blob: 29720658225594c3a422c2470e59c433716b939d [file] [log] [blame]
/*
* Copyright (C) 2008, Guennadi Liakhovetski <lg@denx.de>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <asm/arch/imx-regs.h>
.macro REG reg, val
ldr r2, =\reg
ldr r3, =\val
str r3, [r2]
.endm
.macro REG8 reg, val
ldr r2, =\reg
ldr r3, =\val
strb r3, [r2]
.endm
.macro DELAY loops
ldr r2, =\loops
1:
subs r2, r2, #1
nop
bcs 1b
.endm
/* RedBoot: AIPS setup - Only setup MPROTx registers.
* The PACR default values are good.*/
.macro init_aips
/*
* Set all MPROTx to be non-bufferable, trusted for R/W,
* not forced to user-mode.
*/
ldr r0, =0x43F00000
ldr r1, =0x77777777
str r1, [r0, #0x00]
str r1, [r0, #0x04]
ldr r0, =0x53F00000
str r1, [r0, #0x00]
str r1, [r0, #0x04]
/*
* Clear the on and off peripheral modules Supervisor Protect bit
* for SDMA to access them. Did not change the AIPS control registers
* (offset 0x20) access type
*/
ldr r0, =0x43F00000
ldr r1, =0x0
str r1, [r0, #0x40]
str r1, [r0, #0x44]
str r1, [r0, #0x48]
str r1, [r0, #0x4C]
ldr r1, [r0, #0x50]
and r1, r1, #0x00FFFFFF
str r1, [r0, #0x50]
ldr r0, =0x53F00000
ldr r1, =0x0
str r1, [r0, #0x40]
str r1, [r0, #0x44]
str r1, [r0, #0x48]
str r1, [r0, #0x4C]
ldr r1, [r0, #0x50]
and r1, r1, #0x00FFFFFF
str r1, [r0, #0x50]
.endm /* init_aips */
/* RedBoot: MAX (Multi-Layer AHB Crossbar Switch) setup */
.macro init_max
ldr r0, =0x43F04000
/* MPR - priority is M4 > M2 > M3 > M5 > M0 > M1 */
ldr r1, =0x00302154
str r1, [r0, #0x000] /* for S0 */
str r1, [r0, #0x100] /* for S1 */
str r1, [r0, #0x200] /* for S2 */
str r1, [r0, #0x300] /* for S3 */
str r1, [r0, #0x400] /* for S4 */
/* SGPCR - always park on last master */
ldr r1, =0x10
str r1, [r0, #0x010] /* for S0 */
str r1, [r0, #0x110] /* for S1 */
str r1, [r0, #0x210] /* for S2 */
str r1, [r0, #0x310] /* for S3 */
str r1, [r0, #0x410] /* for S4 */
/* MGPCR - restore default values */
ldr r1, =0x0
str r1, [r0, #0x800] /* for M0 */
str r1, [r0, #0x900] /* for M1 */
str r1, [r0, #0xA00] /* for M2 */
str r1, [r0, #0xB00] /* for M3 */
str r1, [r0, #0xC00] /* for M4 */
str r1, [r0, #0xD00] /* for M5 */
.endm /* init_max */
/* RedBoot: M3IF setup */
.macro init_m3if
/* Configure M3IF registers */
ldr r1, =0xB8003000
/*
* M3IF Control Register (M3IFCTL)
* MRRP[0] = L2CC0 not on priority list (0 << 0) = 0x00000000
* MRRP[1] = L2CC1 not on priority list (0 << 0) = 0x00000000
* MRRP[2] = MBX not on priority list (0 << 0) = 0x00000000
* MRRP[3] = MAX1 not on priority list (0 << 0) = 0x00000000
* MRRP[4] = SDMA not on priority list (0 << 0) = 0x00000000
* MRRP[5] = MPEG4 not on priority list (0 << 0) = 0x00000000
* MRRP[6] = IPU1 on priority list (1 << 6) = 0x00000040
* MRRP[7] = IPU2 not on priority list (0 << 0) = 0x00000000
* ------------
* 0x00000040
*/
ldr r0, =0x00000040
str r0, [r1] /* M3IF control reg */
.endm /* init_m3if */
/* RedBoot: To support 133MHz DDR */
.macro init_drive_strength
/*
* Disable maximum drive strength SDRAM/DDR lines by clearing DSE1 bits
* in SW_PAD_CTL registers
*/
/* SDCLK */
ldr r1, =0x43FAC200
ldr r0, [r1, #0x6C]
bic r0, r0, #(1 << 12)
str r0, [r1, #0x6C]
/* CAS */
ldr r0, [r1, #0x70]
bic r0, r0, #(1 << 22)
str r0, [r1, #0x70]
/* RAS */
ldr r0, [r1, #0x74]
bic r0, r0, #(1 << 2)
str r0, [r1, #0x74]
/* CS2 (CSD0) */
ldr r0, [r1, #0x7C]
bic r0, r0, #(1 << 22)
str r0, [r1, #0x7C]
/* DQM3 */
ldr r0, [r1, #0x84]
bic r0, r0, #(1 << 22)
str r0, [r1, #0x84]
/* DQM2, DQM1, DQM0, SD31-SD0, A25-A0, MA10 (0x288..0x2DC) */
ldr r2, =22 /* (0x2E0 - 0x288) / 4 = 22 */
pad_loop:
ldr r0, [r1, #0x88]
bic r0, r0, #(1 << 22)
bic r0, r0, #(1 << 12)
bic r0, r0, #(1 << 2)
str r0, [r1, #0x88]
add r1, r1, #4
subs r2, r2, #0x1
bne pad_loop
.endm /* init_drive_strength */
/* CPLD on CS4 setup */
.macro init_cs4
ldr r0, =WEIM_BASE
ldr r1, =0x0000D843
str r1, [r0, #0x40]
ldr r1, =0x22252521
str r1, [r0, #0x44]
ldr r1, =0x22220A00
str r1, [r0, #0x48]
.endm /* init_cs4 */
.globl lowlevel_init
lowlevel_init:
/* Redboot initializes very early AIPS, what for?
