phyRegsSem);
            return retVal;
        }

        if(driverPagedAccessStop(dev,hwPort,phyInfo.pageType,autoOn,pageReg) != GT_OK)
        {
            gtSemGive(dev,dev->phyRegsSem);
            return GT_FAIL;
        }
    }
    else    /* it's a Fast Ethernet device */
    {
        /* check if the mode is valid */
        switch (mode)
        {
            case GT_EDETECT_OFF:
                u16Data = 0;
                break;
            case GT_EDETECT_SENSE_PULSE:
                u16Data = 1;
                break;
            case GT_EDETECT_SENSE:
            default:
                DBG_INFO(("Invalid paramerter.\n"));
                gtSemGive(dev,dev->phyRegsSem);
                return GT_BAD_PARAM;
        }

        if((retVal = hwSetPhyRegField(dev,hwPort,0x10,14,1,u16Data)) != GT_OK)
        {
            gtSemGive(dev,dev->phyRegsSem);
            return retVal;
        }
    }

    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}


/*******************************************************************************
* gprtGetEnergyDetect
*
* DESCRIPTION:
*       Energy Detect power down mode enables or disables the PHY to wake up on
*        its own by detecting activity on the CAT 5 cable.
*
* INPUTS:
*         port - The logical port number
*
* OUTPUTS:
*       mode - GT_EDETECT_MODE type
*
* RETURNS:
*       GT_OK   - on success
*       GT_FAIL - on error
*       GT_NOT_SUPPORTED - if current device does not support this feature.
*
* COMMENTS:
*
*******************************************************************************/

GT_STATUS gprtGetEnergyDetect
(
    IN  GT_QD_DEV *dev,
    IN  GT_LPORT  port,
    OUT GT_EDETECT_MODE   *mode
)
{
    GT_U8           hwPort;         /* the physical port number     */
    GT_U16             u16Data;
    GT_STATUS        retVal = GT_OK;
    GT_PHY_INFO    phyInfo;
    GT_BOOL            autoOn;
    GT_U16            pageReg;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtGetEnergyDetect_mad(dev, port, mode);
#endif

    DBG_INFO(("gprtGetEnergyDetect Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if (phyInfo.flag & GT_PHY_SERDES_CORE)
    {
        DBG_INFO(("Not Supported.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }
    else if (phyInfo.flag & GT_PHY_GIGABIT)
    {
        /* read the mode */

        if(driverPagedAccessStart(dev,hwPort,phyInfo.pageType,&autoOn,&pageReg) != GT_OK)
        {
            gtSemGive(dev,dev->phyRegsSem);
            return GT_FAIL;
        }

        if((retVal = hwGetPagedPhyRegField(dev,hwPort,0,0x10,8,2,phyInfo.anyPage,&u16Data)) != GT_OK)
        {
            gtSemGive(dev,dev->phyRegsSem);
            return retVal;
        }

        if(driverPagedAccessStop(dev,hwPort,phyInfo.pageType,autoOn,pageReg) != GT_OK)
        {
            gtSemGive(dev,dev->phyRegsSem);
            return GT_FAIL;
        }

        switch (u16Data)
        {
            case 0:
            case 1:
                *mode = GT_EDETECT_OFF;
                break;
            case 2:
                *mode = GT_EDETECT_SENSE;
                break;
            case 3:
                *mode = GT_EDETECT_SENSE_PULSE;
                break;
            default:
                DBG_INFO(("Unknown value (shouldn't happen).\n"));
                gtSemGive(dev,dev->phyRegsSem);
                return GT_FAIL;
        }

    }
    else    /* it's a Fast Ethernet device */
    {
        /* read the mode */
        if((retVal = hwGetPhyRegField(dev,hwPort,0x10,14,1,&u16Data)) != GT_OK)
        {
            gtSemGive(dev,dev->phyRegsSem);
            return retVal;
        }

        switch (u16Data)
        {
            case 0:
                *mode = GT_EDETECT_OFF;
                break;
            case 1:
                *mode = GT_EDETECT_SENSE_PULSE;
                break;
            default:
                DBG_INFO(("Unknown value (shouldn't happen).\n"));
                gtSemGive(dev,dev->phyRegsSem);
                return GT_FAIL;
        }

