/*
 *************************************************************************
 * Ralink Tech Inc.
 * 5F., No.36, Taiyuan St., Jhubei City,
 * Hsinchu County 302,
 * Taiwan, R.O.C.
 *
 * (c) Copyright 2002-2007, Ralink Technology, Inc.
 *
 * This program is free software; you can redistribute it and/or modify  *
 * it under the terms of the GNU General Public License as published by  *
 * the Free Software Foundation; either version 2 of the License, or     *
 * (at your option) any later version.                                   *
 *                                                                       *
 * This program is distributed in the hope that it will be useful,       *
 * but WITHOUT ANY WARRANTY; without even the implied warranty of        *
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the         *
 * GNU General Public License for more details.                          *
 *                                                                       *
 * You should have received a copy of the GNU General Public License     *
 * along with this program; if not, write to the                         *
 * Free Software Foundation, Inc.,                                       *
 * 59 Temple Place - Suite 330, Boston, MA  02111-1307, USA.             *
 *                                                                       *
 *************************************************************************

	Module Name:
	rtmp_init.c

	Abstract:
	Miniport generic portion header file

	Revision History:
	Who         When          What
	--------    ----------    ----------------------------------------------
*/

#include "../rt_config.h"


UCHAR    BIT8[] = {0x01, 0x02, 0x04, 0x08, 0x10, 0x20, 0x40, 0x80};
char*   CipherName[] = {"none","wep64","wep128","TKIP","AES","CKIP64","CKIP128"};

//
// BBP register initialization set
//
REG_PAIR   BBPRegTable[] = {
	{BBP_R65,		0x2C},		// fix rssi issue
	{BBP_R66,		0x38},	// Also set this default value to pAd->BbpTuning.R66CurrentValue at initial
	{BBP_R69,		0x12},
	{BBP_R70,		0xa},	// BBP_R70 will change to 0x8 in ApStartUp and LinkUp for rt2860C, otherwise value is 0xa
	{BBP_R73,		0x10},
	{BBP_R81,		0x37},
	{BBP_R82,		0x62},
	{BBP_R83,		0x6A},
	{BBP_R84,		0x99},	// 0x19 is for rt2860E and after. This is for extension channel overlapping IOT. 0x99 is for rt2860D and before
	{BBP_R86,		0x00},	// middle range issue, Rory @2008-01-28
	{BBP_R91,		0x04},	// middle range issue, Rory @2008-01-28
	{BBP_R92,		0x00},	// middle range issue, Rory @2008-01-28
	{BBP_R103,		0x00},	// near range high-power issue, requested from Gary @2008-0528
	{BBP_R105,		0x05},	// 0x05 is for rt2860E to turn on FEQ control. It is safe for rt2860D and before, because Bit 7:2 are reserved in rt2860D and before.
	{BBP_R106,		0x35},  // for ShortGI throughput
};
#define	NUM_BBP_REG_PARMS	(sizeof(BBPRegTable) / sizeof(REG_PAIR))


//
// ASIC register initialization sets
//

RTMP_REG_PAIR	MACRegTable[] =	{
#if defined(HW_BEACON_OFFSET) && (HW_BEACON_OFFSET == 0x200)
	{BCN_OFFSET0,			0xf8f0e8e0}, /* 0x3800(e0), 0x3A00(e8), 0x3C00(f0), 0x3E00(f8), 512B for each beacon */
	{BCN_OFFSET1,			0x6f77d0c8}, /* 0x3200(c8), 0x3400(d0), 0x1DC0(77), 0x1BC0(6f), 512B for each beacon */
#elif defined(HW_BEACON_OFFSET) && (HW_BEACON_OFFSET == 0x100)
	{BCN_OFFSET0,			0xece8e4e0}, /* 0x3800, 0x3A00, 0x3C00, 0x3E00, 512B for each beacon */
	{BCN_OFFSET1,			0xfcf8f4f0}, /* 0x3800, 0x3A00, 0x3C00, 0x3E00, 512B for each beacon */
#else
    #error You must re-calculate new value for BCN_OFFSET0 & BCN_OFFSET1 in MACRegTable[]!!!
#endif // HW_BEACON_OFFSET //

	{LEGACY_BASIC_RATE,		0x0000013f}, //  Basic rate set bitmap
	{HT_BASIC_RATE,		0x00008003}, // Basic HT rate set , 20M, MCS=3, MM. Format is the same as in TXWI.
	{MAC_SYS_CTRL,		0x00}, // 0x1004, , default Disable RX
	{RX_FILTR_CFG,		0x17f97}, //0x1400  , RX filter control,
	{BKOFF_SLOT_CFG,	0x209}, // default set short slot time, CC_DELAY_TIME should be 2
	//{TX_SW_CFG0,		0x40a06}, // Gary,2006-08-23
	{TX_SW_CFG0,		0x0},		// Gary,2008-05-21 for CWC test
	{TX_SW_CFG1,		0x80606}, // Gary,2006-08-23
	{TX_LINK_CFG,		0x1020},		// Gary,2006-08-23
	//{TX_TIMEOUT_CFG,	0x00182090},	// CCK has some problem. So increase timieout value. 2006-10-09// MArvek RT
	{TX_TIMEOUT_CFG,	0x000a2090},	// CCK has some problem. So increase timieout value. 2006-10-09// MArvek RT , Modify for 2860E ,2007-08-01
	{MAX_LEN_CFG,		MAX_AGGREGATION_SIZE | 0x00001000},	// 0x3018, MAX frame length. Max PSDU = 16kbytes.
	{LED_CFG,		0x7f031e46}, // Gary, 2006-08-23

//#ifdef CONFIG_AP_SUPPORT
//	{WMM_AIFSN_CFG,		0x00001173},
//	{WMM_CWMIN_CFG,		0x00002344},
//	{WMM_CWMAX_CFG,		0x000034a6},
//	{WMM_TXOP0_CFG,		0x00100020},
//	{WMM_TXOP1_CFG,		0x002F0038},
//#endif // CONFIG_AP_SUPPORT //

//#ifdef CONFIG_STA_SUPPORT
//	{WMM_AIFSN_CFG,		0x00002273},
//	{WMM_CWMIN_CFG,		0x00002344},
//	{WMM_CWMAX_CFG,		0x000034aa},
//#endif // CONFIG_STA_SUPPORT //
#ifdef INF_AMAZON_SE
	{PBF_MAX_PCNT,			0x1F3F6F6F},	//iverson modify for usb issue, 2008/09/19
											// 6F + 6F < total page count FE
											// so that RX doesn't occupy TX's buffer space when WMM congestion.
#else
	{PBF_MAX_PCNT,			0x1F3FBF9F},	//0x1F3f7f9f},		//Jan, 2006/04/20
#endif // INF_AMAZON_SE //
	//{TX_RTY_CFG,			0x6bb80408},	// Jan, 2006/11/16
// WMM_ACM_SUPPORT
//	{TX_RTY_CFG,			0x6bb80101},	// sample
	{TX_RTY_CFG,			0x47d01f0f},	// Jan, 2006/11/16, Set TxWI->ACK =0 in Probe Rsp Modify for 2860E ,2007-08-03

	{AUTO_RSP_CFG,			0x00000013},	// Initial Auto_Responder, because QA will turn off Auto-Responder
	{CCK_PROT_CFG,			0x05740003 /*0x01740003*/},	// Initial Auto_Responder, because QA will turn off Auto-Responder. And RTS threshold is enabled.
	{OFDM_PROT_CFG,			0x05740003 /*0x01740003*/},	// Initial Auto_Responder, because QA will turn off Auto-Responder. And RTS threshold is enabled.
	{GF20_PROT_CFG,			0x01744004},    // set 19:18 --> Short NAV for MIMO PS
	{GF40_PROT_CFG,			0x03F44084},
	{MM20_PROT_CFG,			0x01744004},
#ifdef RTMP_MAC_PCI
	{MM40_PROT_CFG,			0x03F54084},
#endif // RTMP_MAC_PCI //
	{TXOP_CTRL_CFG,			0x0000583f, /*0x0000243f*/ /*0x000024bf*/},	//Extension channel backoff.
	{TX_RTS_CFG,			0x00092b20},
//#ifdef WIFI_TEST
	{EXP_ACK_TIME,			0x002400ca},	// default value
//#else
//	{EXP_ACK_TIME,			0x005400ca},	// suggested by Gray @ 20070323 for 11n intel-sta throughput
//#endif // end - WIFI_TEST //
//#ifdef CONFIG_AP_SUPPORT
//	{TBTT_SYNC_CFG,			0x00422000},	// TBTT_ADJUST(7:0) == 0
//	{TBTT_SYNC_CFG,			0x00012000},	// TBTT_ADJUST(7:0) == 0
//#endif // CONFIG_AP_SUPPORT //
	{TXOP_HLDR_ET,			0x00000002},

	/* Jerry comments 2008/01/16: we use SIFS = 10us in CCK defaultly, but it seems that 10us
		is too small for INTEL 2200bg card, so in MBSS mode, the delta time between beacon0
		and beacon1 is SIFS (10us), so if INTEL 2200bg card connects to BSS0, the ping
		will always lost. So we change the SIFS of CCK from 10us to 16us. */
	{XIFS_TIME_CFG,			0x33a41010},
	{PWR_PIN_CFG,			0x00000003},	// patch for 2880-E
};


#ifdef CONFIG_STA_SUPPORT
RTMP_REG_PAIR	STAMACRegTable[] =	{
	{WMM_AIFSN_CFG,		0x00002273},
	{WMM_CWMIN_CFG,	0x00002344},
	{WMM_CWMAX_CFG,	0x000034aa},
};
#endif // CONFIG_STA_SUPPORT //

#define	NUM_MAC_REG_PARMS		(sizeof(MACRegTable) / sizeof(RTMP_REG_PAIR))
#ifdef CONFIG_STA_SUPPORT
#define	NUM_STA_MAC_REG_PARMS	(sizeof(STAMACRegTable) / sizeof(RTMP_REG_PAIR))
#endif // CONFIG_STA_SUPPORT //


/*
	========================================================================

	Routine Description:
		Allocate RTMP_ADAPTER data block and do some initialization

	Arguments:
		Adapter		Pointer to our adapter

	Return Value:
		NDIS_STATUS_SUCCESS
		NDIS_STATUS_FAILURE

	IRQL = PASSIVE_LEVEL

	Note:

	========================================================================
*/
NDIS_STATUS	RTMPAllocAdapterBlock(
	IN  PVOID	handle,
	OUT	PRTMP_ADAPTER	*ppAdapter)
{
	PRTMP_ADAPTER	pAd;
	NDIS_STATUS		Status;
	INT			index;
	UCHAR			*pBeaconBuf = NULL;

	DBGPRINT(RT_DEBUG_TRACE, ("--> RTMPAllocAdapterBlock\n"));

	*ppAdapter = NULL;

	do
	{
		// Allocate RTMP_ADAPTER memory block
		pBeaconBuf = kmalloc(MAX_BEACON_SIZE, MEM_ALLOC_FLAG);
		if (pBeaconBuf == NULL)
		{
			Status = NDIS_STATUS_FAILURE;
			DBGPRINT_ERR(("Failed to allocate memory - BeaconBuf!\n"));
			break;
		}
		NdisZeroMemory(pBeaconBuf, MAX_BEACON_SIZE);

		Status = AdapterBlockAllocateMemory(handle, (PVOID *)&pAd);
		if (Status != NDIS_STATUS_SUCCESS)
		{
			DBGPRINT_ERR(("Failed to allocate memory - ADAPTER\n"));
			break;
		}
		pAd->BeaconBuf = pBeaconBuf;
		DBGPRINT(RT_DEBUG_OFF, ("\n\n=== pAd = %p, size = %d ===\n\n", pAd, (UINT32)sizeof(RTMP_ADAPTER)));


		// Init spin locks
		NdisAllocateSpinLock(&pAd->MgmtRingLock);
#ifdef RTMP_MAC_PCI
		NdisAllocateSpinLock(&pAd->RxRingLock);
#ifdef RT3090
#ifdef CONFIG_STA_SUPPORT
	NdisAllocateSpinLock(&pAd->McuCmdLock);
#endif // CONFIG_STA_SUPPORT //
#endif // RT3090 //
#endif // RTMP_MAC_PCI //

		for (index =0 ; index < NUM_OF_TX_RING; index++)
		{
			NdisAllocateSpinLock(&pAd->TxSwQueueLock[index]);
			NdisAllocateSpinLock(&pAd->DeQueueLock[index]);
			pAd->DeQueueRunning[index] = FALSE;
		}

		NdisAllocateSpinLock(&pAd->irq_lock);


	} while (FALSE);

	if ((Status != NDIS_STATUS_SUCCESS) && (pBeaconBuf))
		kfree(pBeaconBuf);

	*ppAdapter = pAd;

	DBGPRINT_S(Status, ("<-- RTMPAllocAdapterBlock, Status=%x\n", Status));
	return Status;
}


/*
	========================================================================

	Routine Description:
		Read initial Tx power per MCS and BW from EEPROM

	Arguments:
		Adapter						Pointer to our adapter

	Return Value:
		None

	IRQL = PASSIVE_LEVEL

	Note:

	========================================================================
*/
VOID	RTMPReadTxPwrPerRate(
	IN	PRTMP_ADAPTER	pAd)
{
	ULONG		data, Adata, Gdata;
	USHORT		i, value, value2;
	INT			Apwrdelta, Gpwrdelta;
	UCHAR		t1,t2,t3,t4;
	BOOLEAN		bApwrdeltaMinus = TRUE, bGpwrdeltaMinus = TRUE;

	//
	// Get power delta for 20MHz and 40MHz.
	//
	DBGPRINT(RT_DEBUG_TRACE, ("Txpower per Rate\n"));
	RT28xx_EEPROM_READ16(pAd, EEPROM_TXPOWER_DELTA, value2);
	Apwrdelta = 0;
	Gpwrdelta = 0;

	if ((value2 & 0xff) != 0xff)
	{
		if ((value2 & 0x80))
			Gpwrdelta = (value2&0xf);

		if ((value2 & 0x40))
			bGpwrdeltaMinus = FALSE;
		else
			bGpwrdeltaMinus = TRUE;
	}
	if ((value2 & 0xff00) != 0xff00)
	{
		if ((value2 & 0x8000))
			Apwrdelta = ((value2&0xf00)>>8);

		if ((value2 & 0x4000))
			bApwrdeltaMinus = FALSE;
		else
			bApwrdeltaMinus = TRUE;
	}
	DBGPRINT(RT_DEBUG_TRACE, ("Gpwrdelta = %x, Apwrdelta = %x .\n", Gpwrdelta, Apwrdelta));

	//
	// Get Txpower per MCS for 20MHz in 2.4G.
	//
	for (i=0; i<5; i++)
	{
		RT28xx_EEPROM_READ16(pAd, EEPROM_TXPOWER_BYRATE_20MHZ_2_4G + i*4, value);
		data = value;
		if (bApwrdeltaMinus == FALSE)
		{
			t1 = (value&0xf)+(Apwrdelta);
			if (t1 > 0xf)
				t1 = 0xf;
			t2 = ((value&0xf0)>>4)+(Apwrdelta);
			if (t2 > 0xf)
				t2 = 0xf;
			t3 = ((value&0xf00)>>8)+(Apwrdelta);
			if (t3 > 0xf)
				t3 = 0xf;
			t4 = ((value&0xf000)>>12)+(Apwrdelta);
			if (t4 > 0xf)
				t4 = 0xf;
		}
		else
		{
			if ((value&0xf) > Apwrdelta)
				t1 = (value&0xf)-(Apwrdelta);
			else
				t1 = 0;
			if (((value&0xf0)>>4) > Apwrdelta)
				t2 = ((value&0xf0)>>4)-(Apwrdelta);
			else
				t2 = 0;
			if (((value&0xf00)>>8) > Apwrdelta)
				t3 = ((value&0xf00)>>8)-(Apwrdelta);
			else
				t3 = 0;
			if (((value&0xf000)>>12) > Apwrdelta)
				t4 = ((value&0xf000)>>12)-(Apwrdelta);
			else
				t4 = 0;
		}
		Adata = t1 + (t2<<4) + (t3<<8) + (t4<<12);
		if (bGpwrdeltaMinus == FALSE)
		{
			t1 = (value&0xf)+(Gpwrdelta);
			if (t1 > 0xf)
				t1 = 0xf;
			t2 = ((value&0xf0)>>4)+(Gpwrdelta);
			if (t2 > 0xf)
				t2 = 0xf;
			t3 = ((value&0xf00)>>8)+(Gpwrdelta);
			if (t3 > 0xf)
				t3 = 0xf;
			t4 = ((value&0xf000)>>12)+(Gpwrdelta);
			if (t4 > 0xf)
				t4 = 0xf;
		}
		else
		{
			if ((value&0xf) > Gpwrdelta)
				t1 = (value&0xf)-(Gpwrdelta);
			else
				t1 = 0;
			if (((value&0xf0)>>4) > Gpwrdelta)
				t2 = ((value&0xf0)>>4)-(Gpwrdelta);
			else
				t2 = 0;
			if (((value&0xf00)>>8) > Gpwrdelta)
				t3 = ((value&0xf00)>>8)-(Gpwrdelta);
			else
				t3 = 0;
			if (((value&0xf000)>>12) > Gpwrdelta)
				t4 = ((value&0xf000)>>12)-(Gpwrdelta);
			else
				t4 = 0;
		}
		Gdata = t1 + (t2<<4) + (t3<<8) + (t4<<12);

