| /******************************************************************************* |
| Copyright (C) Marvell International Ltd. and its affiliates |
| |
| ******************************************************************************** |
| Marvell GPL License Option |
| |
| If you received this File from Marvell, you may opt to use, redistribute and/or |
| modify this File in accordance with the terms and conditions of the General |
| Public License Version 2, June 1991 (the "GPL License"), a copy of which is |
| available along with the File in the license.txt file or by writing to the Free |
| Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 or |
| on the worldwide web at http://www.gnu.org/licenses/gpl.txt. |
| |
| THE FILE IS DISTRIBUTED AS-IS, WITHOUT WARRANTY OF ANY KIND, AND THE IMPLIED |
| WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY |
| DISCLAIMED. The GPL License provides additional details about this warranty |
| disclaimer. |
| |
| *******************************************************************************/ |
| /******************************************************************************* |
| * mvSysHwCfg.h - Marvell system HW configuration file |
| * |
| * DESCRIPTION: |
| * None. |
| * |
| * DEPENDENCIES: |
| * None. |
| * |
| *******************************************************************************/ |
| |
| #ifndef __INCmvSysHwConfigh |
| #define __INCmvSysHwConfigh |
| |
| #include <config.h> |
| |
| /****************************************/ |
| /* Soc supporetd Units definitions */ |
| /****************************************/ |
| #undef MV_MEM_OVER_PEX_WA |
| |
| #define MV_INCLUDE_PEX |
| #define MV_INCLUDE_GIG_ETH |
| //#define MV_INCLUDE_CESA |
| //#define MV_INCLUDE_SWITCH |
| #define OLD_CESA_HAL |
| #define MV_INCLUDE_USB |
| #define MV_INCLUDE_TWSI |
| #define MV_INCLUDE_NAND |
| #define MV_INCLUDE_UART |
| #define MV_INCLUDE_SPI |
| #define MV_INCLUDE_TDM |
| #define MV_INCLUDE_XOR |
| #define MV_INCLUDE_SATA |
| //#define MV_INCLUDE_TS |
| //#define MV_INCLUDE_AUDIO |
| #define MV_INCLUDE_SDIO |
| #define MV_INCLUDE_RTC |
| #define MV_INCLUDE_INTEG_SATA |
| #define MV_INCLUDE_CLK_PWR_CNTRL |
| |
| /*********************************************/ |
| /* Board Specific defines : On-Board devices */ |
| /*********************************************/ |
| |
| /* DRAM ddim detection support */ |
| #define MV_INC_BOARD_DDIM |
| /* On-Board NAND Flash support */ |
| #define MV_INC_BOARD_NAND_FLASH |
| /* On-Board SPI Flash support */ |
| #define MV_INC_BOARD_SPI_FLASH |
| /* On-Board RTC */ |
| #define MV_INC_BOARD_RTC |
