| /* |
| This is part of rtl8187 OpenSource driver. |
| Copyright (C) Andrea Merello 2004-2005 <andrea.merello@gmail.com> |
| Released under the terms of GPL (General Public Licence) |
| |
| Parts of this driver are based on the GPL part of the |
| official Realtek driver. |
| Parts of this driver are based on the rtl8180 driver skeleton |
| from Patric Schenke & Andres Salomon. |
| Parts of this driver are based on the Intel Pro Wireless |
| 2100 GPL driver. |
| |
| We want to thank the Authors of those projects |
| and the Ndiswrapper project Authors. |
| */ |
| |
| /* Mariusz Matuszek added full registers definition with Realtek's name */ |
| |
| /* this file contains register definitions for the rtl8187 MAC controller */ |
| #ifndef R8192_HW |
| #define R8192_HW |
| |
| typedef enum _VERSION_819xU{ |
| VERSION_819xU_A, // A-cut |
| VERSION_819xU_B, // B-cut |
| VERSION_819xU_C,// C-cut |
| } VERSION_819xU, *PVERSION_819xU; |
| //added for different RF type |
| typedef enum _RT_RF_TYPE_DEF |
| { |
| RF_1T2R = 0, |
| RF_2T4R, |
| |
| RF_819X_MAX_TYPE |
| }RT_RF_TYPE_DEF; |
| |
| |
| typedef enum _BaseBand_Config_Type{ |
| BaseBand_Config_PHY_REG = 0, //Radio Path A |
| BaseBand_Config_AGC_TAB = 1, //Radio Path B |
| }BaseBand_Config_Type, *PBaseBand_Config_Type; |
| #define RTL8187_REQT_READ 0xc0 |
| #define RTL8187_REQT_WRITE 0x40 |
| #define RTL8187_REQ_GET_REGS 0x05 |
| #define RTL8187_REQ_SET_REGS 0x05 |
| |
| #define MAX_TX_URB 5 |
| #define MAX_RX_URB 16 |
| |
| #define R8180_MAX_RETRY 255 |
| //#define MAX_RX_NORMAL_URB 3 |
| //#define MAX_RX_COMMAND_URB 2 |
| #define RX_URB_SIZE 9100 |
| |
| #define BB_ANTATTEN_CHAN14 0x0c |
| #define BB_ANTENNA_B 0x40 |
| |
| #define BB_HOST_BANG BIT(30) |
| #define BB_HOST_BANG_EN BIT(2) |
| #define BB_HOST_BANG_CLK BIT(1) |
| #define BB_HOST_BANG_RW BIT(3) |
| #define BB_HOST_BANG_DATA 1 |
| |
| //#if (RTL819X_FPGA_VER & RTL819X_FPGA_VIVI_070920) |
| #define AFR 0x010 |
| #define AFR_CardBEn BIT(0) |
| #define AFR_CLKRUN_SEL BIT(1) |
| #define AFR_FuncRegEn BIT(2) |
| #define RTL8190_EEPROM_ID 0x8129 |
| #define EEPROM_VID 0x02 |
| #define EEPROM_PID 0x04 |
| #define EEPROM_NODE_ADDRESS_BYTE_0 0x0C |
| |
| #define EEPROM_TxPowerDiff 0x1F |
| #define EEPROM_ThermalMeter 0x20 |
| #define EEPROM_PwDiff 0x21 //0x21 |
| #define EEPROM_CrystalCap 0x22 //0x22 |
| |
| #define EEPROM_TxPwIndex_CCK 0x23 //0x23 |
| #define EEPROM_TxPwIndex_OFDM_24G 0x24 //0x24~0x26 |
| #define EEPROM_TxPwIndex_CCK_V1 0x29 //0x29~0x2B |
| #define EEPROM_TxPwIndex_OFDM_24G_V1 0x2C //0x2C~0x2E |
| #define EEPROM_TxPwIndex_Ver 0x27 //0x27 |
| |
| #define EEPROM_Default_TxPowerDiff 0x0 |
| #define EEPROM_Default_ThermalMeter 0x7 |
| #define EEPROM_Default_PwDiff 0x4 |
| #define EEPROM_Default_CrystalCap 0x5 |
| #define EEPROM_Default_TxPower 0x1010 |