		RT28xx_EEPROM_READ16(pAd, EEPROM_TXPOWER_BYRATE_20MHZ_2_4G + i*4 + 2, value);
		if (bApwrdeltaMinus == FALSE)
		{
			t1 = (value&0xf)+(Apwrdelta);
			if (t1 > 0xf)
				t1 = 0xf;
			t2 = ((value&0xf0)>>4)+(Apwrdelta);
			if (t2 > 0xf)
				t2 = 0xf;
			t3 = ((value&0xf00)>>8)+(Apwrdelta);
			if (t3 > 0xf)
				t3 = 0xf;
			t4 = ((value&0xf000)>>12)+(Apwrdelta);
			if (t4 > 0xf)
				t4 = 0xf;
		}
		else
		{
			if ((value&0xf) > Apwrdelta)
				t1 = (value&0xf)-(Apwrdelta);
			else
				t1 = 0;
			if (((value&0xf0)>>4) > Apwrdelta)
				t2 = ((value&0xf0)>>4)-(Apwrdelta);
			else
				t2 = 0;
			if (((value&0xf00)>>8) > Apwrdelta)
				t3 = ((value&0xf00)>>8)-(Apwrdelta);
			else
				t3 = 0;
			if (((value&0xf000)>>12) > Apwrdelta)
				t4 = ((value&0xf000)>>12)-(Apwrdelta);
			else
				t4 = 0;
		}
		Adata |= ((t1<<16) + (t2<<20) + (t3<<24) + (t4<<28));
		if (bGpwrdeltaMinus == FALSE)
		{
			t1 = (value&0xf)+(Gpwrdelta);
			if (t1 > 0xf)
				t1 = 0xf;
			t2 = ((value&0xf0)>>4)+(Gpwrdelta);
			if (t2 > 0xf)
				t2 = 0xf;
			t3 = ((value&0xf00)>>8)+(Gpwrdelta);
			if (t3 > 0xf)
				t3 = 0xf;
			t4 = ((value&0xf000)>>12)+(Gpwrdelta);
			if (t4 > 0xf)
				t4 = 0xf;
		}
		else
		{
			if ((value&0xf) > Gpwrdelta)
				t1 = (value&0xf)-(Gpwrdelta);
			else
				t1 = 0;
			if (((value&0xf0)>>4) > Gpwrdelta)
				t2 = ((value&0xf0)>>4)-(Gpwrdelta);
			else
				t2 = 0;
			if (((value&0xf00)>>8) > Gpwrdelta)
				t3 = ((value&0xf00)>>8)-(Gpwrdelta);
			else
				t3 = 0;
			if (((value&0xf000)>>12) > Gpwrdelta)
				t4 = ((value&0xf000)>>12)-(Gpwrdelta);
			else
				t4 = 0;
		}
		Gdata |= ((t1<<16) + (t2<<20) + (t3<<24) + (t4<<28));
		data |= (value<<16);

		/* For 20M/40M Power Delta issue */
		pAd->Tx20MPwrCfgABand[i] = data;
		pAd->Tx20MPwrCfgGBand[i] = data;
		pAd->Tx40MPwrCfgABand[i] = Adata;
		pAd->Tx40MPwrCfgGBand[i] = Gdata;

		if (data != 0xffffffff)
			RTMP_IO_WRITE32(pAd, TX_PWR_CFG_0 + i*4, data);
		DBGPRINT_RAW(RT_DEBUG_TRACE, ("20MHz BW, 2.4G band-%lx,  Adata = %lx,  Gdata = %lx \n", data, Adata, Gdata));
	}
}


/*
	========================================================================

	Routine Description:
		Read initial channel power parameters from EEPROM

	Arguments:
		Adapter						Pointer to our adapter

	Return Value:
		None

	IRQL = PASSIVE_LEVEL

	Note:

	========================================================================
*/
VOID	RTMPReadChannelPwr(
	IN	PRTMP_ADAPTER	pAd)
{
	UCHAR				i, choffset;
	EEPROM_TX_PWR_STRUC	    Power;
	EEPROM_TX_PWR_STRUC	    Power2;

	// Read Tx power value for all channels
	// Value from 1 - 0x7f. Default value is 24.
	// Power value : 2.4G 0x00 (0) ~ 0x1F (31)
	//             : 5.5G 0xF9 (-7) ~ 0x0F (15)

	// 0. 11b/g, ch1 - ch 14
	for (i = 0; i < 7; i++)
	{
		RT28xx_EEPROM_READ16(pAd, EEPROM_G_TX_PWR_OFFSET + i * 2, Power.word);
		RT28xx_EEPROM_READ16(pAd, EEPROM_G_TX2_PWR_OFFSET + i * 2, Power2.word);
		pAd->TxPower[i * 2].Channel = i * 2 + 1;
		pAd->TxPower[i * 2 + 1].Channel = i * 2 + 2;

		if ((Power.field.Byte0 > 31) || (Power.field.Byte0 < 0))
			pAd->TxPower[i * 2].Power = DEFAULT_RF_TX_POWER;
		else
			pAd->TxPower[i * 2].Power = Power.field.Byte0;

		if ((Power.field.Byte1 > 31) || (Power.field.Byte1 < 0))
			pAd->TxPower[i * 2 + 1].Power = DEFAULT_RF_TX_POWER;
		else
			pAd->TxPower[i * 2 + 1].Power = Power.field.Byte1;

		if ((Power2.field.Byte0 > 31) || (Power2.field.Byte0 < 0))
			pAd->TxPower[i * 2].Power2 = DEFAULT_RF_TX_POWER;
		else
			pAd->TxPower[i * 2].Power2 = Power2.field.Byte0;

		if ((Power2.field.Byte1 > 31) || (Power2.field.Byte1 < 0))
			pAd->TxPower[i * 2 + 1].Power2 = DEFAULT_RF_TX_POWER;
		else
			pAd->TxPower[i * 2 + 1].Power2 = Power2.field.Byte1;
	}

	// 1. U-NII lower/middle band: 36, 38, 40; 44, 46, 48; 52, 54, 56; 60, 62, 64 (including central frequency in BW 40MHz)
	// 1.1 Fill up channel
	choffset = 14;
	for (i = 0; i < 4; i++)
	{
		pAd->TxPower[3 * i + choffset + 0].Channel	= 36 + i * 8 + 0;
		pAd->TxPower[3 * i + choffset + 0].Power	= DEFAULT_RF_TX_POWER;
		pAd->TxPower[3 * i + choffset + 0].Power2	= DEFAULT_RF_TX_POWER;

		pAd->TxPower[3 * i + choffset + 1].Channel	= 36 + i * 8 + 2;
		pAd->TxPower[3 * i + choffset + 1].Power	= DEFAULT_RF_TX_POWER;
		pAd->TxPower[3 * i + choffset + 1].Power2	= DEFAULT_RF_TX_POWER;

		pAd->TxPower[3 * i + choffset + 2].Channel	= 36 + i * 8 + 4;
		pAd->TxPower[3 * i + choffset + 2].Power	= DEFAULT_RF_TX_POWER;
		pAd->TxPower[3 * i + choffset + 2].Power2	= DEFAULT_RF_TX_POWER;
	}

	// 1.2 Fill up power
	for (i = 0; i < 6; i++)
	{
		RT28xx_EEPROM_READ16(pAd, EEPROM_A_TX_PWR_OFFSET + i * 2, Power.word);
		RT28xx_EEPROM_READ16(pAd, EEPROM_A_TX2_PWR_OFFSET + i * 2, Power2.word);

		if ((Power.field.Byte0 < 16) && (Power.field.Byte0 >= -7))
			pAd->TxPower[i * 2 + choffset + 0].Power = Power.field.Byte0;

		if ((Power.field.Byte1 < 16) && (Power.field.Byte1 >= -7))
			pAd->TxPower[i * 2 + choffset + 1].Power = Power.field.Byte1;

		if ((Power2.field.Byte0 < 16) && (Power2.field.Byte0 >= -7))
			pAd->TxPower[i * 2 + choffset + 0].Power2 = Power2.field.Byte0;

		if ((Power2.field.Byte1 < 16) && (Power2.field.Byte1 >= -7))
			pAd->TxPower[i * 2 + choffset + 1].Power2 = Power2.field.Byte1;
	}

	// 2. HipperLAN 2 100, 102 ,104; 108, 110, 112; 116, 118, 120; 124, 126, 128; 132, 134, 136; 140 (including central frequency in BW 40MHz)
	// 2.1 Fill up channel
	choffset = 14 + 12;
	for (i = 0; i < 5; i++)
	{
		pAd->TxPower[3 * i + choffset + 0].Channel	= 100 + i * 8 + 0;
		pAd->TxPower[3 * i + choffset + 0].Power	= DEFAULT_RF_TX_POWER;
		pAd->TxPower[3 * i + choffset + 0].Power2	= DEFAULT_RF_TX_POWER;

		pAd->TxPower[3 * i + choffset + 1].Channel	= 100 + i * 8 + 2;
		pAd->TxPower[3 * i + choffset + 1].Power	= DEFAULT_RF_TX_POWER;
		pAd->TxPower[3 * i + choffset + 1].Power2	= DEFAULT_RF_TX_POWER;

		pAd->TxPower[3 * i + choffset + 2].Channel	= 100 + i * 8 + 4;
		pAd->TxPower[3 * i + choffset + 2].Power	= DEFAULT_RF_TX_POWER;
		pAd->TxPower[3 * i + choffset + 2].Power2	= DEFAULT_RF_TX_POWER;
	}
	pAd->TxPower[3 * 5 + choffset + 0].Channel		= 140;
	pAd->TxPower[3 * 5 + choffset + 0].Power		= DEFAULT_RF_TX_POWER;
	pAd->TxPower[3 * 5 + choffset + 0].Power2		= DEFAULT_RF_TX_POWER;

	// 2.2 Fill up power
	for (i = 0; i < 8; i++)
	{
		RT28xx_EEPROM_READ16(pAd, EEPROM_A_TX_PWR_OFFSET + (choffset - 14) + i * 2, Power.word);
		RT28xx_EEPROM_READ16(pAd, EEPROM_A_TX2_PWR_OFFSET + (choffset - 14) + i * 2, Power2.word);

		if ((Power.field.Byte0 < 16) && (Power.field.Byte0 >= -7))
			pAd->TxPower[i * 2 + choffset + 0].Power = Power.field.Byte0;

		if ((Power.field.Byte1 < 16) && (Power.field.Byte1 >= -7))
			pAd->TxPower[i * 2 + choffset + 1].Power = Power.field.Byte1;

		if ((Power2.field.Byte0 < 16) && (Power2.field.Byte0 >= -7))
			pAd->TxPower[i * 2 + choffset + 0].Power2 = Power2.field.Byte0;

		if ((Power2.field.Byte1 < 16) && (Power2.field.Byte1 >= -7))
			pAd->TxPower[i * 2 + choffset + 1].Power2 = Power2.field.Byte1;
	}

	// 3. U-NII upper band: 149, 151, 153; 157, 159, 161; 165, 167, 169; 171, 173 (including central frequency in BW 40MHz)
	// 3.1 Fill up channel
	choffset = 14 + 12 + 16;
	/*for (i = 0; i < 2; i++)*/
	for (i = 0; i < 3; i++)
	{
		pAd->TxPower[3 * i + choffset + 0].Channel	= 149 + i * 8 + 0;
		pAd->TxPower[3 * i + choffset + 0].Power	= DEFAULT_RF_TX_POWER;
		pAd->TxPower[3 * i + choffset + 0].Power2	= DEFAULT_RF_TX_POWER;

		pAd->TxPower[3 * i + choffset + 1].Channel	= 149 + i * 8 + 2;
		pAd->TxPower[3 * i + choffset + 1].Power	= DEFAULT_RF_TX_POWER;
		pAd->TxPower[3 * i + choffset + 1].Power2	= DEFAULT_RF_TX_POWER;

		pAd->TxPower[3 * i + choffset + 2].Channel	= 149 + i * 8 + 4;
		pAd->TxPower[3 * i + choffset + 2].Power	= DEFAULT_RF_TX_POWER;
		pAd->TxPower[3 * i + choffset + 2].Power2	= DEFAULT_RF_TX_POWER;
	}
	pAd->TxPower[3 * 3 + choffset + 0].Channel		= 171;
	pAd->TxPower[3 * 3 + choffset + 0].Power		= DEFAULT_RF_TX_POWER;
	pAd->TxPower[3 * 3 + choffset + 0].Power2		= DEFAULT_RF_TX_POWER;

	pAd->TxPower[3 * 3 + choffset + 1].Channel		= 173;
	pAd->TxPower[3 * 3 + choffset + 1].Power		= DEFAULT_RF_TX_POWER;
	pAd->TxPower[3 * 3 + choffset + 1].Power2		= DEFAULT_RF_TX_POWER;

	// 3.2 Fill up power
	/*for (i = 0; i < 4; i++)*/
	for (i = 0; i < 6; i++)
	{
		RT28xx_EEPROM_READ16(pAd, EEPROM_A_TX_PWR_OFFSET + (choffset - 14) + i * 2, Power.word);
		RT28xx_EEPROM_READ16(pAd, EEPROM_A_TX2_PWR_OFFSET + (choffset - 14) + i * 2, Power2.word);

		if ((Power.field.Byte0 < 16) && (Power.field.Byte0 >= -7))
			pAd->TxPower[i * 2 + choffset + 0].Power = Power.field.Byte0;

		if ((Power.field.Byte1 < 16) && (Power.field.Byte1 >= -7))
			pAd->TxPower[i * 2 + choffset + 1].Power = Power.field.Byte1;

		if ((Power2.field.Byte0 < 16) && (Power2.field.Byte0 >= -7))
			pAd->TxPower[i * 2 + choffset + 0].Power2 = Power2.field.Byte0;

		if ((Power2.field.Byte1 < 16) && (Power2.field.Byte1 >= -7))
			pAd->TxPower[i * 2 + choffset + 1].Power2 = Power2.field.Byte1;
	}

	// 4. Print and Debug
	/*choffset = 14 + 12 + 16 + 7;*/
	choffset = 14 + 12 + 16 + 11;


}

/*
	========================================================================

	Routine Description:
		Read the following from the registry
		1. All the parameters
		2. NetworkAddres

	Arguments:
		Adapter						Pointer to our adapter
		WrapperConfigurationContext	For use by NdisOpenConfiguration

	Return Value:
		NDIS_STATUS_SUCCESS
		NDIS_STATUS_FAILURE
		NDIS_STATUS_RESOURCES

	IRQL = PASSIVE_LEVEL

	Note:

	========================================================================
*/
NDIS_STATUS	NICReadRegParameters(
	IN	PRTMP_ADAPTER		pAd,
	IN	NDIS_HANDLE			WrapperConfigurationContext
	)
{
	NDIS_STATUS						Status = NDIS_STATUS_SUCCESS;
	DBGPRINT_S(Status, ("<-- NICReadRegParameters, Status=%x\n", Status));
	return Status;
}


/*
	========================================================================

	Routine Description:
		Read initial parameters from EEPROM

	Arguments:
		Adapter						Pointer to our adapter

	Return Value:
		None

	IRQL = PASSIVE_LEVEL

	Note:

	========================================================================
*/
VOID	NICReadEEPROMParameters(
	IN	PRTMP_ADAPTER	pAd,
	IN	PUCHAR			mac_addr)
{
	UINT32			data = 0;
	USHORT			i, value, value2;
	UCHAR			TmpPhy;
	EEPROM_TX_PWR_STRUC	    Power;
	EEPROM_VERSION_STRUC    Version;
	EEPROM_ANTENNA_STRUC	Antenna;
	EEPROM_NIC_CONFIG2_STRUC    NicConfig2;

	DBGPRINT(RT_DEBUG_TRACE, ("--> NICReadEEPROMParameters\n"));

	if (pAd->chipOps.eeinit)
		pAd->chipOps.eeinit(pAd);
#ifdef RTMP_EFUSE_SUPPORT
#ifdef RT30xx
	if(!pAd->bFroceEEPROMBuffer && pAd->bEEPROMFile)
	{
		DBGPRINT(RT_DEBUG_TRACE, ("--> NICReadEEPROMParameters::(Efuse)Load  to EEPROM Buffer Mode\n"));
		eFuseLoadEEPROM(pAd);
	}
#endif // RT30xx //
#endif // RTMP_EFUSE_SUPPORT //

	// Init EEPROM Address Number, before access EEPROM; if 93c46, EEPROMAddressNum=6, else if 93c66, EEPROMAddressNum=8
	RTMP_IO_READ32(pAd, E2PROM_CSR, &data);
	DBGPRINT(RT_DEBUG_TRACE, ("--> E2PROM_CSR = 0x%x\n", data));

	if((data & 0x30) == 0)
		pAd->EEPROMAddressNum = 6;		// 93C46
	else if((data & 0x30) == 0x10)
		pAd->EEPROMAddressNum = 8;     // 93C66
	else
		pAd->EEPROMAddressNum = 8;     // 93C86
	DBGPRINT(RT_DEBUG_TRACE, ("--> EEPROMAddressNum = %d\n", pAd->EEPROMAddressNum ));

	// RT2860 MAC no longer auto load MAC address from E2PROM. Driver has to intialize
	// MAC address registers according to E2PROM setting
	if (mac_addr == NULL ||
		strlen((PSTRING) mac_addr) != 17 ||
		mac_addr[2] != ':'  || mac_addr[5] != ':'  || mac_addr[8] != ':' ||
		mac_addr[11] != ':' || mac_addr[14] != ':')
	{
		USHORT  Addr01,Addr23,Addr45 ;

		RT28xx_EEPROM_READ16(pAd, 0x04, Addr01);
		RT28xx_EEPROM_READ16(pAd, 0x06, Addr23);
		RT28xx_EEPROM_READ16(pAd, 0x08, Addr45);

		pAd->PermanentAddress[0] = (UCHAR)(Addr01 & 0xff);
		pAd->PermanentAddress[1] = (UCHAR)(Addr01 >> 8);
		pAd->PermanentAddress[2] = (UCHAR)(Addr23 & 0xff);
		pAd->PermanentAddress[3] = (UCHAR)(Addr23 >> 8);
		pAd->PermanentAddress[4] = (UCHAR)(Addr45 & 0xff);
		pAd->PermanentAddress[5] = (UCHAR)(Addr45 >> 8);

		DBGPRINT(RT_DEBUG_TRACE, ("Initialize MAC Address from E2PROM \n"));
	}
	else
	{
		INT		j;
		PSTRING	macptr;

		macptr = (PSTRING) mac_addr;

		for (j=0; j<MAC_ADDR_LEN; j++)
		{
			AtoH(macptr, &pAd->PermanentAddress[j], 1);
			macptr=macptr+3;
		}

		DBGPRINT(RT_DEBUG_TRACE, ("Initialize MAC Address from module parameter \n"));
	}


	{
		//more conveninet to test mbssid, so ap's bssid &0xf1
		if (pAd->PermanentAddress[0] == 0xff)
			pAd->PermanentAddress[0] = RandomByte(pAd)&0xf8;

		//if (pAd->PermanentAddress[5] == 0xff)
		//	pAd->PermanentAddress[5] = RandomByte(pAd)&0xf8;

		DBGPRINT_RAW(RT_DEBUG_TRACE,("E2PROM MAC: =%02x:%02x:%02x:%02x:%02x:%02x\n",
			pAd->PermanentAddress[0], pAd->PermanentAddress[1],
			pAd->PermanentAddress[2], pAd->PermanentAddress[3],
			pAd->PermanentAddress[4], pAd->PermanentAddress[5]));
		if (pAd->bLocalAdminMAC == FALSE)
		{
			MAC_DW0_STRUC csr2;
			MAC_DW1_STRUC csr3;
			COPY_MAC_ADDR(pAd->CurrentAddress, pAd->PermanentAddress);
			csr2.field.Byte0 = pAd->CurrentAddress[0];
			csr2.field.Byte1 = pAd->CurrentAddress[1];
			csr2.field.Byte2 = pAd->CurrentAddress[2];
			csr2.field.Byte3 = pAd->CurrentAddress[3];
			RTMP_IO_WRITE32(pAd, MAC_ADDR_DW0, csr2.word);
			csr3.word = 0;
			csr3.field.Byte4 = pAd->CurrentAddress[4];
			csr3.field.Byte5 = pAd->CurrentAddress[5];
			csr3.field.U2MeMask = 0xff;
			RTMP_IO_WRITE32(pAd, MAC_ADDR_DW1, csr3.word);
			DBGPRINT_RAW(RT_DEBUG_TRACE,("E2PROM MAC: =%02x:%02x:%02x:%02x:%02x:%02x\n",
							PRINT_MAC(pAd->PermanentAddress)));
		}
	}

	// if not return early. cause fail at emulation.
	// Init the channel number for TX channel power
	RTMPReadChannelPwr(pAd);

	// if E2PROM version mismatch with driver's expectation, then skip
	// all subsequent E2RPOM retieval and set a system error bit to notify GUI
	RT28xx_EEPROM_READ16(pAd, EEPROM_VERSION_OFFSET, Version.word);
	pAd->EepromVersion = Version.field.Version + Version.field.FaeReleaseNumber * 256;
	DBGPRINT(RT_DEBUG_TRACE, ("E2PROM: Version = %d, FAE release #%d\n", Version.field.Version, Version.field.FaeReleaseNumber));

	if (Version.field.Version > VALID_EEPROM_VERSION)
	{
		DBGPRINT_ERR(("E2PROM: WRONG VERSION 0x%x, should be %d\n",Version.field.Version, VALID_EEPROM_VERSION));
		/*pAd->SystemErrorBitmap |= 0x00000001;

		// hard-code default value when no proper E2PROM installed
		pAd->bAutoTxAgcA = FALSE;
		pAd->bAutoTxAgcG = FALSE;

		// Default the channel power
		for (i = 0; i < MAX_NUM_OF_CHANNELS; i++)
			pAd->TxPower[i].Power = DEFAULT_RF_TX_POWER;

		// Default the channel power
		for (i = 0; i < MAX_NUM_OF_11JCHANNELS; i++)
			pAd->TxPower11J[i].Power = DEFAULT_RF_TX_POWER;

		for(i = 0; i < NUM_EEPROM_BBP_PARMS; i++)
			pAd->EEPROMDefaultValue[i] = 0xffff;
		return;  */
	}

	// Read BBP default value from EEPROM and store to array(EEPROMDefaultValue) in pAd
	RT28xx_EEPROM_READ16(pAd, EEPROM_NIC1_OFFSET, value);
	pAd->EEPROMDefaultValue[0] = value;

	RT28xx_EEPROM_READ16(pAd, EEPROM_NIC2_OFFSET, value);
	pAd->EEPROMDefaultValue[1] = value;

	RT28xx_EEPROM_READ16(pAd, 0x38, value);	// Country Region
	pAd->EEPROMDefaultValue[2] = value;

	for(i = 0; i < 8; i++)
	{
		RT28xx_EEPROM_READ16(pAd, EEPROM_BBP_BASE_OFFSET + i*2, value);
		pAd->EEPROMDefaultValue[i+3] = value;
	}

	// We have to parse NIC configuration 0 at here.
	// If TSSI did not have preloaded value, it should reset the TxAutoAgc to false
	// Therefore, we have to read TxAutoAgc control beforehand.
	// Read Tx AGC control bit
	Antenna.word = pAd->EEPROMDefaultValue[0];
	if (Antenna.word == 0xFFFF)
	{
#ifdef RT30xx
		if(IS_RT3090(pAd)|| IS_RT3390(pAd))
		{
			Antenna.word = 0;
			Antenna.field.RfIcType = RFIC_3020;
			Antenna.field.TxPath = 1;
			Antenna.field.RxPath = 1;
		}
		else
#endif // RT30xx //
		{

			Antenna.word = 0;
			Antenna.field.RfIcType = RFIC_2820;
			Antenna.field.TxPath = 1;
			Antenna.field.RxPath = 2;
			DBGPRINT(RT_DEBUG_WARN, ("E2PROM error, hard code as 0x%04x\n", Antenna.word));
		}
	}

	// Choose the desired Tx&Rx stream.
	if ((pAd->CommonCfg.TxStream == 0) || (pAd->CommonCfg.TxStream > Antenna.field.TxPath))
		pAd->CommonCfg.TxStream = Antenna.field.TxPath;

	if ((pAd->CommonCfg.RxStream == 0) || (pAd->CommonCfg.RxStream > Antenna.field.RxPath))
	{
		pAd->CommonCfg.RxStream = Antenna.field.RxPath;

		if ((pAd->MACVersion < RALINK_2883_VERSION) &&
			(pAd->CommonCfg.RxStream > 2))
		{
			// only 2 Rx streams for RT2860 series
			pAd->CommonCfg.RxStream = 2;
		}
	}

	// 3*3
	// read value from EEPROM and set them to CSR174 ~ 177 in chain0 ~ chain2
	// yet implement
	for(i=0; i<3; i++)
	{
	}

	NicConfig2.word = pAd->EEPROMDefaultValue[1];


#ifdef CONFIG_STA_SUPPORT
	IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
	{
		if ((NicConfig2.word & 0x00ff) == 0xff)
		{
			NicConfig2.word &= 0xff00;
		}

		if ((NicConfig2.word >> 8) == 0xff)
		{
			NicConfig2.word &= 0x00ff;
		}
	}
#endif // CONFIG_STA_SUPPORT //

	if (NicConfig2.field.DynamicTxAgcControl == 1)
		pAd->bAutoTxAgcA = pAd->bAutoTxAgcG = TRUE;
	else
		pAd->bAutoTxAgcA = pAd->bAutoTxAgcG = FALSE;

	DBGPRINT_RAW(RT_DEBUG_TRACE, ("NICReadEEPROMParameters: RxPath = %d, TxPath = %d\n", Antenna.field.RxPath, Antenna.field.TxPath));

	// Save the antenna for future use
	pAd->Antenna.word = Antenna.word;

	// Set the RfICType here, then we can initialize RFIC related operation callbacks
	pAd->Mlme.RealRxPath = (UCHAR) Antenna.field.RxPath;
	pAd->RfIcType = (UCHAR) Antenna.field.RfIcType;

#ifdef RTMP_RF_RW_SUPPORT
	RtmpChipOpsRFHook(pAd);
#endif // RTMP_RF_RW_SUPPORT //

	//
	// Reset PhyMode if we don't support 802.11a
	// Only RFIC_2850 & RFIC_2750 support 802.11a
	//
	if ((Antenna.field.RfIcType != RFIC_2850)
		&& (Antenna.field.RfIcType != RFIC_2750)
		&& (Antenna.field.RfIcType != RFIC_3052))
	{
		if ((pAd->CommonCfg.PhyMode == PHY_11ABG_MIXED) ||
			(pAd->CommonCfg.PhyMode == PHY_11A))
			pAd->CommonCfg.PhyMode = PHY_11BG_MIXED;
#ifdef DOT11_N_SUPPORT
		else if ((pAd->CommonCfg.PhyMode == PHY_11ABGN_MIXED)	||
				 (pAd->CommonCfg.PhyMode == PHY_11AN_MIXED)	||
				 (pAd->CommonCfg.PhyMode == PHY_11AGN_MIXED)	||
				 (pAd->CommonCfg.PhyMode == PHY_11N_5G))
			pAd->CommonCfg.PhyMode = PHY_11BGN_MIXED;
#endif // DOT11_N_SUPPORT //
	}

	// Read TSSI reference and TSSI boundary for temperature compensation. This is ugly
	// 0. 11b/g
	{
		/* these are tempature reference value (0x00 ~ 0xFE)
		   ex: 0x00 0x15 0x25 0x45 0x88 0xA0 0xB5 0xD0 0xF0
		   TssiPlusBoundaryG [4] [3] [2] [1] [0] (smaller) +
		   TssiMinusBoundaryG[0] [1] [2] [3] [4] (larger) */
		RT28xx_EEPROM_READ16(pAd, 0x6E, Power.word);
		pAd->TssiMinusBoundaryG[4] = Power.field.Byte0;
		pAd->TssiMinusBoundaryG[3] = Power.field.Byte1;
		RT28xx_EEPROM_READ16(pAd, 0x70, Power.word);
		pAd->TssiMinusBoundaryG[2] = Power.field.Byte0;
		pAd->TssiMinusBoundaryG[1] = Power.field.Byte1;
		RT28xx_EEPROM_READ16(pAd, 0x72, Power.word);
		pAd->TssiRefG   = Power.field.Byte0; /* reference value [0] */
		pAd->TssiPlusBoundaryG[1] = Power.field.Byte1;
		RT28xx_EEPROM_READ16(pAd, 0x74, Power.word);
		pAd->TssiPlusBoundaryG[2] = Power.field.Byte0;
		pAd->TssiPlusBoundaryG[3] = Power.field.Byte1;
		RT28xx_EEPROM_READ16(pAd, 0x76, Power.word);
		pAd->TssiPlusBoundaryG[4] = Power.field.Byte0;
		pAd->TxAgcStepG = Power.field.Byte1;
		pAd->TxAgcCompensateG = 0;
		pAd->TssiMinusBoundaryG[0] = pAd->TssiRefG;
		pAd->TssiPlusBoundaryG[0]  = pAd->TssiRefG;

		// Disable TxAgc if the based value is not right
		if (pAd->TssiRefG == 0xff)
			pAd->bAutoTxAgcG = FALSE;

		DBGPRINT(RT_DEBUG_TRACE,("E2PROM: G Tssi[-4 .. +4] = %d %d %d %d - %d -%d %d %d %d, step=%d, tuning=%d\n",
			pAd->TssiMinusBoundaryG[4], pAd->TssiMinusBoundaryG[3], pAd->TssiMinusBoundaryG[2], pAd->TssiMinusBoundaryG[1],
			pAd->TssiRefG,
			pAd->TssiPlusBoundaryG[1], pAd->TssiPlusBoundaryG[2], pAd->TssiPlusBoundaryG[3], pAd->TssiPlusBoundaryG[4],
			pAd->TxAgcStepG, pAd->bAutoTxAgcG));
	}
	// 1. 11a
	{
		RT28xx_EEPROM_READ16(pAd, 0xD4, Power.word);
		pAd->TssiMinusBoundaryA[4] = Power.field.Byte0;
		pAd->TssiMinusBoundaryA[3] = Power.field.Byte1;
		RT28xx_EEPROM_READ16(pAd, 0xD6, Power.word);
		pAd->TssiMinusBoundaryA[2] = Power.field.Byte0;
		pAd->TssiMinusBoundaryA[1] = Power.field.Byte1;
		RT28xx_EEPROM_READ16(pAd, 0xD8, Power.word);
		pAd->TssiRefA   = Power.field.Byte0;
		pAd->TssiPlusBoundaryA[1] = Power.field.Byte1;
		RT28xx_EEPROM_READ16(pAd, 0xDA, Power.word);
		pAd->TssiPlusBoundaryA[2] = Power.field.Byte0;
		pAd->TssiPlusBoundaryA[3] = Power.field.Byte1;
		RT28xx_EEPROM_READ16(pAd, 0xDC, Power.word);
		pAd->TssiPlusBoundaryA[4] = Power.field.Byte0;
		pAd->TxAgcStepA = Power.field.Byte1;
		pAd->TxAgcCompensateA = 0;
		pAd->TssiMinusBoundaryA[0] = pAd->TssiRefA;
		pAd->TssiPlusBoundaryA[0]  = pAd->TssiRefA;

