| [state: 03-05-2010] |
| |
| BATMAN-ADV |
| ---------- |
| |
| Batman advanced is a new approach to wireless networking which |
| does no longer operate on the IP basis. Unlike the batman daemon, |
| which exchanges information using UDP packets and sets routing |
| tables, batman-advanced operates on ISO/OSI Layer 2 only and uses |
| and routes (or better: bridges) Ethernet Frames. It emulates a |
| virtual network switch of all nodes participating. Therefore all |
| nodes appear to be link local, thus all higher operating proto- |
| cols won't be affected by any changes within the network. You can |
| run almost any protocol above batman advanced, prominent examples |
| are: IPv4, IPv6, DHCP, IPX. |
| |
| Batman advanced was implemented as a Linux kernel driver to re- |
| duce the overhead to a minimum. It does not depend on any (other) |
| network driver, and can be used on wifi as well as ethernet lan, |
| vpn, etc ... (anything with ethernet-style layer 2). |
| |
| CONFIGURATION |
| ------------- |
| |
| Load the batman-adv module into your kernel: |
| |
| # insmod batman-adv.ko |
| |
| The module is now waiting for activation. You must add some in- |
| terfaces on which batman can operate. After loading the module |
| batman advanced will scan your systems interfaces to search for |
| compatible interfaces. Once found, it will create subfolders in |
| the /sys directories of each supported interface, e.g. |
| |
| # ls /sys/class/net/eth0/batman_adv/ |
| # iface_status mesh_iface |
| |
| If an interface does not have the "batman_adv" subfolder it prob- |
| ably is not supported. Not supported interfaces are: loopback, |
| non-ethernet and batman's own interfaces. |
| |
| Note: After the module was loaded it will continuously watch for |
| new interfaces to verify the compatibility. There is no need to |
| reload the module if you plug your USB wifi adapter into your ma- |
| chine after batman advanced was initially loaded. |
| |
| To activate a given interface simply write "bat0" into its |
| "mesh_iface" file inside the batman_adv subfolder: |
| |
| # echo bat0 > /sys/class/net/eth0/batman_adv/mesh_iface |
| |
| Repeat this step for all interfaces you wish to add. Now batman |
| starts using/broadcasting on this/these interface(s). |
| |
| By reading the "iface_status" file you can check its status: |
| |
| # cat /sys/class/net/eth0/batman_adv/iface_status |
| # active |
| |
| To deactivate an interface you have to write "none" into its |
| "mesh_iface" file: |
| |
| # echo none > /sys/class/net/eth0/batman_adv/mesh_iface |
| |
| |
| All mesh wide settings can be found in batman's own interface |
| folder: |
| |
| # ls /sys/class/net/bat0/mesh/ |
| # aggregate_ogm originators transtable_global vis_mode |
| # orig_interval transtable_local vis_data |
| |
| |
| Some of the files contain all sort of status information regard- |
| ing the mesh network. For example, you can view the table of |
| originators (mesh participants) with: |
| |
| # cat /sys/class/net/bat0/mesh/originators |
| |
| Other files allow to change batman's behaviour to better fit your |
| requirements. For instance, you can check the current originator |
| interval (value in milliseconds which determines how often batman |
| sends its broadcast packets): |
| |
| # cat /sys/class/net/bat0/mesh/orig_interval |
| # status: 1000 |
| |
| and also change its value: |
| |
| # echo 3000 > /sys/class/net/bat0/mesh/orig_interval |
| |
| In very mobile scenarios, you might want to adjust the originator |
| interval to a lower value. This will make the mesh more respon- |
| sive to topology changes, but will also increase the overhead. |
| |
| |
| USAGE |
| ----- |
| |
| To make use of your newly created mesh, batman advanced provides |
| a new interface "bat0" which you should use from this point on. |
| All interfaces added to batman advanced are not relevant any |
| longer because batman handles them for you. Basically, one "hands |
| over" the data by using the batman interface and batman will make |
| sure it reaches its destination. |
| |
| The "bat0" interface can be used like any other regular inter- |
| face. It needs an IP address which can be either statically con- |
| figured or dynamically (by using DHCP or similar services): |
| |
| # NodeA: ifconfig bat0 192.168.0.1 |
| # NodeB: ifconfig bat0 192.168.0.2 |
| # NodeB: ping 192.168.0.1 |
| |
| Note: In order to avoid problems remove all IP addresses previ- |
| ously assigned to interfaces now used by batman advanced, e.g. |
| |
| # ifconfig eth0 0.0.0.0 |
| |
| |
| VISUALIZATION |