| |
| /* PEX-PCI\PCI-PCI Bridge*/ |
| #define PCI0_IF_PTP 0 /* no Bridge on pciIf0*/ |
| #define PCI1_IF_PTP 0 /* no Bridge on pciIf1*/ |
| |
| /************************************************/ |
| /* RD boards specifics */ |
| /************************************************/ |
| |
| #undef MV_INC_BOARD_DDIM |
| |
| #ifndef MV_BOOTROM |
| #define MV_STATIC_DRAM_ON_BOARD |
| #endif |
| |
| #if defined(RD_88F6281) |
| #define MV_INC_BOARD_QD_SWITCH |
| #endif |
| |
| #if defined(RD_88F6180) |
| #define MV_INC_BOARD_QD_SWITCH |
| #endif |
| /* |
| * System memory mapping |
| */ |
| |
| /* SDRAM: actual mapping is auto detected */ |
| #define SDRAM_CS0_BASE 0x00000000 |
| #define SDRAM_CS0_SIZE _256M |
| |
| #define SDRAM_CS1_BASE 0x10000000 |
| #define SDRAM_CS1_SIZE _256M |
| |
| #define SDRAM_CS2_BASE 0x20000000 |
| #define SDRAM_CS2_SIZE _256M |
| |
| #define SDRAM_CS3_BASE 0x30000000 |
| #define SDRAM_CS3_SIZE _256M |
| |
| |
| /* |
| * PEX Address Decoding |
| */ |
| #define PEX0_MEM_BASE 0xB0000000 |
| #define PEX0_MEM_SIZE _32M |
| #define PEX1_MEM_BASE 0xB2000000 |
| #define PEX1_MEM_SIZE _32M |
| |
| #define PEX0_IO_BASE 0xC1100000 |
| #define PEX0_IO_SIZE _1M |
| #define PEX1_IO_BASE 0xC1200000 |
| #define PEX1_IO_SIZE _1M |
| |
| /* Device: CS0 - NOR or NAND, CS1 - SPI, CS2 - Boot ROM, CS3 - Boot device */ |
| /* NOR and NAND are configure to CS0 but it is posible to load |
| NOR as BOOT_CS and NAND ad CS0 otherwise only NOR or NAND it posible */ |
| /* Internal registers: size is defined in Controllerenvironment */ |
| |
| //#define INTER_REGS_BASE 0xF1000000 |
| #define INTER_REGS_BASE 0xD0000000 |
| #define ARMADAXP_SB_REGS_PHYS_BASE INTER_REGS_BASE |
| |
| #define NFLASH_CS_BASE 0xfd000000 /* not relevant for the new controller */ |
| #define NFLASH_CS_SIZE _2M |
| |
| #define NOR_CS_BASE 0xfd000000 |
| #define NOR_CS_SIZE _16M |
| |
| #define SPI_CS_BASE 0xf4000000 /*0xf8000000*/ |
| #define SPI_CS_SIZE _16M |
| |
| #define PNC_BM_PHYS_BASE 0xf2100000 /*0xF5000000*/ |
| #define PNC_BM_SIZE _1M |
| |
| /* Important for MP - Do not disable/change this window */ |
| #define CRYPT_ENG_BASE 0xc8010000 |
| #define CRYPT_ENG_SIZE _64K |
| |
| #define DEVICE_SPI_BASE SPI_CS_BASE |
| |
| #ifdef MV_INCLUDE_NOR |
| #define DEVICE_CS0_BASE NOR_CS_BASE |
| #define DEVICE_CS0_SIZE NOR_CS_SIZE |
| #else |
| #define DEVICE_CS0_BASE NFLASH_CS_BASE |
| #define DEVICE_CS0_SIZE NFLASH_CS_SIZE |
| #endif |
| |
| #define DEVICE_CS1_BASE SPI_CS_BASE |
| #define DEVICE_CS1_SIZE _16M |
| |
| #define DEVICE_CS2_BASE 0xf2000000 /* 0xf4000000 */ |