		// Disable TxAgc if the based value is not right
		if (pAd->TssiRefA == 0xff)
			pAd->bAutoTxAgcA = FALSE;

		DBGPRINT(RT_DEBUG_TRACE,("E2PROM: A Tssi[-4 .. +4] = %d %d %d %d - %d -%d %d %d %d, step=%d, tuning=%d\n",
			pAd->TssiMinusBoundaryA[4], pAd->TssiMinusBoundaryA[3], pAd->TssiMinusBoundaryA[2], pAd->TssiMinusBoundaryA[1],
			pAd->TssiRefA,
			pAd->TssiPlusBoundaryA[1], pAd->TssiPlusBoundaryA[2], pAd->TssiPlusBoundaryA[3], pAd->TssiPlusBoundaryA[4],
			pAd->TxAgcStepA, pAd->bAutoTxAgcA));
	}
	pAd->BbpRssiToDbmDelta = 0x0;

	// Read frequency offset setting for RF
	RT28xx_EEPROM_READ16(pAd, EEPROM_FREQ_OFFSET, value);
	if ((value & 0x00FF) != 0x00FF)
		pAd->RfFreqOffset = (ULONG) (value & 0x00FF);
	else
		pAd->RfFreqOffset = 0;
	DBGPRINT(RT_DEBUG_TRACE, ("E2PROM: RF FreqOffset=0x%lx \n", pAd->RfFreqOffset));

	//CountryRegion byte offset (38h)
	value = pAd->EEPROMDefaultValue[2] >> 8;		// 2.4G band
	value2 = pAd->EEPROMDefaultValue[2] & 0x00FF;	// 5G band

	if ((value <= REGION_MAXIMUM_BG_BAND) && (value2 <= REGION_MAXIMUM_A_BAND))
	{
		pAd->CommonCfg.CountryRegion = ((UCHAR) value) | 0x80;
		pAd->CommonCfg.CountryRegionForABand = ((UCHAR) value2) | 0x80;
		TmpPhy = pAd->CommonCfg.PhyMode;
		pAd->CommonCfg.PhyMode = 0xff;
		RTMPSetPhyMode(pAd, TmpPhy);
#ifdef DOT11_N_SUPPORT
		SetCommonHT(pAd);
#endif // DOT11_N_SUPPORT //
	}

	//
	// Get RSSI Offset on EEPROM 0x9Ah & 0x9Ch.
	// The valid value are (-10 ~ 10)
	//
	RT28xx_EEPROM_READ16(pAd, EEPROM_RSSI_BG_OFFSET, value);
	pAd->BGRssiOffset0 = value & 0x00ff;
	pAd->BGRssiOffset1 = (value >> 8);
	RT28xx_EEPROM_READ16(pAd, EEPROM_RSSI_BG_OFFSET+2, value);
	pAd->BGRssiOffset2 = value & 0x00ff;
	pAd->ALNAGain1 = (value >> 8);
	RT28xx_EEPROM_READ16(pAd, EEPROM_LNA_OFFSET, value);
	pAd->BLNAGain = value & 0x00ff;
	pAd->ALNAGain0 = (value >> 8);

	// Validate 11b/g RSSI_0 offset.
	if ((pAd->BGRssiOffset0 < -10) || (pAd->BGRssiOffset0 > 10))
		pAd->BGRssiOffset0 = 0;

	// Validate 11b/g RSSI_1 offset.
	if ((pAd->BGRssiOffset1 < -10) || (pAd->BGRssiOffset1 > 10))
		pAd->BGRssiOffset1 = 0;

	// Validate 11b/g RSSI_2 offset.
	if ((pAd->BGRssiOffset2 < -10) || (pAd->BGRssiOffset2 > 10))
		pAd->BGRssiOffset2 = 0;

	RT28xx_EEPROM_READ16(pAd, EEPROM_RSSI_A_OFFSET, value);
	pAd->ARssiOffset0 = value & 0x00ff;
	pAd->ARssiOffset1 = (value >> 8);
	RT28xx_EEPROM_READ16(pAd, (EEPROM_RSSI_A_OFFSET+2), value);
	pAd->ARssiOffset2 = value & 0x00ff;
	pAd->ALNAGain2 = (value >> 8);

	if (((UCHAR)pAd->ALNAGain1 == 0xFF) || (pAd->ALNAGain1 == 0x00))
		pAd->ALNAGain1 = pAd->ALNAGain0;
	if (((UCHAR)pAd->ALNAGain2 == 0xFF) || (pAd->ALNAGain2 == 0x00))
		pAd->ALNAGain2 = pAd->ALNAGain0;

	// Validate 11a RSSI_0 offset.
	if ((pAd->ARssiOffset0 < -10) || (pAd->ARssiOffset0 > 10))
		pAd->ARssiOffset0 = 0;

	// Validate 11a RSSI_1 offset.
	if ((pAd->ARssiOffset1 < -10) || (pAd->ARssiOffset1 > 10))
		pAd->ARssiOffset1 = 0;

	//Validate 11a RSSI_2 offset.
	if ((pAd->ARssiOffset2 < -10) || (pAd->ARssiOffset2 > 10))
		pAd->ARssiOffset2 = 0;

#ifdef RT30xx
	//
	// Get TX mixer gain setting
	// 0xff are invalid value
	// Note: RT30xX default value is 0x00 and will program to RF_R17 only when this value is not zero.
	//       RT359X default value is 0x02
	//
	if (IS_RT30xx(pAd) || IS_RT3572(pAd))
	{
		RT28xx_EEPROM_READ16(pAd, EEPROM_TXMIXER_GAIN_2_4G, value);
		pAd->TxMixerGain24G = 0;
		value &= 0x00ff;
		if (value != 0xff)
		{
			value &= 0x07;
			pAd->TxMixerGain24G = (UCHAR)value;
		}
	}
#endif // RT30xx //

	//
	// Get LED Setting.
	//
	RT28xx_EEPROM_READ16(pAd, 0x3a, value);
	pAd->LedCntl.word = (value>>8);
	RT28xx_EEPROM_READ16(pAd, EEPROM_LED1_OFFSET, value);
	pAd->Led1 = value;
	RT28xx_EEPROM_READ16(pAd, EEPROM_LED2_OFFSET, value);
	pAd->Led2 = value;
	RT28xx_EEPROM_READ16(pAd, EEPROM_LED3_OFFSET, value);
	pAd->Led3 = value;

	RTMPReadTxPwrPerRate(pAd);

#ifdef SINGLE_SKU
	RT28xx_EEPROM_READ16(pAd, EEPROM_DEFINE_MAX_TXPWR, pAd->CommonCfg.DefineMaxTxPwr);
#endif // SINGLE_SKU //

#ifdef RT30xx
#ifdef RTMP_EFUSE_SUPPORT
	RtmpEfuseSupportCheck(pAd);
#endif // RTMP_EFUSE_SUPPORT //
#endif // RT30xx //

	DBGPRINT(RT_DEBUG_TRACE, ("<-- NICReadEEPROMParameters\n"));
}


/*
	========================================================================

	Routine Description:
		Set default value from EEPROM

	Arguments:
		Adapter						Pointer to our adapter

	Return Value:
		None

	IRQL = PASSIVE_LEVEL

	Note:

	========================================================================
*/
VOID	NICInitAsicFromEEPROM(
	IN	PRTMP_ADAPTER	pAd)
{
#ifdef CONFIG_STA_SUPPORT
	UINT32					data = 0;
	UCHAR	BBPR1 = 0;
#endif // CONFIG_STA_SUPPORT //
	USHORT					i;
//	EEPROM_ANTENNA_STRUC	Antenna;
	EEPROM_NIC_CONFIG2_STRUC    NicConfig2;
	UCHAR	BBPR3 = 0;

	DBGPRINT(RT_DEBUG_TRACE, ("--> NICInitAsicFromEEPROM\n"));
	for(i = 3; i < NUM_EEPROM_BBP_PARMS; i++)
	{
		UCHAR BbpRegIdx, BbpValue;

		if ((pAd->EEPROMDefaultValue[i] != 0xFFFF) && (pAd->EEPROMDefaultValue[i] != 0))
		{
			BbpRegIdx = (UCHAR)(pAd->EEPROMDefaultValue[i] >> 8);
			BbpValue  = (UCHAR)(pAd->EEPROMDefaultValue[i] & 0xff);
			RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BbpRegIdx, BbpValue);
		}
	}


	NicConfig2.word = pAd->EEPROMDefaultValue[1];


#ifdef CONFIG_STA_SUPPORT
	IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
	{
		if ((NicConfig2.word & 0x00ff) == 0xff)
		{
			NicConfig2.word &= 0xff00;
		}

		if ((NicConfig2.word >> 8) == 0xff)
		{
			NicConfig2.word &= 0x00ff;
		}
	}
#endif // CONFIG_STA_SUPPORT //

	// Save the antenna for future use
	pAd->NicConfig2.word = NicConfig2.word;

#ifdef RT30xx
	// set default antenna as main
	if (pAd->RfIcType == RFIC_3020)
		AsicSetRxAnt(pAd, pAd->RxAnt.Pair1PrimaryRxAnt);
#endif // RT30xx //

	//
	// Send LED Setting to MCU.
	//
	if (pAd->LedCntl.word == 0xFF)
	{
		pAd->LedCntl.word = 0x01;
		pAd->Led1 = 0x5555;
		pAd->Led2 = 0x2221;

#ifdef RTMP_MAC_PCI
		pAd->Led3 = 0xA9F8;
#endif // RTMP_MAC_PCI //
	}

	AsicSendCommandToMcu(pAd, 0x52, 0xff, (UCHAR)pAd->Led1, (UCHAR)(pAd->Led1 >> 8));
	AsicSendCommandToMcu(pAd, 0x53, 0xff, (UCHAR)pAd->Led2, (UCHAR)(pAd->Led2 >> 8));
	AsicSendCommandToMcu(pAd, 0x54, 0xff, (UCHAR)pAd->Led3, (UCHAR)(pAd->Led3 >> 8));
	AsicSendCommandToMcu(pAd, 0x51, 0xff, 0, pAd->LedCntl.field.Polarity);

	pAd->LedIndicatorStrength = 0xFF;
	RTMPSetSignalLED(pAd, -100);	// Force signal strength Led to be turned off, before link up

#ifdef CONFIG_STA_SUPPORT
	IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
	{
		// Read Hardware controlled Radio state enable bit
		if (NicConfig2.field.HardwareRadioControl == 1)
		{
			pAd->StaCfg.bHardwareRadio = TRUE;

			// Read GPIO pin2 as Hardware controlled radio state
			RTMP_IO_READ32(pAd, GPIO_CTRL_CFG, &data);
			if ((data & 0x04) == 0)
			{
				pAd->StaCfg.bHwRadio = FALSE;
				pAd->StaCfg.bRadio = FALSE;
//				RTMP_IO_WRITE32(pAd, PWR_PIN_CFG, 0x00001818);
				RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_RADIO_OFF);
			}
		}
		else
			pAd->StaCfg.bHardwareRadio = FALSE;

		if (pAd->StaCfg.bRadio == FALSE)
		{
			RTMPSetLED(pAd, LED_RADIO_OFF);
		}
		else
		{
			RTMPSetLED(pAd, LED_RADIO_ON);
#ifdef RTMP_MAC_PCI
#ifdef RT3090
			AsicSendCommandToMcu(pAd, 0x30, PowerRadioOffCID, 0xff, 0x02);
			AsicCheckCommanOk(pAd, PowerRadioOffCID);
#endif // RT3090 //
#ifndef RT3090
			AsicSendCommandToMcu(pAd, 0x30, 0xff, 0xff, 0x02);
#endif // RT3090 //
			AsicSendCommandToMcu(pAd, 0x31, PowerWakeCID, 0x00, 0x00);
			// 2-1. wait command ok.
			AsicCheckCommanOk(pAd, PowerWakeCID);
#endif // RTMP_MAC_PCI //
		}
	}
#ifdef RTMP_MAC_PCI
#ifdef RT30xx
		if (IS_RT3090(pAd)|| IS_RT3572(pAd) || IS_RT3390(pAd))
		{
			RTMP_CHIP_OP *pChipOps = &pAd->chipOps;
			if (pChipOps->AsicReverseRfFromSleepMode)
				pChipOps->AsicReverseRfFromSleepMode(pAd);
		}
		// 3090 MCU Wakeup command needs more time to be stable.
		// Before stable, don't issue other MCU command to prevent from firmware error.

		if ((IS_RT3090(pAd)|| IS_RT3572(pAd) || IS_RT3390(pAd)) && IS_VERSION_AFTER_F(pAd)
			&& (pAd->StaCfg.PSControl.field.rt30xxPowerMode == 3)
			&& (pAd->StaCfg.PSControl.field.EnableNewPS == TRUE))
		{
			DBGPRINT(RT_DEBUG_TRACE,("%s::%d,release Mcu Lock\n",__FUNCTION__,__LINE__));
			RTMP_SEM_LOCK(&pAd->McuCmdLock);
			pAd->brt30xxBanMcuCmd = FALSE;
			RTMP_SEM_UNLOCK(&pAd->McuCmdLock);
		}
#endif // RT30xx //
#endif // RTMP_MAC_PCI //
#endif // CONFIG_STA_SUPPORT //

	// Turn off patching for cardbus controller
	if (NicConfig2.field.CardbusAcceleration == 1)
	{
//		pAd->bTest1 = TRUE;
	}

	if (NicConfig2.field.DynamicTxAgcControl == 1)
		pAd->bAutoTxAgcA = pAd->bAutoTxAgcG = TRUE;
	else
		pAd->bAutoTxAgcA = pAd->bAutoTxAgcG = FALSE;
	//
	// Since BBP has been progamed, to make sure BBP setting will be
	// upate inside of AsicAntennaSelect, so reset to UNKNOWN_BAND!!
	//
	pAd->CommonCfg.BandState = UNKNOWN_BAND;

	RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R3, &BBPR3);
	BBPR3 &= (~0x18);
	if(pAd->Antenna.field.RxPath == 3)
	{
		BBPR3 |= (0x10);
	}
	else if(pAd->Antenna.field.RxPath == 2)
	{
		BBPR3 |= (0x8);
	}
	else if(pAd->Antenna.field.RxPath == 1)
	{
		BBPR3 |= (0x0);
	}
	RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R3, BBPR3);

#ifdef CONFIG_STA_SUPPORT
	IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
	{
		// Handle the difference when 1T
		RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R1, &BBPR1);
		if(pAd->Antenna.field.TxPath == 1)
		{
		BBPR1 &= (~0x18);
		}
		RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R1, BBPR1);

		DBGPRINT(RT_DEBUG_TRACE, ("Use Hw Radio Control Pin=%d; if used Pin=%d;\n",
					pAd->CommonCfg.bHardwareRadio, pAd->CommonCfg.bHardwareRadio));
	}
#endif // CONFIG_STA_SUPPORT //


	DBGPRINT(RT_DEBUG_TRACE, ("TxPath = %d, RxPath = %d, RFIC=%d, Polar+LED mode=%x\n",
				pAd->Antenna.field.TxPath, pAd->Antenna.field.RxPath,
				pAd->RfIcType, pAd->LedCntl.word));
	DBGPRINT(RT_DEBUG_TRACE, ("<-- NICInitAsicFromEEPROM\n"));
}