* Then it also initializes Multi-Layer AHB Crossbar Switch,
* M3IF */
/* Also setup the Peripheral Port Remap register inside the core */
ldr r0, =0x40000015 /* start from AIPS 2GB region */
mcr p15, 0, r0, c15, c2, 4
init_aips
init_max
init_m3if
init_drive_strength
init_cs4
/* Image Processing Unit: */
/* Too early to switch display on? */
REG IPU_CONF, IPU_CONF_DI_EN /* Switch on Display Interface */
/* Clock Control Module: */
REG CCM_CCMR, 0x074B0BF5 /* Use CKIH, MCU PLL off */
DELAY 0x40000
REG CCM_CCMR, 0x074B0BF5 | CCMR_MPE /* MCU PLL on */
REG CCM_CCMR, (0x074B0BF5 | CCMR_MPE) & ~CCMR_MDS /* Switch to MCU PLL */
/* PBC CPLD on CS4 */
mov r1, #CS4_BASE
ldrh r1, [r1, #0x2]
/* Is 27MHz switch set? */
ands r1, r1, #0x10
/* 532-133-66.5 */
ldr r0, =CCM_BASE
ldr r1, =0xFF871D58
/* PDR0 */
str r1, [r0, #0x4]
ldreq r1, MPCTL_PARAM_532
ldrne r1, MPCTL_PARAM_532_27
/* MPCTL */
str r1, [r0, #0x10]
/* Set UPLL=240MHz, USB=60MHz */
ldr r1, =0x49FCFE7F
/* PDR1 */
str r1, [r0, #0x8]
ldreq r1, UPCTL_PARAM_240
ldrne r1, UPCTL_PARAM_240_27
/* UPCTL */
str r1, [r0, #0x14]
/* default CLKO to 1/8 of the ARM core */
mov r1, #0x000002C0
add r1, r1, #0x00000006
/* COSR */
str r1, [r0, #0x1c]
/* RedBoot sets 0x3f, 7, 7, 3, 5, 1, 3, 0 */
/* REG CCM_PDR0, PDR0_CSI_PODF(0x3f) | PDR0_CSI_PRDF(7) | PDR0_PER_PODF(7) | PDR0_HSP_PODF(2) | PDR0_NFC_PODF(6) | PDR0_IPG_PODF(1) | PDR0_MAX_PODF(2) | PDR0_MCU_PODF(0)*/
/* Redboot: 0, 51, 10, 12 / 0, 14, 9, 13 */
/* REG CCM_MPCTL, PLL_PD(0) | PLL_MFD(0x33) | PLL_MFI(7) | PLL_MFN(0x23)*/
/* Default: 1, 4, 12, 1 */
REG CCM_SPCTL, PLL_PD(1) | PLL_MFD(4) | PLL_MFI(12) | PLL_MFN(1)
/* B8xxxxxx - NAND, 8xxxxxxx - CSD0 RAM */
REG 0xB8001010, 0x00000004
REG 0xB8001004, 0x006ac73a
REG 0xB8001000, 0x92100000
REG 0x80000f00, 0x12344321
REG 0xB8001000, 0xa2100000
REG 0x80000000, 0x12344321
REG 0x80000000, 0x12344321
REG 0xB8001000, 0xb2100000
REG8 0x80000033, 0xda
REG8 0x81000000, 0xff
REG 0xB8001000, 0x82226080
REG 0x80000000, 0xDEADBEEF
REG 0xB8001010, 0x0000000c
mov pc, lr
MPCTL_PARAM_532:
.word (((1-1) << 26) + ((52-1) << 16) + (10 << 10) + (12 << 0))
MPCTL_PARAM_532_27:
.word (((1-1) << 26) + ((15-1) << 16) + (9 << 10) + (13 << 0))
UPCTL_PARAM_240:
.word (((2-1) << 26) + ((13-1) << 16) + (9 << 10) + (3 << 0))
UPCTL_PARAM_240_27:
.word (((2-1) << 26) + ((9 -1) << 16) + (8 << 10) + (8 << 0))