| #define DEVICE_CS2_SIZE _1M |
| |
| #define DEVICE_CS3_BASE BOOTDEV_CS_BASE |
| #define DEVICE_CS3_SIZE BOOTDEV_CS_SIZE |
| |
| |
| #if !defined(MV_BOOTROM) && defined(MV_NAND_BOOT) |
| #define CONFIG_SYS_NAND_BASE BOOTDEV_CS_BASE |
| #else |
| #define CONFIG_SYS_NAND_BASE DEVICE_CS0_BASE |
| #endif |
| |
| #if defined (MV_INCLUDE_PEX) |
| #define PCI_IF0_MEM0_BASE PEX0_MEM_BASE |
| #define PCI_IF0_MEM0_SIZE PEX0_MEM_SIZE |
| #define PCI_IF0_IO_BASE PEX0_IO_BASE |
| #define PCI_IF0_IO_SIZE PEX0_IO_SIZE |
| #endif |
| |
| /* DRAM detection stuff */ |
| #define MV_DRAM_AUTO_SIZE |
| |
| #define PCI_ARBITER_CTRL /* Use/unuse the Marvell integrated PCI arbiter */ |
| #undef PCI_ARBITER_BOARD /* Use/unuse the PCI arbiter on board */ |
| |
| /* Check macro validity */ |
| #if defined(PCI_ARBITER_CTRL) && defined (PCI_ARBITER_BOARD) |
| #error "Please select either integrated PCI arbiter or board arbiter" |
| #endif |
| |
| /* Board clock detection */ |
| #define TCLK_AUTO_DETECT /* Use Tclk auto detection */ |
| #define SYSCLK_AUTO_DETECT /* Use SysClk auto detection */ |
| #define PCLCK_AUTO_DETECT /* Use PClk auto detection */ |
| #define L2CLK_AUTO_DETECT /* Use L2 Clk auto detection */ |
| |
| /************* Ethernet driver configuration ********************/ |
| |
| /*#define ETH_JUMBO_SUPPORT*/ |
| /* HW cache coherency configuration */ |
| #define DMA_RAM_COHER NO_COHERENCY |
| #define ETHER_DRAM_COHER MV_UNCACHED |
| #define INTEG_SRAM_COHER MV_UNCACHED /* Where integrated SRAM available */ |
| |
| #define ETH_DESCR_IN_SDRAM |
| #undef ETH_DESCR_IN_SRAM |
| |
| #if (ETHER_DRAM_COHER == MV_CACHE_COHER_HW_WB) |
| # define ETH_SDRAM_CONFIG_STR "MV_CACHE_COHER_HW_WB" |
| #elif (ETHER_DRAM_COHER == MV_CACHE_COHER_HW_WT) |
| # define ETH_SDRAM_CONFIG_STR "MV_CACHE_COHER_HW_WT" |
| #elif (ETHER_DRAM_COHER == MV_CACHE_COHER_SW) |
| # define ETH_SDRAM_CONFIG_STR "MV_CACHE_COHER_SW" |
| #elif (ETHER_DRAM_COHER == MV_UNCACHED) |
| # define ETH_SDRAM_CONFIG_STR "MV_UNCACHED" |
| #else |
| # error "Unexpected ETHER_DRAM_COHER value" |
| #endif /* ETHER_DRAM_COHER */ |
| |
| /*********** Idma default configuration ***********/ |
| #define UBOOT_CNTRL_DMA_DV (ICCLR_DST_BURST_LIM_8BYTE | \ |
| ICCLR_SRC_INC | \ |
| ICCLR_DST_INC | \ |
| ICCLR_SRC_BURST_LIM_8BYTE | \ |
| ICCLR_NON_CHAIN_MODE | \ |
| ICCLR_BLOCK_MODE ) |
| |
| /* CPU address decode table. Note that table entry number must match its */ |
| /* winNum enumerator. For example, table entry '4' must describe Deivce CS0 */ |
| /* winNum which is represent by DEVICE_CS0 enumerator (4). */ |
| #define MV_CPU_IF_ADDR_WIN_MAP_TBL { \ |