/*
	========================================================================

	Routine Description:
		Initialize NIC hardware

	Arguments:
		Adapter						Pointer to our adapter

	Return Value:
		None

	IRQL = PASSIVE_LEVEL

	Note:

	========================================================================
*/
NDIS_STATUS	NICInitializeAdapter(
	IN	PRTMP_ADAPTER	pAd,
	IN   BOOLEAN    bHardReset)
{
	NDIS_STATUS     Status = NDIS_STATUS_SUCCESS;
	WPDMA_GLO_CFG_STRUC	GloCfg;
#ifdef RTMP_MAC_PCI
	UINT32			Value;
	DELAY_INT_CFG_STRUC	IntCfg;
#endif // RTMP_MAC_PCI //
//	INT_MASK_CSR_STRUC		IntMask;
	ULONG	i =0, j=0;
	AC_TXOP_CSR0_STRUC	csr0;

	DBGPRINT(RT_DEBUG_TRACE, ("--> NICInitializeAdapter\n"));

	// 3. Set DMA global configuration except TX_DMA_EN and RX_DMA_EN bits:
retry:
	i = 0;
	do
	{
		RTMP_IO_READ32(pAd, WPDMA_GLO_CFG, &GloCfg.word);
		if ((GloCfg.field.TxDMABusy == 0)  && (GloCfg.field.RxDMABusy == 0))
			break;

		RTMPusecDelay(1000);
		i++;
	}while ( i<100);
	DBGPRINT(RT_DEBUG_TRACE, ("<== DMA offset 0x208 = 0x%x\n", GloCfg.word));
	GloCfg.word &= 0xff0;
	GloCfg.field.EnTXWriteBackDDONE =1;
	RTMP_IO_WRITE32(pAd, WPDMA_GLO_CFG, GloCfg.word);

	// Record HW Beacon offset
	pAd->BeaconOffset[0] = HW_BEACON_BASE0;
	pAd->BeaconOffset[1] = HW_BEACON_BASE1;
	pAd->BeaconOffset[2] = HW_BEACON_BASE2;
	pAd->BeaconOffset[3] = HW_BEACON_BASE3;
	pAd->BeaconOffset[4] = HW_BEACON_BASE4;
	pAd->BeaconOffset[5] = HW_BEACON_BASE5;
	pAd->BeaconOffset[6] = HW_BEACON_BASE6;
	pAd->BeaconOffset[7] = HW_BEACON_BASE7;

	//
	// write all shared Ring's base address into ASIC
	//

	// asic simulation sequence put this ahead before loading firmware.
	// pbf hardware reset
#ifdef RTMP_MAC_PCI
	RTMP_IO_WRITE32(pAd, WPDMA_RST_IDX, 0x1003f);	// 0x10000 for reset rx, 0x3f resets all 6 tx rings.
	RTMP_IO_WRITE32(pAd, PBF_SYS_CTRL, 0xe1f);
	RTMP_IO_WRITE32(pAd, PBF_SYS_CTRL, 0xe00);
#endif // RTMP_MAC_PCI //

	// Initialze ASIC for TX & Rx operation
	if (NICInitializeAsic(pAd , bHardReset) != NDIS_STATUS_SUCCESS)
	{
		if (j++ == 0)
		{
			NICLoadFirmware(pAd);
			goto retry;
		}
		return NDIS_STATUS_FAILURE;
	}


#ifdef RTMP_MAC_PCI
	// Write AC_BK base address register
	Value = RTMP_GetPhysicalAddressLow(pAd->TxRing[QID_AC_BK].Cell[0].AllocPa);
	RTMP_IO_WRITE32(pAd, TX_BASE_PTR1, Value);
	DBGPRINT(RT_DEBUG_TRACE, ("--> TX_BASE_PTR1 : 0x%x\n", Value));

	// Write AC_BE base address register
	Value = RTMP_GetPhysicalAddressLow(pAd->TxRing[QID_AC_BE].Cell[0].AllocPa);
	RTMP_IO_WRITE32(pAd, TX_BASE_PTR0, Value);
	DBGPRINT(RT_DEBUG_TRACE, ("--> TX_BASE_PTR0 : 0x%x\n", Value));

	// Write AC_VI base address register
	Value = RTMP_GetPhysicalAddressLow(pAd->TxRing[QID_AC_VI].Cell[0].AllocPa);
	RTMP_IO_WRITE32(pAd, TX_BASE_PTR2, Value);
	DBGPRINT(RT_DEBUG_TRACE, ("--> TX_BASE_PTR2 : 0x%x\n", Value));

	// Write AC_VO base address register
	Value = RTMP_GetPhysicalAddressLow(pAd->TxRing[QID_AC_VO].Cell[0].AllocPa);
	RTMP_IO_WRITE32(pAd, TX_BASE_PTR3, Value);
	DBGPRINT(RT_DEBUG_TRACE, ("--> TX_BASE_PTR3 : 0x%x\n", Value));

	// Write HCCA base address register
	/*
	Value = RTMP_GetPhysicalAddressLow(pAd->TxRing[QID_HCCA].Cell[0].AllocPa);
	RTMP_IO_WRITE32(pAd, TX_BASE_PTR4, Value);
	DBGPRINT(RT_DEBUG_TRACE, ("--> TX_BASE_PTR4 : 0x%x\n", Value));
	*/

	// Write MGMT_BASE_CSR register
	Value = RTMP_GetPhysicalAddressLow(pAd->MgmtRing.Cell[0].AllocPa);
	RTMP_IO_WRITE32(pAd, TX_BASE_PTR5, Value);
	DBGPRINT(RT_DEBUG_TRACE, ("--> TX_BASE_PTR5 : 0x%x\n", Value));

	// Write RX_BASE_CSR register
	Value = RTMP_GetPhysicalAddressLow(pAd->RxRing.Cell[0].AllocPa);
	RTMP_IO_WRITE32(pAd, RX_BASE_PTR, Value);
	DBGPRINT(RT_DEBUG_TRACE, ("--> RX_BASE_PTR : 0x%x\n", Value));

	// Init RX Ring index pointer
	pAd->RxRing.RxSwReadIdx = 0;
	pAd->RxRing.RxCpuIdx = RX_RING_SIZE-1;
	RTMP_IO_WRITE32(pAd, RX_CRX_IDX, pAd->RxRing.RxCpuIdx);

	// Init TX rings index pointer
	{
		for (i=0; i<NUM_OF_TX_RING; i++)
		{
			pAd->TxRing[i].TxSwFreeIdx = 0;
			pAd->TxRing[i].TxCpuIdx = 0;
			RTMP_IO_WRITE32(pAd, (TX_CTX_IDX0 + i * 0x10) ,  pAd->TxRing[i].TxCpuIdx);
		}
	}

	// init MGMT ring index pointer
	pAd->MgmtRing.TxSwFreeIdx = 0;
	pAd->MgmtRing.TxCpuIdx = 0;
	RTMP_IO_WRITE32(pAd, TX_MGMTCTX_IDX,  pAd->MgmtRing.TxCpuIdx);

	//
	// set each Ring's SIZE  into ASIC. Descriptor Size is fixed by design.
	//

	// Write TX_RING_CSR0 register
	Value = TX_RING_SIZE;
	RTMP_IO_WRITE32(pAd, TX_MAX_CNT0, Value);
	RTMP_IO_WRITE32(pAd, TX_MAX_CNT1, Value);
	RTMP_IO_WRITE32(pAd, TX_MAX_CNT2, Value);
	RTMP_IO_WRITE32(pAd, TX_MAX_CNT3, Value);
	RTMP_IO_WRITE32(pAd, TX_MAX_CNT4, Value);
	Value = MGMT_RING_SIZE;
	RTMP_IO_WRITE32(pAd, TX_MGMTMAX_CNT, Value);

	// Write RX_RING_CSR register
	Value = RX_RING_SIZE;
	RTMP_IO_WRITE32(pAd, RX_MAX_CNT, Value);
#endif // RTMP_MAC_PCI //


	// WMM parameter
	csr0.word = 0;
	RTMP_IO_WRITE32(pAd, WMM_TXOP0_CFG, csr0.word);
	if (pAd->CommonCfg.PhyMode == PHY_11B)
	{
		csr0.field.Ac0Txop = 192;	// AC_VI: 192*32us ~= 6ms
		csr0.field.Ac1Txop = 96;	// AC_VO: 96*32us  ~= 3ms
	}
	else
	{
		csr0.field.Ac0Txop = 96;	// AC_VI: 96*32us ~= 3ms
		csr0.field.Ac1Txop = 48;	// AC_VO: 48*32us ~= 1.5ms
	}
	RTMP_IO_WRITE32(pAd, WMM_TXOP1_CFG, csr0.word);


#ifdef RTMP_MAC_PCI
	// 3. Set DMA global configuration except TX_DMA_EN and RX_DMA_EN bits:
	i = 0;
	do
	{
		RTMP_IO_READ32(pAd, WPDMA_GLO_CFG, &GloCfg.word);
		if ((GloCfg.field.TxDMABusy == 0)  && (GloCfg.field.RxDMABusy == 0))
			break;

		RTMPusecDelay(1000);
		i++;
	}while ( i < 100);

	GloCfg.word &= 0xff0;
	GloCfg.field.EnTXWriteBackDDONE =1;
	RTMP_IO_WRITE32(pAd, WPDMA_GLO_CFG, GloCfg.word);

	IntCfg.word = 0;
	RTMP_IO_WRITE32(pAd, DELAY_INT_CFG, IntCfg.word);
#endif // RTMP_MAC_PCI //


	// reset action
	// Load firmware
	//  Status = NICLoadFirmware(pAd);

	DBGPRINT(RT_DEBUG_TRACE, ("<-- NICInitializeAdapter\n"));
	return Status;
}

/*
	========================================================================

	Routine Description:
		Initialize ASIC

	Arguments:
		Adapter						Pointer to our adapter

	Return Value:
		None

	IRQL = PASSIVE_LEVEL

	Note:

	========================================================================
*/
NDIS_STATUS	NICInitializeAsic(
	IN	PRTMP_ADAPTER	pAd,
	IN  BOOLEAN		bHardReset)
{
	ULONG			Index = 0;
	UCHAR			R0 = 0xff;
	UINT32			MacCsr12 = 0, Counter = 0;
#ifdef RT30xx
	UCHAR			bbpreg=0;
	UCHAR			RFValue=0;
#endif // RT30xx //
	USHORT			KeyIdx;
	INT				i,apidx;

	DBGPRINT(RT_DEBUG_TRACE, ("--> NICInitializeAsic\n"));

#ifdef RTMP_MAC_PCI
	RTMP_IO_WRITE32(pAd, PWR_PIN_CFG, 0x3);	// To fix driver disable/enable hang issue when radio off
	if (bHardReset == TRUE)
	{
		RTMP_IO_WRITE32(pAd, MAC_SYS_CTRL, 0x3);
	}
	else
		RTMP_IO_WRITE32(pAd, MAC_SYS_CTRL, 0x1);

	RTMP_IO_WRITE32(pAd, MAC_SYS_CTRL, 0x0);
	// Initialize MAC register to default value
	for (Index = 0; Index < NUM_MAC_REG_PARMS; Index++)
	{
#ifdef RT30xx
		if ((MACRegTable[Index].Register == TX_SW_CFG0) && ( IS_RT3090(pAd) ||  IS_RT3390(pAd)))
		{
			MACRegTable[Index].Value = 0x00000400;
		}
#endif // RT30xx //
		RTMP_IO_WRITE32(pAd, MACRegTable[Index].Register, MACRegTable[Index].Value);
	}


#ifdef CONFIG_STA_SUPPORT
	IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
	{
		for (Index = 0; Index < NUM_STA_MAC_REG_PARMS; Index++)
		{
			RTMP_IO_WRITE32(pAd, STAMACRegTable[Index].Register, STAMACRegTable[Index].Value);
		}
	}
#endif // CONFIG_STA_SUPPORT //
#endif // RTMP_MAC_PCI //


#ifdef RT30xx
	// Initialize RT3070 serial MAC registers which is different from RT2870 serial
	if (IS_RT3090(pAd) || IS_RT3572(pAd)||IS_RT3390(pAd))
	{
		RTMP_IO_WRITE32(pAd, TX_SW_CFG1, 0);

		// RT3071 version E has fixed this issue
		if ((pAd->MACVersion & 0xffff) < 0x0211)
		{
			if (pAd->NicConfig2.field.DACTestBit == 1)
			{
				RTMP_IO_WRITE32(pAd, TX_SW_CFG2, 0x2C);	// To fix throughput drop drastically
			}
			else
			{
				RTMP_IO_WRITE32(pAd, TX_SW_CFG2, 0x0F);	// To fix throughput drop drastically
			}
		}
		else
		{
			RTMP_IO_WRITE32(pAd, TX_SW_CFG2, 0x0);
		}
	}
	else if (IS_RT3070(pAd))
	{
		if (((pAd->MACVersion & 0xffff) < 0x0201))
		{
			RTMP_IO_WRITE32(pAd, TX_SW_CFG1, 0);
			RTMP_IO_WRITE32(pAd, TX_SW_CFG2, 0x2C);	// To fix throughput drop drastically
		}
		else
		{
			RTMP_IO_WRITE32(pAd, TX_SW_CFG2, 0);
		}
	}
#endif // RT30xx //

	//
	// Before program BBP, we need to wait BBP/RF get wake up.
	//
	Index = 0;
	do
	{
		RTMP_IO_READ32(pAd, MAC_STATUS_CFG, &MacCsr12);

		if ((MacCsr12 & 0x03) == 0)	// if BB.RF is stable
			break;

		DBGPRINT(RT_DEBUG_TRACE, ("Check MAC_STATUS_CFG  = Busy = %x\n", MacCsr12));
		RTMPusecDelay(1000);
	} while (Index++ < 100);

	// The commands to firmware should be after these commands, these commands will init firmware
	// PCI and USB are not the same because PCI driver needs to wait for PCI bus ready
	RTMP_IO_WRITE32(pAd, H2M_BBP_AGENT, 0);	// initialize BBP R/W access agent
	RTMP_IO_WRITE32(pAd, H2M_MAILBOX_CSR, 0);
#ifdef RT3090
	//2008/11/28:KH add to fix the dead rf frequency offset bug<--
	AsicSendCommandToMcu(pAd, 0x72, 0, 0, 0);
	//2008/11/28:KH add to fix the dead rf frequency offset bug-->
#endif // RT3090 //
	RTMPusecDelay(1000);

	// Read BBP register, make sure BBP is up and running before write new data
	Index = 0;
	do
	{
		RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R0, &R0);
		DBGPRINT(RT_DEBUG_TRACE, ("BBP version = %x\n", R0));
	} while ((++Index < 20) && ((R0 == 0xff) || (R0 == 0x00)));
	//ASSERT(Index < 20); //this will cause BSOD on Check-build driver

	if ((R0 == 0xff) || (R0 == 0x00))
		return NDIS_STATUS_FAILURE;

	// Initialize BBP register to default value
	for (Index = 0; Index < NUM_BBP_REG_PARMS; Index++)
	{
		RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBPRegTable[Index].Register, BBPRegTable[Index].Value);
	}

#ifdef RTMP_MAC_PCI
	// TODO: shiang, check MACVersion, currently, rbus-based chip use this.
	if (pAd->MACVersion == 0x28720200)
	{
		//UCHAR value;
		ULONG value2;

		//disable MLD by Bruce 20080704
		//BBP_IO_READ8_BY_REG_ID(pAd, BBP_R105, &value);
		//BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R105, value | 4);

		//Maximum PSDU length from 16K to 32K bytes
		RTMP_IO_READ32(pAd, MAX_LEN_CFG, &value2);
		value2 &= ~(0x3<<12);
		value2 |= (0x2<<12);
		RTMP_IO_WRITE32(pAd, MAX_LEN_CFG, value2);
	}
#endif // RTMP_MAC_PCI //

	// for rt2860E and after, init BBP_R84 with 0x19. This is for extension channel overlapping IOT.
	// RT3090 should not program BBP R84 to 0x19, otherwise TX will block.
	//3070/71/72,3090,3090A( are included in RT30xx),3572,3390
	if (((pAd->MACVersion & 0xffff) != 0x0101) && !(IS_RT30xx(pAd)|| IS_RT3572(pAd) || IS_RT3390(pAd)))
		RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R84, 0x19);