| #define EEPROM_Customer_ID 0x7B //0x7B:CustomerID |
| #define EEPROM_ChannelPlan 0x16 //0x7C |
| #define EEPROM_IC_VER 0x7d //0x7D |
| #define EEPROM_CRC 0x7e //0x7E~0x7F |
| |
| #define EEPROM_CID_DEFAULT 0x0 |
| #define EEPROM_CID_CAMEO 0x1 |
| #define EEPROM_CID_RUNTOP 0x2 |
| #define EEPROM_CID_Senao 0x3 |
| #define EEPROM_CID_TOSHIBA 0x4 // Toshiba setting, Merge by Jacken, 2008/01/31 |
| #define EEPROM_CID_NetCore 0x5 |
| #define EEPROM_CID_Nettronix 0x6 |
| #define EEPROM_CID_Pronet 0x7 |
| #define EEPROM_CID_DLINK 0x8 |
| |
| #define AC_PARAM_TXOP_LIMIT_OFFSET 16 |
| #define AC_PARAM_ECW_MAX_OFFSET 12 |
| #define AC_PARAM_ECW_MIN_OFFSET 8 |
| #define AC_PARAM_AIFS_OFFSET 0 |
| |
| //#endif |
| enum _RTL8192Usb_HW { |
| |
| PCIF = 0x009, // PCI Function Register 0x0009h~0x000bh |
| #define BB_GLOBAL_RESET_BIT 0x1 |
| BB_GLOBAL_RESET = 0x020, // BasebandGlobal Reset Register |
| BSSIDR = 0x02E, // BSSID Register |
| CMDR = 0x037, // Command register |
| #define CR_RST 0x10 |
| #define CR_RE 0x08 |
| #define CR_TE 0x04 |
| #define CR_MulRW 0x01 |
| SIFS = 0x03E, // SIFS register |
| TCR = 0x040, // Transmit Configuration Register |
| |
| #define TCR_MXDMA_2048 7 |
| #define TCR_LRL_OFFSET 0 |
| #define TCR_SRL_OFFSET 8 |
| #define TCR_MXDMA_OFFSET 21 |
| #define TCR_SAT BIT(24) // Enable Rate depedent ack timeout timer |
| RCR = 0x044, // Receive Configuration Register |
| #define MAC_FILTER_MASK (BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(5) | \ |
| BIT(12) | BIT(18) | BIT(19) | BIT(20) | BIT(21) | \ |
| BIT(22) | BIT(23)) |
| #define RX_FIFO_THRESHOLD_MASK (BIT(13) | BIT(14) | BIT(15)) |
| #define RX_FIFO_THRESHOLD_SHIFT 13 |
| #define RX_FIFO_THRESHOLD_128 3 |
| #define RX_FIFO_THRESHOLD_256 4 |
| #define RX_FIFO_THRESHOLD_512 5 |
| #define RX_FIFO_THRESHOLD_1024 6 |
| #define RX_FIFO_THRESHOLD_NONE 7 |
| #define MAX_RX_DMA_MASK (BIT(8) | BIT(9) | BIT(10)) |
| #define RCR_MXDMA_OFFSET 8 |
| #define RCR_FIFO_OFFSET 13 |
| #define RCR_ONLYERLPKT BIT(31) // Early Receiving based on Packet Size. |
| #define RCR_ENCS2 BIT(30) // Enable Carrier Sense Detection Method 2 |
| #define RCR_ENCS1 BIT(29) // Enable Carrier Sense Detection Method 1 |
| #define RCR_ENMBID BIT(27) // Enable Multiple BssId. |
| #define RCR_ACKTXBW (BIT(24) | BIT(25)) // TXBW Setting of ACK frames |
| #define RCR_CBSSID BIT(23) // Accept BSSID match packet |
| #define RCR_APWRMGT BIT(22) // Accept power management packet |
| #define RCR_ADD3 BIT(21) // Accept address 3 match packet |
| #define RCR_AMF BIT(20) // Accept management type frame |
| #define RCR_ACF BIT(19) // Accept control type frame |
| #define RCR_ADF BIT(18) // Accept data type frame |
| #define RCR_RXFTH BIT(13) // Rx FIFO Threshold |
| #define RCR_AICV BIT(12) // Accept ICV error packet |
| #define RCR_ACRC32 BIT(5) // Accept CRC32 error packet |