| /* base low base high size WinNum enable */ \ |
| {{SDRAM_CS0_BASE, 0, SDRAM_CS0_SIZE }, 0xFFFFFFFF, DIS}, /* SDRAM_CS0 */ \ |
| {{SDRAM_CS1_BASE, 0, SDRAM_CS1_SIZE }, 0xFFFFFFFF, DIS}, /* SDRAM_CS1 */ \ |
| {{SDRAM_CS2_BASE, 0, SDRAM_CS2_SIZE }, 0xFFFFFFFF, DIS}, /* SDRAM_CS2 */ \ |
| {{SDRAM_CS3_BASE, 0, SDRAM_CS3_SIZE }, 0xFFFFFFFF, DIS}, /* SDRAM_CS3 */ \ |
| {{TBL_UNUSED, 0, TBL_UNUSED }, 10, DIS}, /* DEVICE_CS0 */\ |
| {{TBL_UNUSED, 0, TBL_UNUSED }, TBL_UNUSED, DIS}, /* DEVICE_CS1 */\ |
| {{TBL_UNUSED, 0, TBL_UNUSED }, TBL_UNUSED, DIS}, /* DEVICE_CS2 */\ |
| {{TBL_UNUSED, 0, TBL_UNUSED }, TBL_UNUSED, DIS}, /* DEVICE_CS3 */\ |
| {{PEX0_MEM_BASE, 0, PEX0_MEM_SIZE }, 0, EN}, /* PEX0_MEM */ \ |
| {{PEX0_IO_BASE, 0, PEX0_IO_SIZE }, TBL_UNUSED, DIS}, /* PEX0_IO */ \ |
| {{PEX1_MEM_BASE, 0, PEX1_MEM_SIZE }, 1, EN}, /* PEX1_MEM */ \ |
| {{PEX1_IO_BASE, 0, PEX1_IO_SIZE }, TBL_UNUSED, DIS}, /* PEX1_IO */ \ |
| {{INTER_REGS_BASE, 0, INTER_REGS_SIZE }, MV_AHB_TO_MBUS_INTREG_WIN, EN}, /* INTER_REGS */\ |
| {{TBL_UNUSED, 0, TBL_UNUSED }, TBL_UNUSED, DIS}, /* DMA_UART */\ |
| {{SPI_CS_BASE, 0, SPI_CS_SIZE }, 8, EN}, /* SPI_CS0 */ \ |
| {{TBL_UNUSED, 0, TBL_UNUSED }, TBL_UNUSED, DIS}, /* SPI_CS1 */ \ |
| {{TBL_UNUSED, 0, TBL_UNUSED }, TBL_UNUSED, DIS}, /* SPI_CS2 */ \ |
| {{TBL_UNUSED, 0, TBL_UNUSED }, TBL_UNUSED, DIS}, /* SPI_CS3 */ \ |
| {{TBL_UNUSED, 0, TBL_UNUSED }, TBL_UNUSED, DIS}, /* SPI_CS4 */ \ |
| {{TBL_UNUSED, 0, TBL_UNUSED }, TBL_UNUSED, DIS}, /* SPI_CS5 */ \ |
| {{TBL_UNUSED, 0, TBL_UNUSED }, TBL_UNUSED, DIS}, /* SPI_CS6 */ \ |
| {{TBL_UNUSED, 0, TBL_UNUSED }, TBL_UNUSED, DIS}, /* SPI_CS7 */ \ |
| {{0xf8000000, 0, _1M }, 13, EN}, /* BOOT_ROM_CS */\ |
| {{NOR_CS_BASE, 0, NOR_CS_SIZE }, 9, EN}, /* DEV_BOOCS */ \ |
| {{TBL_UNUSED, 0, TBL_UNUSED }, TBL_UNUSED, DIS}, /* PMU_SCRATCHPAD */ \ |
| {{CRYPT_ENG_BASE, 0, CRYPT_ENG_SIZE }, 10, EN}, /* CRYPT_ENG */ \ |
| {{TBL_TERM, TBL_TERM, TBL_TERM }, TBL_TERM, TBL_TERM} \ |
| }; |
| //{{PNC_BM_PHYS_BASE, 0, PNC_BM_SIZE }, TBL_UNUSED, DIS}, /* PNC_BM */ |
| //{{BOOTDEV_CS_BASE, 0, BOOTDEV_CS_SIZE }, 0x4, DIS}, /* DEV_BOOCS */ |
| |
| #define MV_CACHEABLE(address) ((address) | 0x80000000) |
| |
| /* includes */ |
| #define _1K 0x00000400 |
| #define _4K 0x00001000 |
| #define _8K 0x00002000 |
| #define _16K 0x00004000 |
| #define _32K 0x00008000 |
| #define _64K 0x00010000 |
| #define _128K 0x00020000 |
| #define _256K 0x00040000 |
| #define _512K 0x00080000 |
| |
| #define _1M 0x00100000 |
| #define _2M 0x00200000 |
| #define _4M 0x00400000 |
| #define _8M 0x00800000 |
| #define _16M 0x01000000 |