#ifdef RT30xx
// add by johnli, RF power sequence setup
	if (IS_RT30xx(pAd) || IS_RT3572(pAd) || IS_RT3390(pAd))
	{	//update for RT3070/71/72/90/91/92,3572,3390.
		RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R79, 0x13);
		RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R80, 0x05);
		RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R81, 0x33);
	}

	if (IS_RT3090(pAd)||IS_RT3390(pAd))	// RT309x, RT3071/72
	{
		// enable DC filter
		if ((pAd->MACVersion & 0xffff) >= 0x0211)
		{
			RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R103, 0xc0);
		}

		// improve power consumption
		RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R138, &bbpreg);
		if (pAd->Antenna.field.TxPath == 1)
		{
			// turn off tx DAC_1
			bbpreg = (bbpreg | 0x20);
		}

		if (pAd->Antenna.field.RxPath == 1)
		{
			// turn off tx ADC_1
			bbpreg &= (~0x2);
		}
		RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R138, bbpreg);

		// improve power consumption in RT3071 Ver.E
		if ((pAd->MACVersion & 0xffff) >= 0x0211)
		{
			RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R31, &bbpreg);
			bbpreg &= (~0x3);
			RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R31, bbpreg);
		}
	}
	else if (IS_RT3070(pAd))
	{
		if ((pAd->MACVersion & 0xffff) >= 0x0201)
		{
			// enable DC filter
			RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R103, 0xc0);

			// improve power consumption in RT3070 Ver.F
			RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R31, &bbpreg);
			bbpreg &= (~0x3);
			RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R31, bbpreg);
		}

		// TX_LO1_en, RF R17 register Bit 3 to 0
		RT30xxReadRFRegister(pAd, RF_R17, &RFValue);
		RFValue &= (~0x08);
		// to fix rx long range issue
		if (pAd->NicConfig2.field.ExternalLNAForG == 0)
		{
			RFValue |= 0x20;
		}
		// set RF_R17_bit[2:0] equal to EEPROM setting at 0x48h
		if (pAd->TxMixerGain24G >= 1)
		{
			RFValue &= (~0x7);  // clean bit [2:0]
			RFValue |= pAd->TxMixerGain24G;
		}
		RT30xxWriteRFRegister(pAd, RF_R17, RFValue);
	}
// end johnli
#endif // RT30xx //

	if (pAd->MACVersion == 0x28600100)
	{
		RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R69, 0x16);
		RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R73, 0x12);
	}

	if (pAd->MACVersion >= RALINK_2880E_VERSION && pAd->MACVersion < RALINK_3070_VERSION) // 3*3
	{
		// enlarge MAX_LEN_CFG
		UINT32 csr;
		RTMP_IO_READ32(pAd, MAX_LEN_CFG, &csr);
		csr &= 0xFFF;
		csr |= 0x2000;
		RTMP_IO_WRITE32(pAd, MAX_LEN_CFG, csr);
	}


#ifdef CONFIG_STA_SUPPORT
	// Add radio off control
	IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
	{
		if (pAd->StaCfg.bRadio == FALSE)
		{
//			RTMP_IO_WRITE32(pAd, PWR_PIN_CFG, 0x00001818);
			RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_RADIO_OFF);
			DBGPRINT(RT_DEBUG_TRACE, ("Set Radio Off\n"));
		}
	}
#endif // CONFIG_STA_SUPPORT //

	// Clear raw counters
	RTMP_IO_READ32(pAd, RX_STA_CNT0, &Counter);
	RTMP_IO_READ32(pAd, RX_STA_CNT1, &Counter);
	RTMP_IO_READ32(pAd, RX_STA_CNT2, &Counter);
	RTMP_IO_READ32(pAd, TX_STA_CNT0, &Counter);
	RTMP_IO_READ32(pAd, TX_STA_CNT1, &Counter);
	RTMP_IO_READ32(pAd, TX_STA_CNT2, &Counter);

	// ASIC will keep garbage value after boot
	// Clear all shared key table when initial
	// This routine can be ignored in radio-ON/OFF operation.
	if (bHardReset)
	{
		for (KeyIdx = 0; KeyIdx < 4; KeyIdx++)
		{
			RTMP_IO_WRITE32(pAd, SHARED_KEY_MODE_BASE + 4*KeyIdx, 0);
		}

		// Clear all pairwise key table when initial
		for (KeyIdx = 0; KeyIdx < 256; KeyIdx++)
		{
			RTMP_IO_WRITE32(pAd, MAC_WCID_ATTRIBUTE_BASE + (KeyIdx * HW_WCID_ATTRI_SIZE), 1);
		}
	}

	// assert HOST ready bit
//  RTMP_IO_WRITE32(pAd, MAC_CSR1, 0x0); // 2004-09-14 asked by Mark
//  RTMP_IO_WRITE32(pAd, MAC_CSR1, 0x4);

	// It isn't necessary to clear this space when not hard reset.
	if (bHardReset == TRUE)
	{
		// clear all on-chip BEACON frame space
		for (apidx = 0; apidx < HW_BEACON_MAX_COUNT; apidx++)
		{
			for (i = 0; i < HW_BEACON_OFFSET>>2; i+=4)
				RTMP_IO_WRITE32(pAd, pAd->BeaconOffset[apidx] + i, 0x00);
		}
	}


#ifdef CONFIG_STA_SUPPORT
	IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
	{
		// for rt2860E and after, init TXOP_CTRL_CFG with 0x583f. This is for extension channel overlapping IOT.
		if ((pAd->MACVersion&0xffff) != 0x0101)
			RTMP_IO_WRITE32(pAd, TXOP_CTRL_CFG, 0x583f);
	}
#endif // CONFIG_STA_SUPPORT //

#ifdef RT30xx
#ifdef NEW_FW
	if (IS_RT3070(pAd) ||  IS_RT3572(pAd)||IS_RT3390(pAd)||IS_RT3090(pAd))
	{
		// send 0x36 mcu command after 0x72 for RT3xxx to fix Radio-Off current leakage issue
		RTMPusecDelay(200);
		if (pAd->buseEfuse)
			AsicSendCommandToMcu(pAd, 0x36, 0xff, 0xff, 0);
		else
			AsicSendCommandToMcu(pAd, 0x36, 0xff, 0xff, 0x04);
		RTMPusecDelay(10);
	}
#endif // NEW_FW //
#endif // RT30xx //

	DBGPRINT(RT_DEBUG_TRACE, ("<-- NICInitializeAsic\n"));
	return NDIS_STATUS_SUCCESS;
}

/*
	========================================================================

	Routine Description:
		Reset NIC Asics

	Arguments:
		Adapter						Pointer to our adapter

	Return Value:
		None

	IRQL = PASSIVE_LEVEL

	Note:
		Reset NIC to initial state AS IS system boot up time.

	========================================================================
*/
VOID	NICIssueReset(
	IN	PRTMP_ADAPTER	pAd)
{
	UINT32	Value = 0;
	DBGPRINT(RT_DEBUG_TRACE, ("--> NICIssueReset\n"));

	// Abort Tx, prevent ASIC from writing to Host memory
	//RTMP_IO_WRITE32(pAd, TX_CNTL_CSR, 0x001f0000);

	// Disable Rx, register value supposed will remain after reset
	RTMP_IO_READ32(pAd, MAC_SYS_CTRL, &Value);
	Value &= (0xfffffff3);
	RTMP_IO_WRITE32(pAd, MAC_SYS_CTRL, Value);

	// Issue reset and clear from reset state
	RTMP_IO_WRITE32(pAd, MAC_SYS_CTRL, 0x03); // 2004-09-17 change from 0x01
	RTMP_IO_WRITE32(pAd, MAC_SYS_CTRL, 0x00);

	DBGPRINT(RT_DEBUG_TRACE, ("<-- NICIssueReset\n"));
}

/*
	========================================================================

	Routine Description:
		Check ASIC registers and find any reason the system might hang

	Arguments:
		Adapter						Pointer to our adapter

	Return Value:
		None

	IRQL = DISPATCH_LEVEL

	========================================================================
*/
BOOLEAN	NICCheckForHang(
	IN	PRTMP_ADAPTER	pAd)
{
	return (FALSE);
}

VOID NICUpdateFifoStaCounters(
	IN PRTMP_ADAPTER pAd)
{
	TX_STA_FIFO_STRUC	StaFifo;
	MAC_TABLE_ENTRY		*pEntry;
	UCHAR				i = 0;
	UCHAR			pid = 0, wcid = 0;
	CHAR				reTry;
	UCHAR				succMCS;

#ifdef RALINK_ATE
	/* Nothing to do in ATE mode */
	if (ATE_ON(pAd))
		return;
#endif // RALINK_ATE //

		do
		{
			RTMP_IO_READ32(pAd, TX_STA_FIFO, &StaFifo.word);

			if (StaFifo.field.bValid == 0)
				break;

			wcid = (UCHAR)StaFifo.field.wcid;


		/* ignore NoACK and MGMT frame use 0xFF as WCID */
			if ((StaFifo.field.TxAckRequired == 0) || (wcid >= MAX_LEN_OF_MAC_TABLE))
			{
				i++;
				continue;
			}

			/* PID store Tx MCS Rate */
			pid = (UCHAR)StaFifo.field.PidType;

			pEntry = &pAd->MacTab.Content[wcid];

			pEntry->DebugFIFOCount++;

#ifdef DOT11_N_SUPPORT
			if (StaFifo.field.TxBF) // 3*3
				pEntry->TxBFCount++;
#endif // DOT11_N_SUPPORT //

#ifdef UAPSD_AP_SUPPORT
			UAPSD_SP_AUE_Handle(pAd, pEntry, StaFifo.field.TxSuccess);
#endif // UAPSD_AP_SUPPORT //

			if (!StaFifo.field.TxSuccess)
			{
				pEntry->FIFOCount++;
				pEntry->OneSecTxFailCount++;

				if (pEntry->FIFOCount >= 1)
				{
					DBGPRINT(RT_DEBUG_TRACE, ("#"));
#ifdef DOT11_N_SUPPORT
					pEntry->NoBADataCountDown = 64;
#endif // DOT11_N_SUPPORT //

					if(pEntry->PsMode == PWR_ACTIVE)
					{
#ifdef DOT11_N_SUPPORT
						int tid;
						for (tid=0; tid<NUM_OF_TID; tid++)
						{
							BAOriSessionTearDown(pAd, pEntry->Aid,  tid, FALSE, FALSE);
						}
#endif // DOT11_N_SUPPORT //

						// Update the continuous transmission counter except PS mode
						pEntry->ContinueTxFailCnt++;

#ifdef WDS_SUPPORT
						// fix WDS Jam issue
						if((pEntry->ValidAsWDS == TRUE)
							&& (pEntry->LockEntryTx == FALSE)
							&& (pEntry->ContinueTxFailCnt >= pAd->ApCfg.EntryLifeCheck))
						{
							DBGPRINT(RT_DEBUG_TRACE, ("Entry %02x:%02x:%02x:%02x:%02x:%02x Blocked!! (Fail Cnt = %d)\n",
								pEntry->Addr[0],pEntry->Addr[1],pEntry->Addr[2],pEntry->Addr[3],
								pEntry->Addr[4],pEntry->Addr[5],pEntry->ContinueTxFailCnt ));

							pEntry->LockEntryTx = TRUE;
						}
#endif // WDS_SUPPORT //
					}
					else
					{
						// Clear the FIFOCount when sta in Power Save mode. Basically we assume
						//     this tx error happened due to sta just go to sleep.
						pEntry->FIFOCount = 0;
						pEntry->ContinueTxFailCnt = 0;
					}
					//pEntry->FIFOCount = 0;
				}
				//pEntry->bSendBAR = TRUE;
			}
			else
			{
#ifdef DOT11_N_SUPPORT
				if ((pEntry->PsMode != PWR_SAVE) && (pEntry->NoBADataCountDown > 0))
				{
					pEntry->NoBADataCountDown--;
					if (pEntry->NoBADataCountDown==0)
					{
						DBGPRINT(RT_DEBUG_TRACE, ("@\n"));
					}
				}
#endif // DOT11_N_SUPPORT //
				pEntry->FIFOCount = 0;
				pEntry->OneSecTxNoRetryOkCount++;
				// update NoDataIdleCount when sucessful send packet to STA.
				pEntry->NoDataIdleCount = 0;
				pEntry->ContinueTxFailCnt = 0;
#ifdef WDS_SUPPORT
				pEntry->LockEntryTx = FALSE;
#endif // WDS_SUPPORT //
			}

			succMCS = StaFifo.field.SuccessRate & 0x7F;

			reTry = pid - succMCS;

			if (StaFifo.field.TxSuccess)
			{
				pEntry->TXMCSExpected[pid]++;
				if (pid == succMCS)
				{
					pEntry->TXMCSSuccessful[pid]++;
				}
				else
				{
					pEntry->TXMCSAutoFallBack[pid][succMCS]++;
				}
			}
			else
			{
				pEntry->TXMCSFailed[pid]++;
			}

			if (reTry > 0)
			{
				if ((pid >= 12) && succMCS <=7)
				{
					reTry -= 4;
				}
				pEntry->OneSecTxRetryOkCount += reTry;
			}

			i++;
			// ASIC store 16 stack
		} while ( i < (TX_RING_SIZE<<1) );

}

/*
	========================================================================

	Routine Description:
		Read statistical counters from hardware registers and record them
		in software variables for later on query

	Arguments:
		pAd					Pointer to our adapter

	Return Value:
		None

	IRQL = DISPATCH_LEVEL

	========================================================================
*/
VOID NICUpdateRawCounters(
	IN PRTMP_ADAPTER pAd)
{
	UINT32	OldValue;//, Value2;
	//ULONG	PageSum, OneSecTransmitCount;
	//ULONG	TxErrorRatio, Retry, Fail;
	RX_STA_CNT0_STRUC	 RxStaCnt0;
	RX_STA_CNT1_STRUC   RxStaCnt1;
	RX_STA_CNT2_STRUC   RxStaCnt2;
	TX_STA_CNT0_STRUC	 TxStaCnt0;
	TX_STA_CNT1_STRUC	 StaTx1;
	TX_STA_CNT2_STRUC	 StaTx2;
	TX_AGG_CNT_STRUC	TxAggCnt;
	TX_AGG_CNT0_STRUC	TxAggCnt0;
	TX_AGG_CNT1_STRUC	TxAggCnt1;
	TX_AGG_CNT2_STRUC	TxAggCnt2;
	TX_AGG_CNT3_STRUC	TxAggCnt3;
	TX_AGG_CNT4_STRUC	TxAggCnt4;
	TX_AGG_CNT5_STRUC	TxAggCnt5;
	TX_AGG_CNT6_STRUC	TxAggCnt6;
	TX_AGG_CNT7_STRUC	TxAggCnt7;
	COUNTER_RALINK		*pRalinkCounters;


	pRalinkCounters = &pAd->RalinkCounters;

	RTMP_IO_READ32(pAd, RX_STA_CNT0, &RxStaCnt0.word);
	RTMP_IO_READ32(pAd, RX_STA_CNT2, &RxStaCnt2.word);

	{
		RTMP_IO_READ32(pAd, RX_STA_CNT1, &RxStaCnt1.word);
	    // Update RX PLCP error counter
	    pAd->PrivateInfo.PhyRxErrCnt += RxStaCnt1.field.PlcpErr;
		// Update False CCA counter
		pAd->RalinkCounters.OneSecFalseCCACnt += RxStaCnt1.field.FalseCca;
	}

	// Update FCS counters
	OldValue= pAd->WlanCounters.FCSErrorCount.u.LowPart;
	pAd->WlanCounters.FCSErrorCount.u.LowPart += (RxStaCnt0.field.CrcErr); // >> 7);
	if (pAd->WlanCounters.FCSErrorCount.u.LowPart < OldValue)
		pAd->WlanCounters.FCSErrorCount.u.HighPart++;

