/*
 * Copyright (C) 2015 Phytec Messtechnik GmbH
 * Author: Teresa Remmet <t.remmet@phytec.de>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

/ {
	model = "Phytec AM335x phyBOARD-WEGA";
	compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx";

	regulators {
		compatible = "simple-bus";

		vcc3v3: fixedregulator@1 {
			compatible = "regulator-fixed";
			regulator-name = "vcc3v3";
			regulator-min-microvolt = <3300000>;
			regulator-max-microvolt = <3300000>;
			regulator-boot-on;
		};
	};
};

/* CAN Busses */
&am33xx_pinmux {
	dcan1_pins: pinmux_dcan1 {
		pinctrl-single,pins = <
			AM33XX_IOPAD(0x968, PIN_OUTPUT_PULLUP | MUX_MODE2) /* uart0_ctsn.d_can1_tx */
			AM33XX_IOPAD(0x96c, PIN_INPUT_PULLUP | MUX_MODE2) /* uart0_rtsn.d_can1_rx */
		>;
	};
};

&dcan1 {
	pinctrl-names = "default";
	pinctrl-0 = <&dcan1_pins>;
	status = "okay";
};

/* Ethernet */
&am33xx_pinmux {
	ethernet1_pins: pinmux_ethernet1 {
		pinctrl-single,pins = <
			AM33XX_IOPAD(0x840, PIN_OUTPUT | MUX_MODE1)		/* gpmc_a0.mii2_txen */
			AM33XX_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_a1.mii2_rxdv */
			AM33XX_IOPAD(0x848, PIN_OUTPUT | MUX_MODE1)		/* gpmc_a2.mii2_txd3 */
			AM33XX_IOPAD(0x84c, PIN_OUTPUT | MUX_MODE1)		/* gpmc_a3.mii2_txd2 */
			AM33XX_IOPAD(0x850, PIN_OUTPUT | MUX_MODE1)		/* gpmc_a4.mii2_txd1 */
			AM33XX_IOPAD(0x854, PIN_OUTPUT | MUX_MODE1)		/* gpmc_a5.mii2_txd0 */
			AM33XX_IOPAD(0x858, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_a6.mii2_txclk */
			AM33XX_IOPAD(0x85c, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_a7.mii2_rxclk */
			AM33XX_IOPAD(0x860, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_a8.mii2_rxd3 */
			AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_a9.mii2_rxd2 */
			AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_a10.mii2_rxd1 */
			AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_a11.mii2_rxd0 */
			AM33XX_IOPAD(0x874, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_wpn.mii2_rxerr */
			AM33XX_IOPAD(0x878, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_ben1.mii2_col */
		>;
	};
};

&cpsw_emac1 {
	phy_id = <&davinci_mdio>, <1>;
	phy-mode = "mii";
	dual_emac_res_vlan = <2>;
};

&mac {
	slaves = <2>;
	pinctrl-names = "default";
	pinctrl-0 = <&ethernet0_pins &ethernet1_pins>;
	dual_emac = <1>;
};

/* MMC */
&am33xx_pinmux {
	mmc1_pins: pinmux_mmc1 {
		pinctrl-single,pins = <
			AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat3.mmc0_dat3 */
			AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat2.mmc0_dat2 */
			AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat1.mmc0_dat1 */
			AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat0.mmc0_dat0 */
			AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_clk.mmc0_clk */
			AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_cmd.mmc0_cmd */
			AM33XX_IOPAD(0x960, PIN_INPUT_PULLUP | MUX_MODE7)	/* spi0_cs1.mmc0_sdcd */
		>;
	};
};

&mmc1 {
	vmmc-supply = <&vcc3v3>;
	bus-width = <4>;
	pinctrl-names = "default";
	pinctrl-0 = <&mmc1_pins>;
	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
	status = "okay";
};

/* UARTs */
&am33xx_pinmux {
	uart0_pins: pinmux_uart0 {
		pinctrl-single,pins = <
			AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0)    /* uart0_rxd.uart0_rxd */
			AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
		>;
	};

	uart1_pins: pinmux_uart1_pins {
		pinctrl-single,pins = <
			AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart1_rxd.uart1_rxd */
			AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_txd.uart1_txd */
			AM33XX_IOPAD(0x978, PIN_INPUT | MUX_MODE0)		/* uart1_ctsn.uart1_ctsn */
			AM33XX_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_rtsn.uart1_rtsn */
		>;
	};
};

&uart0 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart0_pins>;
	status = "okay";
};

&uart1 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart1_pins>;
	status = "okay";
};

/* USB */
&cppi41dma {
	status = "okay";
};

&usb_ctrl_mod {
	status = "okay";
};

&usb {
	status = "okay";
};

&usb0 {
	dr_mode = "peripheral";
	status = "okay";
};

&usb0_phy {
	status = "okay";
};

&usb1 {
	dr_mode = "host";
	status = "okay";
};

&usb1_phy {
	status = "okay";
};