| #define _32M 0x02000000 |
| #define _64M 0x04000000 |
| #define _128M 0x08000000 |
| #define _256M 0x10000000 |
| #define _512M 0x20000000 |
| |
| #define _1G 0x40000000 |
| #define _2G 0x80000000 |
| |
| |
| #if defined(MV_BOOTSIZE_256K) |
| |
| #define BOOTDEV_CS_SIZE _256K |
| |
| #elif defined(MV_BOOTSIZE_512K) |
| |
| #define BOOTDEV_CS_SIZE _512K |
| |
| #elif defined(MV_BOOTSIZE_4M) |
| |
| #define BOOTDEV_CS_SIZE _4M |
| |
| #elif defined(MV_BOOTSIZE_8M) |
| |
| #define BOOTDEV_CS_SIZE _8M |
| |
| #elif defined(MV_BOOTSIZE_16M) |
| |
| #define BOOTDEV_CS_SIZE _16M |
| |
| #elif defined(MV_BOOTSIZE_32M) |
| |
| #define BOOTDEV_CS_SIZE _32M |
| |
| #elif defined(MV_BOOTSIZE_64M) |
| |
| #define BOOTDEV_CS_SIZE _64M |
| |
| #elif defined(MV_NAND_BOOT) |
| |
| #define BOOTDEV_CS_SIZE _512K |
| |
| #else |
| |
| #define Error MV_BOOTSIZE undefined |
| |
| #endif |
| |
| #define BOOTDEV_CS_BASE ((0xFFFFFFFF - BOOTDEV_CS_SIZE) + 1) |
| |
| /* We use the following registers to store DRAM interface pre configuration */ |
| /* auto-detection results */ |
| /* IMPORTANT: We are using mask register for that purpose. Before writing */ |
| /* to units mask register, make sure main maks register is set to disable */ |
| /* all interrupts. */ |
| #define DRAM_BUF_REG0 0x30810 /* sdram bank 0 size */ |
| #define DRAM_BUF_REG1 0x30820 /* sdram config */ |
| #define DRAM_BUF_REG2 0x30830 /* sdram mode */ |
| #define DRAM_BUF_REG3 0x60bb0 /* dunit control low */ |
| #define DRAM_BUF_REG4 0x60a90 /* sdram address control */ |
| #define DRAM_BUF_REG5 0x60a94 /* sdram timing control low */ |
| #define DRAM_BUF_REG6 0x60a98 /* sdram timing control high */ |
| #define DRAM_BUF_REG7 0x60a9c /* sdram ODT control low */ |
| #define DRAM_BUF_REG8 0x60b90 /* sdram ODT control high */ |
| #define DRAM_BUF_REG9 0x60b94 /* sdram Dunit ODT control */ |
| #define DRAM_BUF_REG10 0x60b98 /* sdram Extended Mode */ |
| #define DRAM_BUF_REG11 0x60b9c /* sdram Ddr2 Time Low Reg */ |
| #define DRAM_BUF_REG12 0x60bb4 /* sdram Ddr2 Time High Reg */ |
| #define DRAM_BUF_REG13 0x60ab0 /* dunit Ctrl High */ |
| #define DRAM_BUF_REG14 0x60ab4 /* sdram second DIMM exist */ |
| |
| /* Following the pre-configuration registers default values restored after */ |
| /* auto-detection is done */ |
| #define DRAM_BUF_REG_DV 0 |
| |
| #define ETH_DEF_TXQ 0 |
| #define ETH_DEF_RXQ 0 |
| #define MV_ETH_TX_Q_NUM 1 |
| #define MV_ETH_RX_Q_NUM 1 |
| #define ETH_NUM_OF_RX_DESCR 64 |
| #define ETH_NUM_OF_TX_DESCR ETH_NUM_OF_RX_DESCR*2 |
| |
| #define MV_CESA_MAX_BUF_SIZE 1600 |
| |
| #endif /* __INCmvSysHwConfigh */ |