    }


    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}


/*******************************************************************************
* gprtSet1000TMasterMode
*
* DESCRIPTION:
*       This routine sets the ports 1000Base-T Master mode and restart the Auto
*        negotiation.
*
* INPUTS:
*       port - the logical port number.
*       mode - GT_1000T_MASTER_SLAVE structure
*                autoConfig   - GT_TRUE for auto, GT_FALSE for manual setup.
*                masterPrefer - GT_TRUE if Master configuration is preferred.
*
* OUTPUTS:
*       None.
*
* RETURNS:
*       GT_OK   - on success
*       GT_FAIL - on error
*
* COMMENTS:
*
*
* GalTis:
*
*******************************************************************************/
GT_STATUS gprtSet1000TMasterMode
(
    IN  GT_QD_DEV   *dev,
    IN  GT_LPORT     port,
    IN  GT_1000T_MASTER_SLAVE   *mode
)
{
    GT_STATUS    retVal;         /* Functions return value.      */
    GT_U8            hwPort;         /* the physical port number     */
    GT_U16        data;
    GT_PHY_INFO    phyInfo;
    GT_BOOL            autoOn;
    GT_U16            pageReg;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtSet1000TMasterMode_mad(dev, port, mode);
#endif

    DBG_INFO(("gprtSet1000TMasterMode Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    if (!IS_IN_DEV_GROUP(dev,DEV_GIGABIT_SWITCH))
    {
        return GT_NOT_SUPPORTED;
    }

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if (!(phyInfo.flag & GT_PHY_GIGABIT) || !(phyInfo.flag & GT_PHY_COPPER))
    {
        DBG_INFO(("Not Supported\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(mode->autoConfig == GT_TRUE)
    {
        if(mode->masterPrefer == GT_TRUE)
        {
            data = 0x1;
        }
        else
        {
            data = 0x0;
        }
    }
    else
    {
        if(mode->masterPrefer == GT_TRUE)
        {
            data = 0x6;
        }
        else
        {
            data = 0x4;
        }
    }

    if(driverPagedAccessStart(dev,hwPort,phyInfo.pageType,&autoOn,&pageReg) != GT_OK)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    /* Set the Master Mode.    */
    retVal = hwSetPagedPhyRegField(dev,hwPort,0,9,10,3,phyInfo.anyPage,data);
    if(retVal != GT_OK)
    {
        DBG_INFO(("Failed.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return retVal;
    }
    else
    {
        DBG_INFO(("OK.\n"));
    }

    /* Restart Auto Negotiation */
    if((retVal=hwSetPhyRegField(dev,hwPort,QD_PHY_CONTROL_REG,9,1,1)) != GT_OK)
    {
        DBG_INFO(("Not able to write Phy Reg(port:%d,offset:%d,data:%#x).\n",hwPort,QD_PHY_CONTROL_REG,1));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if(driverPagedAccessStop(dev,hwPort,phyInfo.pageType,autoOn,pageReg) != GT_OK)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}


/*******************************************************************************
* gprtGet1000TMasterMode
*
* DESCRIPTION:
*       This routine retrieves 1000Base-T Master Mode
*
* INPUTS:
*       port - the logical port number.
*
* OUTPUTS:
*       mode - GT_1000T_MASTER_SLAVE structure
*                autoConfig   - GT_TRUE for auto, GT_FALSE for manual setup.
*                masterPrefer - GT_TRUE if Master configuration is preferred.
*
* RETURNS:
*       GT_OK   - on success
*       GT_FAIL - on error
*
* COMMENTS:
*
*
* GalTis:
*
*******************************************************************************/
GT_STATUS gprtGet1000TMasterMode
(
    IN  GT_QD_DEV   *dev,
    IN  GT_LPORT     port,
    OUT GT_1000T_MASTER_SLAVE   *mode
)
{
    GT_STATUS    retVal;         /* Functions return value.      */
    GT_U8            hwPort;         /* the physical port number     */
    GT_U16        data;
    GT_PHY_INFO    phyInfo;
    GT_BOOL            autoOn;
    GT_U16            pageReg;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtGet1000TMasterMode_mad(dev, port, mode);
#endif

    DBG_INFO(("gprtGet1000TMasterMode Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    if (!IS_IN_DEV_GROUP(dev,DEV_GIGABIT_SWITCH))
    {
        return GT_NOT_SUPPORTED;
    }