| #define RCR_AB BIT(3) // Accept broadcast packet |
| #define RCR_AM BIT(2) // Accept multicast packet |
| #define RCR_APM BIT(1) // Accept physical match packet |
| #define RCR_AAP BIT(0) // Accept all unicast packet |
| SLOT_TIME = 0x049, // Slot Time Register |
| ACK_TIMEOUT = 0x04c, // Ack Timeout Register |
| PIFS_TIME = 0x04d, // PIFS time |
| USTIME = 0x04e, // Microsecond Tuning Register, Sets the microsecond time unit used by MAC clock. |
| EDCAPARA_BE = 0x050, // EDCA Parameter of AC BE |
| EDCAPARA_BK = 0x054, // EDCA Parameter of AC BK |
| EDCAPARA_VO = 0x058, // EDCA Parameter of AC VO |
| EDCAPARA_VI = 0x05C, // EDCA Parameter of AC VI |
| RFPC = 0x05F, // Rx FIFO Packet Count |
| CWRR = 0x060, // Contention Window Report Register |
| BCN_TCFG = 0x062, // Beacon Time Configuration |
| #define BCN_TCFG_CW_SHIFT 8 |
| #define BCN_TCFG_IFS 0 |
| BCN_INTERVAL = 0x070, // Beacon Interval (TU) |
| ATIMWND = 0x072, // ATIM Window Size (TU) |
| BCN_DRV_EARLY_INT = 0x074, // Driver Early Interrupt Time (TU). Time to send interrupt to notify to change beacon content before TBTT |
| BCN_DMATIME = 0x076, // Beacon DMA and ATIM interrupt time (US). Indicates the time before TBTT to perform beacon queue DMA |
| BCN_ERR_THRESH = 0x078, // Beacon Error Threshold |
| RWCAM = 0x0A0, //IN 8190 Data Sheet is called CAMcmd |
| WCAMI = 0x0A4, // Software write CAM input content |
| RCAMO = 0x0A8, // Software read/write CAM config |
| SECR = 0x0B0, //Security Configuration Register |
| #define SCR_TxUseDK BIT(0) //Force Tx Use Default Key |
| #define SCR_RxUseDK BIT(1) //Force Rx Use Default Key |
| #define SCR_TxEncEnable BIT(2) //Enable Tx Encryption |
| #define SCR_RxDecEnable BIT(3) //Enable Rx Decryption |
| #define SCR_SKByA2 BIT(4) //Search kEY BY A2 |
| #define SCR_NoSKMC BIT(5) //No Key Search for Multicast |
| #define SCR_UseDK 0x01 |
| #define SCR_TxSecEnable 0x02 |
| #define SCR_RxSecEnable 0x04 |
| TPPoll = 0x0fd, // Transmit priority polling register |
| PSR = 0x0ff, // Page Select Register |
| #define CPU_CCK_LOOPBACK 0x00030000 |
| #define CPU_GEN_SYSTEM_RESET 0x00000001 |
| #define CPU_GEN_FIRMWARE_RESET 0x00000008 |
| #define CPU_GEN_BOOT_RDY 0x00000010 |
| #define CPU_GEN_FIRM_RDY 0x00000020 |
| #define CPU_GEN_PUT_CODE_OK 0x00000080 |
| #define CPU_GEN_BB_RST 0x00000100 |
| #define CPU_GEN_PWR_STB_CPU 0x00000004 |
| #define CPU_GEN_NO_LOOPBACK_MSK 0xFFF8FFFF // Set bit18,17,16 to 0. Set bit19 |
| #define CPU_GEN_NO_LOOPBACK_SET 0x00080000 // Set BIT19 to 1 |
| |
| //---------------------------------------------------------------------------- |
| // 8190 CPU General Register (offset 0x100, 4 byte) |
| //---------------------------------------------------------------------------- |
| #define CPU_CCK_LOOPBACK 0x00030000 |
| #define CPU_GEN_SYSTEM_RESET 0x00000001 |
| #define CPU_GEN_FIRMWARE_RESET 0x00000008 |
