blob: 958b19ad30326fe1b7fbff7769dde6abb919da67 [file] [log] [blame]
/*
* Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
*
* Copyright (C) 2008 Lyrtech <www.lyrtech.com>
* Copyright (C) 2008 Philip Balister, OpenSDR <philip@opensdr.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* Board */
#define SFFSDR
#define CONFIG_SYS_NAND_LARGEPAGE
#define CONFIG_SYS_USE_NAND
#define CONFIG_SYS_USE_DSPLINK /* don't power up the DSP. */
/* SoC Configuration */
#define CONFIG_ARM926EJS /* arm926ejs CPU core */
#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */
#define CONFIG_SYS_HZ_CLOCK 27000000 /* Timer Input clock freq */
#define CONFIG_SYS_HZ 1000
#define CONFIG_SOC_DM644X
/* EEPROM definitions for Atmel 24LC64 EEPROM chip */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
/* Memory Info */
#define CONFIG_SYS_MALLOC_LEN (0x10000 + 256*1024) /* malloc() len */
#define CONFIG_SYS_MEMTEST_START 0x80000000 /* memtest start address */
#define CONFIG_SYS_MEMTEST_END 0x81000000 /* 16MB RAM test */
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
#define PHYS_SDRAM_1 0x80000000 /* DDR Start */
#define PHYS_SDRAM_1_SIZE 0x08000000 /* DDR size 128MB */
#define DDR_4BANKS /* 4-bank DDR2 (128MB) */
/* Serial Driver info */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size, byteorder */
#define CONFIG_SYS_NS16550_COM1 0x01c20000 /* Base address of UART0 */
#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_HZ_CLOCK /* Input clock to NS16550 */
#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
#define CONFIG_BAUDRATE 115200 /* Default baud rate */
/* I2C Configuration */
#define CONFIG_HARD_I2C
#define CONFIG_DRIVER_DAVINCI_I2C
#define CONFIG_SYS_I2C_SPEED 80000 /* 100Kbps won't work, silicon bug */
#define CONFIG_SYS_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
/* Network & Ethernet Configuration */
#define CONFIG_DRIVER_TI_EMAC
#define CONFIG_MII
#define CONFIG_BOOTP_DEFAULT
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_NET_RETRY_COUNT 10
#define CONFIG_OVERWRITE_ETHADDR_ONCE
/* Flash & Environment */
#undef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_SYS_NO_FLASH
#define CONFIG_NAND_DAVINCI
#define CONFIG_SYS_NAND_CS 2
#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
#define CONFIG_ENV_SECT_SIZE 2048 /* Env sector Size */
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
#define CONFIG_SYS_NAND_BASE 0x02000000
#define CONFIG_SYS_NAND_HW_ECC
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
/* I2C switch definitions for PCA9543 chip */
#define CONFIG_SYS_I2C_PCA9543_ADDR 0x70
#define CONFIG_SYS_I2C_PCA9543_ADDR_LEN 0 /* Single register. */
#define CONFIG_SYS_I2C_PCA9543_ENABLE_CH0 0x01 /* Enable channel 0. */
/* U-Boot general configuration */
#define CONFIG_MISC_INIT_R
#define CONFIG_BOOTDELAY 5 /* Autoboot after 5 seconds. */
#define CONFIG_BOOTFILE "uImage" /* Boot file name */
#define CONFIG_SYS_PROMPT "U-Boot > " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE \
(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print buffer size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* Default Linux kernel
* load address. */
#define CONFIG_VERSION_VARIABLE
#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far,
* may be later */
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_LONGHELP
#define CONFIG_CRC32_VERIFY
#define CONFIG_MX_CYCLIC
/* Linux Information */
#define LINUX_BOOT_PARAM_ADDR 0x80000100
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_BOOTARGS \
"mem=56M " \
"console=ttyS0,115200n8 " \
"root=/dev/nfs rw noinitrd ip=dhcp " \
"nfsroot=${serverip}:/nfsroot/sffsdr " \
"eth0=${ethaddr}"
#define CONFIG_BOOTCOMMAND \
"nand read 87A00000 100000 300000;" \
"bootelf 87A00000"
/* U-Boot commands */
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_SAVES
#define CONFIG_CMD_NAND
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_ELF /* Needed to load Integrity kernel. */
#undef CONFIG_CMD_BDI
#undef CONFIG_CMD_FPGA
#undef CONFIG_CMD_SETGETDCR
#undef CONFIG_CMD_FLASH
#undef CONFIG_CMD_IMLS
#ifdef CONFIG_CMD_BDI
#define CONFIG_CLOCKS
#endif
#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \
CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
#endif /* __CONFIG_H */