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if (!(phyInfo.flag & GT_PHY_GIGABIT) || !(phyInfo.flag & GT_PHY_COPPER))
    {
        DBG_INFO(("Not Supported\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverPagedAccessStart(dev,hwPort,phyInfo.pageType,&autoOn,&pageReg) != GT_OK)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    /* Set the Master Mode.    */
    retVal = hwGetPagedPhyRegField(dev,hwPort,0,9,10,3,phyInfo.anyPage,&data);
    if(retVal != GT_OK)
    {
        DBG_INFO(("Failed.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return retVal;
    }
    else
    {
        DBG_INFO(("OK.\n"));
    }

    if(driverPagedAccessStop(dev,hwPort,phyInfo.pageType,autoOn,pageReg) != GT_OK)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if(data & 0x4)    /* Manual Mode */
    {
        mode->autoConfig = GT_FALSE;

        if(data & 0x2)
        {
            mode->masterPrefer = GT_TRUE;
        }
        else
        {
            mode->masterPrefer = GT_FALSE;
        }
    }
    else    /* Auto Mode */
    {
        mode->autoConfig = GT_TRUE;

        if(data & 0x1)
        {
            mode->masterPrefer = GT_TRUE;
        }
        else
        {
            mode->masterPrefer = GT_FALSE;
        }
    }

    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}

/*******************************************************************************
* gprtGetPhyLinkStatus
*
* DESCRIPTION:
*       This routine retrieves the Link status.
*
* INPUTS:
*        port -    The logical port number, unless SERDES device is accessed
*                The physical address, if SERDES device is accessed
*
* OUTPUTS:
*       linkStatus - GT_FALSE if link is not established,
*                     GT_TRUE if link is established.
*
* RETURNS:
*       GT_OK   - on success
*       GT_FAIL - on error
*
*
* COMMENTS:
*
*******************************************************************************/
GT_STATUS gprtGetPhyLinkStatus
(
    IN GT_QD_DEV *dev,
    IN GT_LPORT  port,
    IN GT_BOOL      *linkStatus
)
{

    GT_STATUS       retVal;         /* Functions return value.      */
    GT_U8           hwPort;         /* the physical port number     */
    GT_U16             u16Data;
    GT_PHY_INFO        phyInfo;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtGetPhyLinkStatus_mad(dev, port, linkStatus);
#endif

    DBG_INFO(("gprtGetPhyLinkStatus Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
         return GT_NOT_SUPPORTED;
    }

    if((retVal=hwGetPhyRegField(dev,hwPort,17,10,1,&u16Data)) != GT_OK)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return retVal;
    }

    BIT_2_BOOL(u16Data,*linkStatus);

    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}


/*******************************************************************************
* gprtSetPktGenEnable
*
* DESCRIPTION:
*       This routine enables or disables Packet Generator.
*       Link should be established first prior to enabling the packet generator,
*       and generator will generate packets at the speed of the established link.
*        When enables packet generator, the following information should be
*       provided:
*           Payload Type:  either Random or 5AA55AA5
*           Packet Length: either 64 or 1514 bytes
*           Error Packet:  either Error packet or normal packet
*
* INPUTS:
*        port -    The logical port number, unless SERDES device is accessed
*                The physical address, if SERDES device is accessed
*       en      - GT_TRUE to enable, GT_FALSE to disable
*       pktInfo - packet information(GT_PG structure pointer), if en is GT_TRUE.
*                 ignored, if en is GT_FALSE
*
* OUTPUTS:
*       None.
*
* RETURNS:
*       GT_OK   - on success
*       GT_FAIL - on error
*
*
* COMMENTS:
*
*******************************************************************************/
GT_STATUS gprtSetPktGenEnable
(
    IN GT_QD_DEV *dev,
    IN GT_LPORT  port,
    IN GT_BOOL   en,
    IN GT_PG     *pktInfo
)
{

    GT_STATUS       retVal;         /* Functions return value.      */
    GT_U8           hwPort;         /* the physical port number     */
    GT_U16             data;
    GT_BOOL            link;
    GT_PHY_INFO        phyInfo;
    GT_U8            page,reg, offset, len;
    GT_BOOL            autoOn;
    GT_U16            pageReg;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtSetPktGenEnable_mad(dev, port, en, pktInfo);
#endif