| #define CPU_GEN_BOOT_RDY 0x00000010 |
| #define CPU_GEN_FIRM_RDY 0x00000020 |
| #define CPU_GEN_PUT_CODE_OK 0x00000080 |
| #define CPU_GEN_BB_RST 0x00000100 |
| #define CPU_GEN_PWR_STB_CPU 0x00000004 |
| #define CPU_GEN_NO_LOOPBACK_MSK 0xFFF8FFFF // Set bit18,17,16 to 0. Set bit19 |
| #define CPU_GEN_NO_LOOPBACK_SET 0x00080000 // Set BIT19 to 1 |
| CPU_GEN = 0x100, // CPU Reset Register |
| LED1Cfg = 0x154,// LED1 Configuration Register |
| LED0Cfg = 0x155,// LED0 Configuration Register |
| |
| AcmAvg = 0x170, // ACM Average Period Register |
| AcmHwCtrl = 0x171, // ACM Hardware Control Register |
| //---------------------------------------------------------------------------- |
| //// |
| //// 8190 AcmHwCtrl bits (offset 0x171, 1 byte) |
| ////---------------------------------------------------------------------------- |
| // |
| #define AcmHw_HwEn BIT(0) |
| #define AcmHw_BeqEn BIT(1) |
| #define AcmHw_ViqEn BIT(2) |
| #define AcmHw_VoqEn BIT(3) |
| #define AcmHw_BeqStatus BIT(4) |
| #define AcmHw_ViqStatus BIT(5) |
| #define AcmHw_VoqStatus BIT(6) |
| |
| AcmFwCtrl = 0x172, // ACM Firmware Control Register |
| AES_11N_FIX = 0x173, |
| VOAdmTime = 0x174, // VO Queue Admitted Time Register |
| VIAdmTime = 0x178, // VI Queue Admitted Time Register |
| BEAdmTime = 0x17C, // BE Queue Admitted Time Register |
| RQPN1 = 0x180, // Reserved Queue Page Number , Vo Vi, Be, Bk |
| RQPN2 = 0x184, // Reserved Queue Page Number, HCCA, Cmd, Mgnt, High |
| RQPN3 = 0x188, // Reserved Queue Page Number, Bcn, Public, |
| // QPRR = 0x1E0, // Queue Page Report per TID |
| QPNR = 0x1D0, //0x1F0, // Queue Packet Number report per TID |
| BQDA = 0x200, // Beacon Queue Descriptor Address |
| HQDA = 0x204, // High Priority Queue Descriptor Address |
| CQDA = 0x208, // Command Queue Descriptor Address |
| MQDA = 0x20C, // Management Queue Descriptor Address |
| HCCAQDA = 0x210, // HCCA Queue Descriptor Address |
| VOQDA = 0x214, // VO Queue Descriptor Address |
| VIQDA = 0x218, // VI Queue Descriptor Address |
| BEQDA = 0x21C, // BE Queue Descriptor Address |
| BKQDA = 0x220, // BK Queue Descriptor Address |
| RCQDA = 0x224, // Receive command Queue Descriptor Address |
| RDQDA = 0x228, // Receive Queue Descriptor Start Address |
| |
| MAR0 = 0x240, // Multicast filter. |
| MAR4 = 0x244, |
| |
| CCX_PERIOD = 0x250, // CCX Measurement Period Register, in unit of TU. |
| CLM_RESULT = 0x251, // CCA Busy fraction register. |
| NHM_PERIOD = 0x252, // NHM Measurement Period register, in unit of TU. |
| |
| NHM_THRESHOLD0 = 0x253, // Noise Histogram Meashorement0. |
| NHM_THRESHOLD1 = 0x254, // Noise Histogram Meashorement1. |
| NHM_THRESHOLD2 = 0x255, // Noise Histogram Meashorement2. |
| NHM_THRESHOLD3 = 0x256, // Noise Histogram Meashorement3. |
| NHM_THRESHOLD4 = 0x257, // Noise Histogram Meashorement4. |
