| /* |
| * dm355evm_msp.h - support MSP430 microcontroller on DM355EVM board |
| */ |
| #ifndef __LINUX_I2C_DM355EVM_MSP |
| #define __LINUX_I2C_DM355EVM_MSP |
| |
| /* |
| * Written against Spectrum's writeup for the A4 firmware revision, |
| * and tweaked to match source and rev D2 schematics by removing CPLD |
| * and NOR flash hooks (which were last appropriate in rev B boards). |
| * |
| * Note that the firmware supports a flavor of write posting ... to be |
| * sure a write completes, issue another read or write. |
| */ |
| |
| /* utilities to access "registers" emulated by msp430 firmware */ |
| extern int dm355evm_msp_write(u8 value, u8 reg); |
| extern int dm355evm_msp_read(u8 reg); |
| |
| |
| /* command/control registers */ |
| #define DM355EVM_MSP_COMMAND 0x00 |
| # define MSP_COMMAND_NULL 0 |
| # define MSP_COMMAND_RESET_COLD 1 |
| # define MSP_COMMAND_RESET_WARM 2 |
| # define MSP_COMMAND_RESET_WARM_I 3 |
| # define MSP_COMMAND_POWEROFF 4 |
| # define MSP_COMMAND_IR_REINIT 5 |
| #define DM355EVM_MSP_STATUS 0x01 |
| # define MSP_STATUS_BAD_OFFSET BIT(0) |
| # define MSP_STATUS_BAD_COMMAND BIT(1) |
| # define MSP_STATUS_POWER_ERROR BIT(2) |
| # define MSP_STATUS_RXBUF_OVERRUN BIT(3) |
| #define DM355EVM_MSP_RESET 0x02 /* 0 bits == in reset */ |
| # define MSP_RESET_DC5 BIT(0) |
| # define MSP_RESET_TVP5154 BIT(2) |
| # define MSP_RESET_IMAGER BIT(3) |
| # define MSP_RESET_ETHERNET BIT(4) |
| # define MSP_RESET_SYS BIT(5) |
| # define MSP_RESET_AIC33 BIT(7) |
| |
| /* GPIO registers ... bit patterns mostly match the source MSP ports */ |
| #define DM355EVM_MSP_LED 0x03 /* active low (MSP P4) */ |
| #define DM355EVM_MSP_SWITCH1 0x04 /* (MSP P5, masked) */ |
| # define MSP_SWITCH1_SW6_1 BIT(0) |
| # define MSP_SWITCH1_SW6_2 BIT(1) |
| # define MSP_SWITCH1_SW6_3 BIT(2) |
| # define MSP_SWITCH1_SW6_4 BIT(3) |
| # define MSP_SWITCH1_J1 BIT(4) /* NTSC/PAL */ |
| # define MSP_SWITCH1_MSP_INT BIT(5) /* active low */ |
| #define DM355EVM_MSP_SWITCH2 0x05 /* (MSP P6, masked) */ |
| # define MSP_SWITCH2_SW10 BIT(3) |
| # define MSP_SWITCH2_SW11 BIT(4) |
| # define MSP_SWITCH2_SW12 BIT(5) |
| # define MSP_SWITCH2_SW13 BIT(6) |
| # define MSP_SWITCH2_SW14 BIT(7) |
| #define DM355EVM_MSP_SDMMC 0x06 /* (MSP P2, masked) */ |
| # define MSP_SDMMC_0_WP BIT(1) |
| # define MSP_SDMMC_0_CD BIT(2) /* active low */ |
| # define MSP_SDMMC_1_WP BIT(3) |
| # define MSP_SDMMC_1_CD BIT(4) /* active low */ |
| #define DM355EVM_MSP_FIRMREV 0x07 /* not a GPIO (out of order) */ |
| #define DM355EVM_MSP_VIDEO_IN 0x08 /* (MSP P3, masked) */ |
| # define MSP_VIDEO_IMAGER BIT(7) /* low == tvp5146 */ |
| |
| /* power supply registers are currently omitted */ |
| |
| /* RTC registers */ |
| #define DM355EVM_MSP_RTC_0 0x12 /* LSB */ |
| #define DM355EVM_MSP_RTC_1 0x13 |
| #define DM355EVM_MSP_RTC_2 0x14 |
| #define DM355EVM_MSP_RTC_3 0x15 /* MSB */ |
| |
| /* input event queue registers; code == ((HIGH << 8) | LOW) */ |
| #define DM355EVM_MSP_INPUT_COUNT 0x16 /* decrement by reading LOW */ |
| #define DM355EVM_MSP_INPUT_HIGH 0x17 |
| #define DM355EVM_MSP_INPUT_LOW 0x18 |
| |
| #endif /* __LINUX_I2C_DM355EVM_MSP */ |