| ------------- |
| |
| If you want topology visualization, at least one mesh node must |
| be configured as VIS-server: |
| |
| # echo "server" > /sys/class/net/bat0/mesh/vis_mode |
| |
| Each node is either configured as "server" or as "client" (de- |
| fault: "client"). Clients send their topology data to the server |
| next to them, and server synchronize with other servers. If there |
| is no server configured (default) within the mesh, no topology |
| information will be transmitted. With these "synchronizing |
| servers", there can be 1 or more vis servers sharing the same (or |
| at least very similar) data. |
| |
| When configured as server, you can get a topology snapshot of |
| your mesh: |
| |
| # cat /sys/class/net/bat0/mesh/vis_data |
| |
| This raw output is intended to be easily parsable and convertable |
| with other tools. Have a look at the batctl README if you want a |
| vis output in dot or json format for instance and how those out- |
| puts could then be visualised in an image. |
| |
| The raw format consists of comma separated values per entry where |
| each entry is giving information about a certain source inter- |
| face. Each entry can/has to have the following values: |
| -> "mac" - mac address of an originator's source interface |
| (each line begins with it) |
| -> "TQ mac value" - src mac's link quality towards mac address |
| of a neighbor originator's interface which |
| is being used for routing |
| -> "HNA mac" - HNA announced by source mac |
| -> "PRIMARY" - this is a primary interface |
| -> "SEC mac" - secondary mac address of source |
| (requires preceding PRIMARY) |
| |
| The TQ value has a range from 4 to 255 with 255 being the best. |
| The HNA entries are showing which hosts are connected to the mesh |
| via bat0 or being bridged into the mesh network. The PRIMARY/SEC |
| values are only applied on primary interfaces |
| |
| |
| LOGGING/DEBUGGING |
| ----------------- |
| |
| All error messages, warnings and information messages are sent to |
| the kernel log. Depending on your operating system distribution |
| this can be read in one of a number of ways. Try using the com- |
| mands: dmesg, logread, or looking in the files /var/log/kern.log |
| or /var/log/syslog. All batman-adv messages are prefixed with |
| "batman-adv:" So to see just these messages try |
| |
| # dmesg | grep batman-adv |
| |
| When investigating problems with your mesh network it is some- |
| times necessary to see more detail debug messages. This must be |
| enabled when compiling the batman-adv module. When building bat- |
| man-adv as part of kernel, use "make menuconfig" and enable the |
| option "B.A.T.M.A.N. debugging". |
| |
| The additional debug output is by default disabled. It can be en- |
| abled either at kernel modules load time or during run time. To |
| enable debug output at module load time, add the module parameter |
| debug=<value>. <value> can take one of four values. |
| |
| 0 - All debug output disabled |
| 1 - Enable messages related to routing / flooding / broadcasting |
| 2 - Enable route or hna added / changed / deleted |
| 3 - Enable all messages |
| |
| e.g. |
| |
| # modprobe batman-adv debug=2 |
| |
| will load the module and enable debug messages for when routes or |
| HNAs change. |
| |
| The debug output can also be changed at runtime using the file |
| /sys/module/batman-adv/parameters/debug. e.g. |
| |
| # echo 2 > /sys/module/batman-adv/parameters/debug |
| |
| enables debug messages for when routes or HNAs |
| |
| The debug output is sent to the kernel logs. So try dmesg, lo- |
| gread, etc to see the debug messages. |
| |
| |
| BATCTL |
| ------ |
| |
| As batman advanced operates on layer 2 all hosts participating in |
| the virtual switch are completely transparent for all protocols |
| above layer 2. Therefore the common diagnosis tools do not work |
| as expected. To overcome these problems batctl was created. At |
| the moment the batctl contains ping, traceroute, tcpdump and |
| interfaces to the kernel module settings. |
| |
| For more information, please see the manpage (man batctl). |
| |
| batctl is available on http://www.open-mesh.org/ |
| |
| |
| CONTACT |
| ------- |
| |
| Please send us comments, experiences, questions, anything :) |
| |
| IRC: #batman on irc.freenode.org |
| Mailing-list: b.a.t.m.a.n@open-mesh.net (optional subscription |
| at https://lists.open-mesh.org/mm/listinfo/b.a.t.m.a.n) |
| |
| You can also contact the Authors: |
| |
| Marek Lindner <lindner_marek@yahoo.de> |
| Simon Wunderlich <siwu@hrz.tu-chemnitz.de> |
| |