| NHM_THRESHOLD5 = 0x258, // Noise Histogram Meashorement5. |
| NHM_THRESHOLD6 = 0x259, // Noise Histogram Meashorement6 |
| |
| MCTRL = 0x25A, // Measurement Control |
| |
| NHM_RPI_COUNTER0 = 0x264, // Noise Histogram RPI counter0, the fraction of signal strength < NHM_THRESHOLD0. |
| NHM_RPI_COUNTER1 = 0x265, // Noise Histogram RPI counter1, the fraction of signal strength in (NHM_THRESHOLD0, NHM_THRESHOLD1]. |
| NHM_RPI_COUNTER2 = 0x266, // Noise Histogram RPI counter2, the fraction of signal strength in (NHM_THRESHOLD1, NHM_THRESHOLD2]. |
| NHM_RPI_COUNTER3 = 0x267, // Noise Histogram RPI counter3, the fraction of signal strength in (NHM_THRESHOLD2, NHM_THRESHOLD3]. |
| NHM_RPI_COUNTER4 = 0x268, // Noise Histogram RPI counter4, the fraction of signal strength in (NHM_THRESHOLD3, NHM_THRESHOLD4]. |
| NHM_RPI_COUNTER5 = 0x269, // Noise Histogram RPI counter5, the fraction of signal strength in (NHM_THRESHOLD4, NHM_THRESHOLD5]. |
| NHM_RPI_COUNTER6 = 0x26A, // Noise Histogram RPI counter6, the fraction of signal strength in (NHM_THRESHOLD5, NHM_THRESHOLD6]. |
| NHM_RPI_COUNTER7 = 0x26B, // Noise Histogram RPI counter7, the fraction of signal strength in (NHM_THRESHOLD6, NHM_THRESHOLD7]. |
| #define BW_OPMODE_11J BIT(0) |
| #define BW_OPMODE_5G BIT(1) |
| #define BW_OPMODE_20MHZ BIT(2) |
| BW_OPMODE = 0x300, // Bandwidth operation mode |
| MSR = 0x303, // Media Status register |
| #define MSR_LINK_MASK (BIT(0)|BIT(1)) |
| #define MSR_LINK_MANAGED 2 |
| #define MSR_LINK_NONE 0 |
| #define MSR_LINK_SHIFT 0 |
| #define MSR_LINK_ADHOC 1 |
| #define MSR_LINK_MASTER 3 |
| #define MSR_LINK_ENEDCA BIT(4) |
| RETRY_LIMIT = 0x304, // Retry Limit [15:8]-short, [7:0]-long |
| #define RETRY_LIMIT_SHORT_SHIFT 8 |
| #define RETRY_LIMIT_LONG_SHIFT 0 |
| TSFR = 0x308, |
| RRSR = 0x310, // Response Rate Set |
| #define RRSR_RSC_OFFSET 21 |
| #define RRSR_SHORT_OFFSET 23 |
| #define RRSR_RSC_DUPLICATE 0x600000 |
| #define RRSR_RSC_LOWSUBCHNL 0x400000 |
| #define RRSR_RSC_UPSUBCHANL 0x200000 |
| #define RRSR_SHORT 0x800000 |
| #define RRSR_1M BIT(0) |
| #define RRSR_2M BIT(1) |
| #define RRSR_5_5M BIT(2) |
| #define RRSR_11M BIT(3) |
| #define RRSR_6M BIT(4) |
| #define RRSR_9M BIT(5) |
| #define RRSR_12M BIT(6) |
| #define RRSR_18M BIT(7) |
| #define RRSR_24M BIT(8) |
| #define RRSR_36M BIT(9) |
| #define RRSR_48M BIT(10) |
| #define RRSR_54M BIT(11) |
| #define RRSR_MCS0 BIT(12) |
| #define RRSR_MCS1 BIT(13) |
| #define RRSR_MCS2 BIT(14) |
| #define RRSR_MCS3 BIT(15) |
| #define RRSR_MCS4 BIT(16) |
| #define RRSR_MCS5 BIT(17) |
| #define RRSR_MCS6 BIT(18) |
| #define RRSR_MCS7 BIT(19) |
| #define BRSR_AckShortPmb BIT(23) // CCK ACK: use Short Preamble or not. |
| RATR0 = 0x320, // Rate Adaptive Table register1 |
| UFWP = 0x318, |
| DRIVER_RSSI = 0x32c, // Driver tell Firmware current RSSI |