    DBG_INFO(("gprtSetPktGenEnable Called.\n"));

    /* translate LPORT to hardware port */
    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if(!(phyInfo.flag & GT_PHY_PKT_GENERATOR))
    {
        DBG_INFO(("Not Supported.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    switch (phyInfo.pktGenType)
    {
        case GT_PHY_PKTGEN_TYPE1:    /* 30_18.5:2 */
                page = 18;
                reg = 30;
                offset = 2;
                break;
        case GT_PHY_PKTGEN_TYPE2:    /* 16_6.3:0 */
                page = 6;
                reg = 16;
                offset = 0;
                break;
        case GT_PHY_PKTGEN_TYPE3:    /* 25.3:0 */
                page = 0;
                reg = 25;
                offset = 0;
                break;
        default:
                DBG_INFO(("Unknown PKTGEN Type.\n"));
                gtSemGive(dev,dev->phyRegsSem);
                return GT_FAIL;
    }

    if (en)
    {
        if((retVal = gprtGetPhyLinkStatus(dev,port,&link)) != GT_OK)
        {
            gtSemGive(dev,dev->phyRegsSem);
            return GT_FAIL;
        }

        if (link == GT_FALSE)
        {
            DBG_INFO(("Link should be on to run Packet Generator.\n"));
            gtSemGive(dev,dev->phyRegsSem);
            return GT_FAIL;
        }

        data = 0x8;

        if (pktInfo->payload == GT_PG_PAYLOAD_5AA5)
            data |= 0x4;

        if (pktInfo->length == GT_PG_LENGTH_1514)
            data |= 0x2;

        if (pktInfo->tx == GT_PG_TX_ERROR)
            data |= 0x1;

        len = 4;
    }
    else
    {
        data = 0;
        len = 1;
        offset += 3;
    }

    if(driverPagedAccessStart(dev,hwPort,phyInfo.pageType,&autoOn,&pageReg) != GT_OK)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if((retVal=hwSetPagedPhyRegField(dev,hwPort,
                page,reg,offset,len,phyInfo.anyPage,data)) != GT_OK)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return retVal;
    }

    if(driverPagedAccessStop(dev,hwPort,phyInfo.pageType,autoOn,pageReg) != GT_OK)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    gtSemGive(dev,dev->phyRegsSem);
    return retVal;
}


/*******************************************************************************
* gprtGetPhyReg
*
* DESCRIPTION:
*       This routine reads Phy Registers.
*
* INPUTS:
*       port -    The logical port number,
*       regAddr - The register's address.
*
* OUTPUTS:
*       data    - The read register's data.
*
* RETURNS:
*       GT_OK           - on success
*       GT_FAIL         - on error
*
* COMMENTS:
*       None.
*
* GalTis:
*
*******************************************************************************/
GT_STATUS gprtGetPhyReg
(
    IN  GT_QD_DEV    *dev,
    IN  GT_LPORT     port,
    IN  GT_U32         regAddr,
    OUT GT_U16         *data
)
{
    GT_U16          u16Data;           /* The register's read data.    */
    GT_U8           hwPort;         /* the physical port number     */

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtGetPhyReg_mad(dev, port, regAddr, data);
#endif

    DBG_INFO(("gprtGetPhyReg Called.\n"));

/*    hwPort = GT_LPORT_2_PHY(port); */
    hwPort = qdLong2Char(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* Get Phy Register. */
    if(hwReadPhyReg(dev,hwPort,(GT_U8)regAddr,&u16Data) != GT_OK)
    {
        DBG_INFO(("Failed.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    *data = u16Data;

    gtSemGive(dev,dev->phyRegsSem);
    return GT_OK;
}

/*******************************************************************************
* gprtSetPhyReg
*
* DESCRIPTION:
*       This routine writes Phy Registers.
*
* INPUTS:
*       port -    The logical port number,
*       regAddr - The register's address.
*
* OUTPUTS:
*       data    - The read register's data.
*
* RETURNS:
*       GT_OK           - on success
*       GT_FAIL         - on error
*
* COMMENTS:
*       None.
*
* GalTis:
*
*******************************************************************************/
GT_STATUS gprtSetPhyReg
(
    IN  GT_QD_DEV        *dev,
    IN  GT_LPORT         port,
    IN  GT_U32           regAddr,
    IN  GT_U16           data
)
{
    GT_U8           hwPort;         /* the physical port number     */

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtSetPhyReg_mad(dev, port, regAddr, data);
#endif

    DBG_INFO(("gprtSetPhyReg Called.\n"));

/*    hwPort = GT_LPORT_2_PHY(port); */
    hwPort = qdLong2Char(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* Write to Phy Register */
    if(hwWritePhyReg(dev,hwPort,(GT_U8)regAddr,data) != GT_OK)
    {
        DBG_INFO(("Failed.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    gtSemGive(dev,dev->phyRegsSem);
    return GT_OK;
}


/*******************************************************************************
* gprtGetPagedPhyReg
*
* DESCRIPTION:
*       This routine reads phy register of the given page
*
* INPUTS:
*        port     - logical port to be read
*        regAddr    - register offset to be read
*        page    - page number to be read
*
* OUTPUTS:
*        data    - value of the read register
*
* RETURNS:
*       GT_OK               - if read successed
*       GT_FAIL               - if read failed
*
* COMMENTS:
*       None.
*
*******************************************************************************/
GT_STATUS gprtGetPagedPhyReg
(
    IN  GT_QD_DEV *dev,
    IN  GT_U32  port,
    IN    GT_U32  regAddr,
    IN    GT_U32  page,
    OUT GT_U16* data
)
{
    GT_PHY_INFO        phyInfo;
    GT_BOOL            autoOn;
    GT_U16            pageReg;
    GT_U8            hwPort;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtGetPagedPhyReg_mad(dev, port, regAddr, page, data);
#endif

    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if(driverPagedAccessStart(dev,hwPort,phyInfo.pageType,&autoOn,&pageReg) != GT_OK)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if(hwReadPagedPhyReg(dev,hwPort,(GT_U8)page,
                                (GT_U8)regAddr,0,data) != GT_OK)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if(driverPagedAccessStop(dev,hwPort,phyInfo.pageType,autoOn,pageReg) != GT_OK)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    gtSemGive(dev,dev->phyRegsSem);
    return GT_OK;
}

/*******************************************************************************
* gprtSetPagedPhyReg
*
* DESCRIPTION:
*       This routine writes a value to phy register of the given page
*
* INPUTS:
*        port     - logical port to be read
*        regAddr    - register offset to be read
*        page    - page number to be read
*        data    - value of the read register
*
* OUTPUTS:
*        None
*
* RETURNS:
*       GT_OK               - if read successed
*       GT_FAIL               - if read failed
*
* COMMENTS:
*       None.
*
*******************************************************************************/
GT_STATUS gprtSetPagedPhyReg
(
    IN  GT_QD_DEV *dev,
    IN  GT_U32 port,
    IN    GT_U32 regAddr,
    IN    GT_U32 page,
    IN  GT_U16 data
)
{
    GT_PHY_INFO        phyInfo;
    GT_BOOL            autoOn;
    GT_U16            pageReg;
    GT_U8            hwPort;

#ifdef GT_USE_MAD
    if (dev->use_mad==GT_TRUE)
        return gprtSetPagedPhyReg_mad(dev, port, regAddr, page, data);
#endif

    hwPort = GT_LPORT_2_PHY(port);

    gtSemTake(dev,dev->phyRegsSem,OS_WAIT_FOREVER);

    /* check if the port is configurable */
    if((phyInfo.phyId=GT_GET_PHY_ID(dev,hwPort)) == GT_INVALID_PHY)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_NOT_SUPPORTED;
    }

    if(driverFindPhyInformation(dev,hwPort,&phyInfo) != GT_OK)
    {
        DBG_INFO(("Unknown PHY device.\n"));
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if(driverPagedAccessStart(dev,hwPort,phyInfo.pageType,&autoOn,&pageReg) != GT_OK)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if(hwWritePagedPhyReg(dev,hwPort,(GT_U8)page,
                                (GT_U8)regAddr,0,data) != GT_OK)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    if(driverPagedAccessStop(dev,hwPort,phyInfo.pageType,autoOn,pageReg) != GT_OK)
    {
        gtSemGive(dev,dev->phyRegsSem);
        return GT_FAIL;
    }

    gtSemGive(dev,dev->phyRegsSem);
    return GT_OK;
}