| //---------------------------------------------------------------------------- |
| // 8190 Rate Adaptive Table Register (offset 0x320, 4 byte) |
| //---------------------------------------------------------------------------- |
| //CCK |
| #define RATR_1M 0x00000001 |
| #define RATR_2M 0x00000002 |
| #define RATR_55M 0x00000004 |
| #define RATR_11M 0x00000008 |
| //OFDM |
| #define RATR_6M 0x00000010 |
| #define RATR_9M 0x00000020 |
| #define RATR_12M 0x00000040 |
| #define RATR_18M 0x00000080 |
| #define RATR_24M 0x00000100 |
| #define RATR_36M 0x00000200 |
| #define RATR_48M 0x00000400 |
| #define RATR_54M 0x00000800 |
| //MCS 1 Spatial Stream |
| #define RATR_MCS0 0x00001000 |
| #define RATR_MCS1 0x00002000 |
| #define RATR_MCS2 0x00004000 |
| #define RATR_MCS3 0x00008000 |
| #define RATR_MCS4 0x00010000 |
| #define RATR_MCS5 0x00020000 |
| #define RATR_MCS6 0x00040000 |
| #define RATR_MCS7 0x00080000 |
| //MCS 2 Spatial Stream |
| #define RATR_MCS8 0x00100000 |
| #define RATR_MCS9 0x00200000 |
| #define RATR_MCS10 0x00400000 |
| #define RATR_MCS11 0x00800000 |
| #define RATR_MCS12 0x01000000 |
| #define RATR_MCS13 0x02000000 |
| #define RATR_MCS14 0x04000000 |
| #define RATR_MCS15 0x08000000 |
| // ALL CCK Rate |
| #define RATE_ALL_CCK RATR_1M|RATR_2M|RATR_55M|RATR_11M |
| #define RATE_ALL_OFDM_AG RATR_6M|RATR_9M|RATR_12M|RATR_18M|RATR_24M\ |
| |RATR_36M|RATR_48M|RATR_54M |
| #define RATE_ALL_OFDM_1SS RATR_MCS0|RATR_MCS1|RATR_MCS2|RATR_MCS3 | \ |
| RATR_MCS4|RATR_MCS5|RATR_MCS6|RATR_MCS7 |
| #define RATE_ALL_OFDM_2SS RATR_MCS8|RATR_MCS9 |RATR_MCS10|RATR_MCS11| \ |
| RATR_MCS12|RATR_MCS13|RATR_MCS14|RATR_MCS15 |
| |
| MCS_TXAGC = 0x340, // MCS AGC |
| CCK_TXAGC = 0x348, // CCK AGC |
| // ISR = 0x350, // Interrupt Status Register |
| // IMR = 0x354, // Interrupt Mask Register |
| // IMR_POLL = 0x360, |
| MacBlkCtrl = 0x403, // Mac block on/off control register |
| |
| EPROM_CMD = 0xfe58, |
| #define Cmd9346CR_9356SEL BIT(4) |
| #define EPROM_CMD_RESERVED_MASK BIT(5) |
| #define EPROM_CMD_OPERATING_MODE_SHIFT 6 |
| #define EPROM_CMD_OPERATING_MODE_MASK (BIT(7) | BIT(6)) |
| #define EPROM_CMD_CONFIG 0x3 |
| #define EPROM_CMD_NORMAL 0 |
| #define EPROM_CMD_LOAD 1 |
| #define EPROM_CMD_PROGRAM 2 |
| #define EPROM_CS_BIT BIT(3) |
| #define EPROM_CK_BIT BIT(2) |
| #define EPROM_W_BIT BIT(1) |
| #define EPROM_R_BIT BIT(0) |
| |
| MAC0 = 0x000, |
| MAC1 = 0x001, |
| MAC2 = 0x002, |
| MAC3 = 0x003, |
| MAC4 = 0x004, |
| MAC5 = 0x005, |
| |
| }; |
| //---------------------------------------------------------------------------- |
| // 818xB AnaParm & AnaParm2 Register |
| //---------------------------------------------------------------------------- |
| //#define ANAPARM_ASIC_ON 0x45090658 |
| //#define ANAPARM2_ASIC_ON 0x727f3f52 |
| #define GPI 0x108 |
| #define GPO 0x109 |
| #define GPE 0x10a |
| #endif |