	// Add FCS error count to private counters
	pRalinkCounters->OneSecRxFcsErrCnt += RxStaCnt0.field.CrcErr;
	OldValue = pRalinkCounters->RealFcsErrCount.u.LowPart;
	pRalinkCounters->RealFcsErrCount.u.LowPart += RxStaCnt0.field.CrcErr;
	if (pRalinkCounters->RealFcsErrCount.u.LowPart < OldValue)
		pRalinkCounters->RealFcsErrCount.u.HighPart++;

	// Update Duplicate Rcv check
	pRalinkCounters->DuplicateRcv += RxStaCnt2.field.RxDupliCount;
	pAd->WlanCounters.FrameDuplicateCount.u.LowPart += RxStaCnt2.field.RxDupliCount;
	// Update RX Overflow counter
	pAd->Counters8023.RxNoBuffer += (RxStaCnt2.field.RxFifoOverflowCount);

	//pAd->RalinkCounters.RxCount = 0;


	//if (!OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_TX_RATE_SWITCH_ENABLED) ||
	//	(OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_TX_RATE_SWITCH_ENABLED) && (pAd->MacTab.Size != 1)))
	if (!pAd->bUpdateBcnCntDone)
	{
	// Update BEACON sent count
	RTMP_IO_READ32(pAd, TX_STA_CNT0, &TxStaCnt0.word);
	RTMP_IO_READ32(pAd, TX_STA_CNT1, &StaTx1.word);
	RTMP_IO_READ32(pAd, TX_STA_CNT2, &StaTx2.word);
	pRalinkCounters->OneSecBeaconSentCnt += TxStaCnt0.field.TxBeaconCount;
	pRalinkCounters->OneSecTxRetryOkCount += StaTx1.field.TxRetransmit;
	pRalinkCounters->OneSecTxNoRetryOkCount += StaTx1.field.TxSuccess;
	pRalinkCounters->OneSecTxFailCount += TxStaCnt0.field.TxFailCount;
	pAd->WlanCounters.TransmittedFragmentCount.u.LowPart += StaTx1.field.TxSuccess;
	pAd->WlanCounters.RetryCount.u.LowPart += StaTx1.field.TxRetransmit;
	pAd->WlanCounters.FailedCount.u.LowPart += TxStaCnt0.field.TxFailCount;
	}


	//if (pAd->bStaFifoTest == TRUE)
	{
		RTMP_IO_READ32(pAd, TX_AGG_CNT, &TxAggCnt.word);
	RTMP_IO_READ32(pAd, TX_AGG_CNT0, &TxAggCnt0.word);
	RTMP_IO_READ32(pAd, TX_AGG_CNT1, &TxAggCnt1.word);
	RTMP_IO_READ32(pAd, TX_AGG_CNT2, &TxAggCnt2.word);
	RTMP_IO_READ32(pAd, TX_AGG_CNT3, &TxAggCnt3.word);
		RTMP_IO_READ32(pAd, TX_AGG_CNT4, &TxAggCnt4.word);
		RTMP_IO_READ32(pAd, TX_AGG_CNT5, &TxAggCnt5.word);
		RTMP_IO_READ32(pAd, TX_AGG_CNT6, &TxAggCnt6.word);
		RTMP_IO_READ32(pAd, TX_AGG_CNT7, &TxAggCnt7.word);
		pRalinkCounters->TxAggCount += TxAggCnt.field.AggTxCount;
		pRalinkCounters->TxNonAggCount += TxAggCnt.field.NonAggTxCount;
		pRalinkCounters->TxAgg1MPDUCount += TxAggCnt0.field.AggSize1Count;
		pRalinkCounters->TxAgg2MPDUCount += TxAggCnt0.field.AggSize2Count;

		pRalinkCounters->TxAgg3MPDUCount += TxAggCnt1.field.AggSize3Count;
		pRalinkCounters->TxAgg4MPDUCount += TxAggCnt1.field.AggSize4Count;
		pRalinkCounters->TxAgg5MPDUCount += TxAggCnt2.field.AggSize5Count;
		pRalinkCounters->TxAgg6MPDUCount += TxAggCnt2.field.AggSize6Count;

		pRalinkCounters->TxAgg7MPDUCount += TxAggCnt3.field.AggSize7Count;
		pRalinkCounters->TxAgg8MPDUCount += TxAggCnt3.field.AggSize8Count;
		pRalinkCounters->TxAgg9MPDUCount += TxAggCnt4.field.AggSize9Count;
		pRalinkCounters->TxAgg10MPDUCount += TxAggCnt4.field.AggSize10Count;

		pRalinkCounters->TxAgg11MPDUCount += TxAggCnt5.field.AggSize11Count;
		pRalinkCounters->TxAgg12MPDUCount += TxAggCnt5.field.AggSize12Count;
		pRalinkCounters->TxAgg13MPDUCount += TxAggCnt6.field.AggSize13Count;
		pRalinkCounters->TxAgg14MPDUCount += TxAggCnt6.field.AggSize14Count;

		pRalinkCounters->TxAgg15MPDUCount += TxAggCnt7.field.AggSize15Count;
		pRalinkCounters->TxAgg16MPDUCount += TxAggCnt7.field.AggSize16Count;

		// Calculate the transmitted A-MPDU count
		pRalinkCounters->TransmittedAMPDUCount.u.LowPart += TxAggCnt0.field.AggSize1Count;
		pRalinkCounters->TransmittedAMPDUCount.u.LowPart += (TxAggCnt0.field.AggSize2Count / 2);

		pRalinkCounters->TransmittedAMPDUCount.u.LowPart += (TxAggCnt1.field.AggSize3Count / 3);
		pRalinkCounters->TransmittedAMPDUCount.u.LowPart += (TxAggCnt1.field.AggSize4Count / 4);

		pRalinkCounters->TransmittedAMPDUCount.u.LowPart += (TxAggCnt2.field.AggSize5Count / 5);
		pRalinkCounters->TransmittedAMPDUCount.u.LowPart += (TxAggCnt2.field.AggSize6Count / 6);

		pRalinkCounters->TransmittedAMPDUCount.u.LowPart += (TxAggCnt3.field.AggSize7Count / 7);
		pRalinkCounters->TransmittedAMPDUCount.u.LowPart += (TxAggCnt3.field.AggSize8Count / 8);

		pRalinkCounters->TransmittedAMPDUCount.u.LowPart += (TxAggCnt4.field.AggSize9Count / 9);
		pRalinkCounters->TransmittedAMPDUCount.u.LowPart += (TxAggCnt4.field.AggSize10Count / 10);

		pRalinkCounters->TransmittedAMPDUCount.u.LowPart += (TxAggCnt5.field.AggSize11Count / 11);
		pRalinkCounters->TransmittedAMPDUCount.u.LowPart += (TxAggCnt5.field.AggSize12Count / 12);

		pRalinkCounters->TransmittedAMPDUCount.u.LowPart += (TxAggCnt6.field.AggSize13Count / 13);
		pRalinkCounters->TransmittedAMPDUCount.u.LowPart += (TxAggCnt6.field.AggSize14Count / 14);

		pRalinkCounters->TransmittedAMPDUCount.u.LowPart += (TxAggCnt7.field.AggSize15Count / 15);
		pRalinkCounters->TransmittedAMPDUCount.u.LowPart += (TxAggCnt7.field.AggSize16Count / 16);
	}

#ifdef DBG_DIAGNOSE
	{
		RtmpDiagStruct	*pDiag;
		UCHAR			ArrayCurIdx, i;

		pDiag = &pAd->DiagStruct;
		ArrayCurIdx = pDiag->ArrayCurIdx;

		if (pDiag->inited == 0)
		{
			NdisZeroMemory(pDiag, sizeof(struct _RtmpDiagStrcut_));
			pDiag->ArrayStartIdx = pDiag->ArrayCurIdx = 0;
			pDiag->inited = 1;
		}
		else
		{
			// Tx
			pDiag->TxFailCnt[ArrayCurIdx] = TxStaCnt0.field.TxFailCount;
			pDiag->TxAggCnt[ArrayCurIdx] = TxAggCnt.field.AggTxCount;
			pDiag->TxNonAggCnt[ArrayCurIdx] = TxAggCnt.field.NonAggTxCount;
			pDiag->TxAMPDUCnt[ArrayCurIdx][0] = TxAggCnt0.field.AggSize1Count;
			pDiag->TxAMPDUCnt[ArrayCurIdx][1] = TxAggCnt0.field.AggSize2Count;
			pDiag->TxAMPDUCnt[ArrayCurIdx][2] = TxAggCnt1.field.AggSize3Count;
			pDiag->TxAMPDUCnt[ArrayCurIdx][3] = TxAggCnt1.field.AggSize4Count;
			pDiag->TxAMPDUCnt[ArrayCurIdx][4] = TxAggCnt2.field.AggSize5Count;
			pDiag->TxAMPDUCnt[ArrayCurIdx][5] = TxAggCnt2.field.AggSize6Count;
			pDiag->TxAMPDUCnt[ArrayCurIdx][6] = TxAggCnt3.field.AggSize7Count;
			pDiag->TxAMPDUCnt[ArrayCurIdx][7] = TxAggCnt3.field.AggSize8Count;
			pDiag->TxAMPDUCnt[ArrayCurIdx][8] = TxAggCnt4.field.AggSize9Count;
			pDiag->TxAMPDUCnt[ArrayCurIdx][9] = TxAggCnt4.field.AggSize10Count;
			pDiag->TxAMPDUCnt[ArrayCurIdx][10] = TxAggCnt5.field.AggSize11Count;
			pDiag->TxAMPDUCnt[ArrayCurIdx][11] = TxAggCnt5.field.AggSize12Count;
			pDiag->TxAMPDUCnt[ArrayCurIdx][12] = TxAggCnt6.field.AggSize13Count;
			pDiag->TxAMPDUCnt[ArrayCurIdx][13] = TxAggCnt6.field.AggSize14Count;
			pDiag->TxAMPDUCnt[ArrayCurIdx][14] = TxAggCnt7.field.AggSize15Count;
			pDiag->TxAMPDUCnt[ArrayCurIdx][15] = TxAggCnt7.field.AggSize16Count;

			pDiag->RxCrcErrCnt[ArrayCurIdx] = RxStaCnt0.field.CrcErr;

			INC_RING_INDEX(pDiag->ArrayCurIdx,  DIAGNOSE_TIME);
			ArrayCurIdx = pDiag->ArrayCurIdx;
			for (i =0; i < 9; i++)
			{
				pDiag->TxDescCnt[ArrayCurIdx][i]= 0;
				pDiag->TxSWQueCnt[ArrayCurIdx][i] =0;
				pDiag->TxMcsCnt[ArrayCurIdx][i] = 0;
				pDiag->RxMcsCnt[ArrayCurIdx][i] = 0;
			}
			pDiag->TxDataCnt[ArrayCurIdx] = 0;
			pDiag->TxFailCnt[ArrayCurIdx] = 0;
			pDiag->RxDataCnt[ArrayCurIdx] = 0;
			pDiag->RxCrcErrCnt[ArrayCurIdx]  = 0;
//			for (i = 9; i < 16; i++)
			for (i = 9; i < 24; i++) // 3*3
			{
				pDiag->TxDescCnt[ArrayCurIdx][i] = 0;
				pDiag->TxMcsCnt[ArrayCurIdx][i] = 0;
				pDiag->RxMcsCnt[ArrayCurIdx][i] = 0;
}

			if (pDiag->ArrayCurIdx == pDiag->ArrayStartIdx)
				INC_RING_INDEX(pDiag->ArrayStartIdx,  DIAGNOSE_TIME);
		}

	}
#endif // DBG_DIAGNOSE //


}


/*
	========================================================================

	Routine Description:
		Reset NIC from error

	Arguments:
		Adapter						Pointer to our adapter

	Return Value:
		None

	IRQL = PASSIVE_LEVEL

	Note:
		Reset NIC from error state

	========================================================================
*/
VOID	NICResetFromError(
	IN	PRTMP_ADAPTER	pAd)
{
	// Reset BBP (according to alex, reset ASIC will force reset BBP
	// Therefore, skip the reset BBP
	// RTMP_IO_WRITE32(pAd, MAC_CSR1, 0x2);

	RTMP_IO_WRITE32(pAd, MAC_SYS_CTRL, 0x1);
	// Remove ASIC from reset state
	RTMP_IO_WRITE32(pAd, MAC_SYS_CTRL, 0x0);

	NICInitializeAdapter(pAd, FALSE);
	NICInitAsicFromEEPROM(pAd);

	// Switch to current channel, since during reset process, the connection should remains on.
	AsicSwitchChannel(pAd, pAd->CommonCfg.CentralChannel, FALSE);
	AsicLockChannel(pAd, pAd->CommonCfg.CentralChannel);
}


NDIS_STATUS NICLoadFirmware(
	IN PRTMP_ADAPTER pAd)
{
	NDIS_STATUS	 status = NDIS_STATUS_SUCCESS;
	if (pAd->chipOps.loadFirmware)
		status = pAd->chipOps.loadFirmware(pAd);

	return status;
}


/*
	========================================================================

	Routine Description:
		erase 8051 firmware image in MAC ASIC

	Arguments:
		Adapter						Pointer to our adapter

	IRQL = PASSIVE_LEVEL

	========================================================================
*/
VOID NICEraseFirmware(
	IN PRTMP_ADAPTER pAd)
{
	if (pAd->chipOps.eraseFirmware)
		pAd->chipOps.eraseFirmware(pAd);

}/* End of NICEraseFirmware */


/*
	========================================================================

	Routine Description:
		Load Tx rate switching parameters

	Arguments:
		Adapter						Pointer to our adapter

	Return Value:
		NDIS_STATUS_SUCCESS         firmware image load ok
		NDIS_STATUS_FAILURE         image not found

	IRQL = PASSIVE_LEVEL

	Rate Table Format:
		1. (B0: Valid Item number) (B1:Initial item from zero)
		2. Item Number(Dec)      Mode(Hex)     Current MCS(Dec)    TrainUp(Dec)    TrainDown(Dec)

	========================================================================
*/
NDIS_STATUS NICLoadRateSwitchingParams(
	IN PRTMP_ADAPTER pAd)
{
	return NDIS_STATUS_SUCCESS;
}


/*
	========================================================================

	Routine Description:
		Compare two memory block

	Arguments:
		pSrc1		Pointer to first memory address
		pSrc2		Pointer to second memory address

	Return Value:
		0:			memory is equal
		1:			pSrc1 memory is larger
		2:			pSrc2 memory is larger

	IRQL = DISPATCH_LEVEL

	Note:

	========================================================================
*/
ULONG	RTMPCompareMemory(
	IN	PVOID	pSrc1,
	IN	PVOID	pSrc2,
	IN	ULONG	Length)
{
	PUCHAR	pMem1;
	PUCHAR	pMem2;
	ULONG	Index = 0;

	pMem1 = (PUCHAR) pSrc1;
	pMem2 = (PUCHAR) pSrc2;

	for (Index = 0; Index < Length; Index++)
	{
		if (pMem1[Index] > pMem2[Index])
			return (1);
		else if (pMem1[Index] < pMem2[Index])
			return (2);
	}

	// Equal
	return (0);
}


/*
	========================================================================

	Routine Description:
		Zero out memory block

	Arguments:
		pSrc1		Pointer to memory address
		Length		Size

	Return Value:
		None

	IRQL = PASSIVE_LEVEL
	IRQL = DISPATCH_LEVEL

	Note:

	========================================================================
*/
VOID	RTMPZeroMemory(
	IN	PVOID	pSrc,
	IN	ULONG	Length)
{
	PUCHAR	pMem;
	ULONG	Index = 0;

	pMem = (PUCHAR) pSrc;

	for (Index = 0; Index < Length; Index++)
	{
		pMem[Index] = 0x00;
	}
}


/*
	========================================================================

	Routine Description:
		Copy data from memory block 1 to memory block 2

	Arguments:
		pDest		Pointer to destination memory address
		pSrc		Pointer to source memory address
		Length		Copy size

	Return Value:
		None

	IRQL = PASSIVE_LEVEL
	IRQL = DISPATCH_LEVEL

	Note:

	========================================================================
*/
VOID RTMPMoveMemory(
	OUT	PVOID	pDest,
	IN	PVOID	pSrc,
	IN	ULONG	Length)
{
	PUCHAR	pMem1;
	PUCHAR	pMem2;
	UINT	Index;

	ASSERT((Length==0) || (pDest && pSrc));

	pMem1 = (PUCHAR) pDest;
	pMem2 = (PUCHAR) pSrc;

	for (Index = 0; Index < Length; Index++)
	{
		pMem1[Index] = pMem2[Index];
	}
}


/*
	========================================================================

	Routine Description:
		Initialize port configuration structure

	Arguments:
		Adapter						Pointer to our adapter

	Return Value:
		None

	IRQL = PASSIVE_LEVEL

	Note:

	========================================================================
*/
VOID	UserCfgInit(
	IN	PRTMP_ADAPTER pAd)
{
//	EDCA_PARM DefaultEdcaParm;
    UINT key_index, bss_index;

	DBGPRINT(RT_DEBUG_TRACE, ("--> UserCfgInit\n"));

	//
	//  part I. intialize common configuration
	//

	for(key_index=0; key_index<SHARE_KEY_NUM; key_index++)
	{
		for(bss_index = 0; bss_index < MAX_MBSSID_NUM; bss_index++)
		{
			pAd->SharedKey[bss_index][key_index].KeyLen = 0;
			pAd->SharedKey[bss_index][key_index].CipherAlg = CIPHER_NONE;
		}
	}

	pAd->EepromAccess = FALSE;

	pAd->Antenna.word = 0;
	pAd->CommonCfg.BBPCurrentBW = BW_20;

	pAd->LedCntl.word = 0;
#ifdef RTMP_MAC_PCI
	pAd->LedIndicatorStrength = 0;
	pAd->RLnkCtrlOffset = 0;
	pAd->HostLnkCtrlOffset = 0;
#ifdef CONFIG_STA_SUPPORT
	pAd->StaCfg.PSControl.field.EnableNewPS=TRUE;
	pAd->CheckDmaBusyCount = 0;
#endif // CONFIG_STA_SUPPORT //
#endif // RTMP_MAC_PCI //

	pAd->bAutoTxAgcA = FALSE;			// Default is OFF
	pAd->bAutoTxAgcG = FALSE;			// Default is OFF
	pAd->RfIcType = RFIC_2820;

	// Init timer for reset complete event
	pAd->CommonCfg.CentralChannel = 1;
	pAd->bForcePrintTX = FALSE;
	pAd->bForcePrintRX = FALSE;
	pAd->bStaFifoTest = FALSE;
	pAd->bProtectionTest = FALSE;
	/*
	pAd->bHCCATest = FALSE;
	pAd->bGenOneHCCA = FALSE;
	*/
	pAd->CommonCfg.Dsifs = 10;      // in units of usec
	pAd->CommonCfg.TxPower = 100; //mW
	pAd->CommonCfg.TxPowerPercentage = 0xffffffff; // AUTO
	pAd->CommonCfg.TxPowerDefault = 0xffffffff; // AUTO
	pAd->CommonCfg.TxPreamble = Rt802_11PreambleAuto; // use Long preamble on TX by defaut
	pAd->CommonCfg.bUseZeroToDisableFragment = FALSE;
	pAd->CommonCfg.RtsThreshold = 2347;
	pAd->CommonCfg.FragmentThreshold = 2346;
	pAd->CommonCfg.UseBGProtection = 0;    // 0: AUTO
	pAd->CommonCfg.bEnableTxBurst = TRUE; //0;
	pAd->CommonCfg.PhyMode = 0xff;     // unknown
	pAd->CommonCfg.BandState = UNKNOWN_BAND;
	pAd->CommonCfg.RadarDetect.CSPeriod = 10;
	pAd->CommonCfg.RadarDetect.CSCount = 0;
	pAd->CommonCfg.RadarDetect.RDMode = RD_NORMAL_MODE;


#ifdef TONE_RADAR_DETECT_SUPPORT
#ifdef CARRIER_DETECTION_SUPPORT
	pAd->CommonCfg.CarrierDetect.delta = CARRIER_DETECT_DELTA;
	pAd->CommonCfg.CarrierDetect.div_flag = CARRIER_DETECT_DIV_FLAG;
	pAd->CommonCfg.CarrierDetect.criteria = CARRIER_DETECT_CRITIRIA;
#ifdef RT3090
	if(IS_RT3090A(pAd))
	pAd->CommonCfg.CarrierDetect.threshold = CARRIER_DETECT_THRESHOLD_3090A;
	else
#endif // RT3090 //
	pAd->CommonCfg.CarrierDetect.threshold = CARRIER_DETECT_THRESHOLD;
#endif // CARRIER_DETECTION_SUPPORT //
#endif // TONE_RADAR_DETECT_SUPPORT //

	pAd->CommonCfg.RadarDetect.ChMovingTime = 65;
#ifdef MERGE_ARCH_TEAM
	pAd->CommonCfg.RadarDetect.LongPulseRadarTh = 2;
	pAd->CommonCfg.RadarDetect.AvgRssiReq = -75;
#else // original rt28xx source code
	pAd->CommonCfg.RadarDetect.LongPulseRadarTh = 3;
#endif // MERGE_ARCH_TEAM //
	pAd->CommonCfg.bAPSDCapable = FALSE;
	pAd->CommonCfg.bNeedSendTriggerFrame = FALSE;
	pAd->CommonCfg.TriggerTimerCount = 0;
	pAd->CommonCfg.bAPSDForcePowerSave = FALSE;
	pAd->CommonCfg.bCountryFlag = FALSE;
	pAd->CommonCfg.TxStream = 0;
	pAd->CommonCfg.RxStream = 0;

	NdisZeroMemory(&pAd->BeaconTxWI, sizeof(pAd->BeaconTxWI));

#ifdef DOT11_N_SUPPORT
	NdisZeroMemory(&pAd->CommonCfg.HtCapability, sizeof(pAd->CommonCfg.HtCapability));
	pAd->HTCEnable = FALSE;
	pAd->bBroadComHT = FALSE;
	pAd->CommonCfg.bRdg = FALSE;

#ifdef DOT11N_DRAFT3
	pAd->CommonCfg.Dot11OBssScanPassiveDwell = dot11OBSSScanPassiveDwell;	// Unit : TU. 5~1000
	pAd->CommonCfg.Dot11OBssScanActiveDwell = dot11OBSSScanActiveDwell;	// Unit : TU. 10~1000
	pAd->CommonCfg.Dot11BssWidthTriggerScanInt = dot11BSSWidthTriggerScanInterval;	// Unit : Second
	pAd->CommonCfg.Dot11OBssScanPassiveTotalPerChannel = dot11OBSSScanPassiveTotalPerChannel;	// Unit : TU. 200~10000
	pAd->CommonCfg.Dot11OBssScanActiveTotalPerChannel = dot11OBSSScanActiveTotalPerChannel;	// Unit : TU. 20~10000
	pAd->CommonCfg.Dot11BssWidthChanTranDelayFactor = dot11BSSWidthChannelTransactionDelayFactor;
	pAd->CommonCfg.Dot11OBssScanActivityThre = dot11BSSScanActivityThreshold;	// Unit : percentage
	pAd->CommonCfg.Dot11BssWidthChanTranDelay = (pAd->CommonCfg.Dot11BssWidthTriggerScanInt * pAd->CommonCfg.Dot11BssWidthChanTranDelayFactor);
#endif  // DOT11N_DRAFT3 //

	NdisZeroMemory(&pAd->CommonCfg.AddHTInfo, sizeof(pAd->CommonCfg.AddHTInfo));
	pAd->CommonCfg.BACapability.field.MMPSmode = MMPS_ENABLE;
	pAd->CommonCfg.BACapability.field.MpduDensity = 0;
	pAd->CommonCfg.BACapability.field.Policy = IMMED_BA;
	pAd->CommonCfg.BACapability.field.RxBAWinLimit = 64; //32;
	pAd->CommonCfg.BACapability.field.TxBAWinLimit = 64; //32;
	DBGPRINT(RT_DEBUG_TRACE, ("--> UserCfgInit. BACapability = 0x%x\n", pAd->CommonCfg.BACapability.word));

	pAd->CommonCfg.BACapability.field.AutoBA = FALSE;
	BATableInit(pAd, &pAd->BATable);

	pAd->CommonCfg.bExtChannelSwitchAnnouncement = 1;
	pAd->CommonCfg.bHTProtect = 1;
	pAd->CommonCfg.bMIMOPSEnable = TRUE;
	//2008/11/05:KH add to support Antenna power-saving of AP<--
	pAd->CommonCfg.bGreenAPEnable=FALSE;
	pAd->CommonCfg.bBlockAntDivforGreenAP=FALSE;
	//2008/11/05:KH add to support Antenna power-saving of AP-->
	pAd->CommonCfg.bBADecline = FALSE;
	pAd->CommonCfg.bDisableReordering = FALSE;

	if (pAd->MACVersion == 0x28720200)
	{
		pAd->CommonCfg.TxBASize = 13; //by Jerry recommend
	}else{
		pAd->CommonCfg.TxBASize = 7;
	}

	pAd->CommonCfg.REGBACapability.word = pAd->CommonCfg.BACapability.word;
#endif // DOT11_N_SUPPORT //

	//pAd->CommonCfg.HTPhyMode.field.BW = BW_20;
	//pAd->CommonCfg.HTPhyMode.field.MCS = MCS_AUTO;
	//pAd->CommonCfg.HTPhyMode.field.ShortGI = GI_800;
	//pAd->CommonCfg.HTPhyMode.field.STBC = STBC_NONE;
	pAd->CommonCfg.TxRate = RATE_6;

	pAd->CommonCfg.MlmeTransmit.field.MCS = MCS_RATE_6;
	pAd->CommonCfg.MlmeTransmit.field.BW = BW_20;
	pAd->CommonCfg.MlmeTransmit.field.MODE = MODE_OFDM;

	pAd->CommonCfg.BeaconPeriod = 100;     // in mSec


	//
	// part II. intialize STA specific configuration
	//
#ifdef CONFIG_STA_SUPPORT
	IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
	{
		RX_FILTER_SET_FLAG(pAd, fRX_FILTER_ACCEPT_DIRECT);
		RX_FILTER_CLEAR_FLAG(pAd, fRX_FILTER_ACCEPT_MULTICAST);
		RX_FILTER_SET_FLAG(pAd, fRX_FILTER_ACCEPT_BROADCAST);
		RX_FILTER_SET_FLAG(pAd, fRX_FILTER_ACCEPT_ALL_MULTICAST);

		pAd->StaCfg.Psm = PWR_ACTIVE;

		pAd->StaCfg.OrigWepStatus = Ndis802_11EncryptionDisabled;
		pAd->StaCfg.PairCipher = Ndis802_11EncryptionDisabled;
		pAd->StaCfg.GroupCipher = Ndis802_11EncryptionDisabled;
		pAd->StaCfg.bMixCipher = FALSE;
		pAd->StaCfg.DefaultKeyId = 0;

		// 802.1x port control
		pAd->StaCfg.PrivacyFilter = Ndis802_11PrivFilter8021xWEP;
		pAd->StaCfg.PortSecured = WPA_802_1X_PORT_NOT_SECURED;
		pAd->StaCfg.LastMicErrorTime = 0;
		pAd->StaCfg.MicErrCnt        = 0;
		pAd->StaCfg.bBlockAssoc      = FALSE;
		pAd->StaCfg.WpaState         = SS_NOTUSE;

		pAd->CommonCfg.NdisRadioStateOff = FALSE;		// New to support microsoft disable radio with OID command

		pAd->StaCfg.RssiTrigger = 0;
		NdisZeroMemory(&pAd->StaCfg.RssiSample, sizeof(RSSI_SAMPLE));
		pAd->StaCfg.RssiTriggerMode = RSSI_TRIGGERED_UPON_BELOW_THRESHOLD;
		pAd->StaCfg.AtimWin = 0;
		pAd->StaCfg.DefaultListenCount = 3;//default listen count;
		pAd->StaCfg.BssType = BSS_INFRA;  // BSS_INFRA or BSS_ADHOC or BSS_MONITOR
		pAd->StaCfg.bScanReqIsFromWebUI = FALSE;
		OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_DOZE);
		OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_WAKEUP_NOW);

		pAd->StaCfg.bAutoTxRateSwitch = TRUE;
		pAd->StaCfg.DesiredTransmitSetting.field.MCS = MCS_AUTO;
	}

#ifdef EXT_BUILD_CHANNEL_LIST
	pAd->StaCfg.IEEE80211dClientMode = Rt802_11_D_None;
#endif // EXT_BUILD_CHANNEL_LIST //
#ifdef PCIE_PS_SUPPORT
pAd->brt30xxBanMcuCmd = FALSE;
pAd->b3090ESpecialChip = FALSE;
//KH Debug:the following must be removed
pAd->StaCfg.PSControl.field.rt30xxPowerMode=3;
pAd->StaCfg.PSControl.field.rt30xxForceASPMTest=0;
pAd->StaCfg.PSControl.field.rt30xxFollowHostASPM=1;
#endif // PCIE_PS_SUPPORT //
#endif // CONFIG_STA_SUPPORT //

	// global variables mXXXX used in MAC protocol state machines
	OPSTATUS_SET_FLAG(pAd, fOP_STATUS_RECEIVE_DTIM);
	OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_ADHOC_ON);
	OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_INFRA_ON);

	// PHY specification
	pAd->CommonCfg.PhyMode = PHY_11BG_MIXED;		// default PHY mode
	OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_SHORT_PREAMBLE_INUSED);  // CCK use LONG preamble

#ifdef CONFIG_STA_SUPPORT
	IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
	{
		// user desired power mode
		pAd->StaCfg.WindowsPowerMode = Ndis802_11PowerModeCAM;
		pAd->StaCfg.WindowsBatteryPowerMode = Ndis802_11PowerModeCAM;
		pAd->StaCfg.bWindowsACCAMEnable = FALSE;

		RTMPInitTimer(pAd, &pAd->StaCfg.StaQuickResponeForRateUpTimer, GET_TIMER_FUNCTION(StaQuickResponeForRateUpExec), pAd, FALSE);
		pAd->StaCfg.StaQuickResponeForRateUpTimerRunning = FALSE;

		// Patch for Ndtest
		pAd->StaCfg.ScanCnt = 0;

		pAd->StaCfg.bHwRadio  = TRUE; // Default Hardware Radio status is On
		pAd->StaCfg.bSwRadio  = TRUE; // Default Software Radio status is On
		pAd->StaCfg.bRadio    = TRUE; // bHwRadio && bSwRadio
		pAd->StaCfg.bHardwareRadio = FALSE;		// Default is OFF
		pAd->StaCfg.bShowHiddenSSID = FALSE;		// Default no show

		// Nitro mode control
		pAd->StaCfg.bAutoReconnect = TRUE;

		// Save the init time as last scan time, the system should do scan after 2 seconds.
		// This patch is for driver wake up from standby mode, system will do scan right away.
		NdisGetSystemUpTime(&pAd->StaCfg.LastScanTime);
		if (pAd->StaCfg.LastScanTime > 10 * OS_HZ)
			pAd->StaCfg.LastScanTime -= (10 * OS_HZ);

		NdisZeroMemory(pAd->nickname, IW_ESSID_MAX_SIZE+1);
#ifdef RTMP_MAC_PCI
		sprintf((PSTRING) pAd->nickname, "RT2860STA");
#endif // RTMP_MAC_PCI //
		RTMPInitTimer(pAd, &pAd->StaCfg.WpaDisassocAndBlockAssocTimer, GET_TIMER_FUNCTION(WpaDisassocApAndBlockAssoc), pAd, FALSE);
#ifdef WPA_SUPPLICANT_SUPPORT
		pAd->StaCfg.IEEE8021X = FALSE;
		pAd->StaCfg.IEEE8021x_required_keys = FALSE;
		pAd->StaCfg.WpaSupplicantUP = WPA_SUPPLICANT_DISABLE;
		pAd->StaCfg.bRSN_IE_FromWpaSupplicant = FALSE;
#ifdef NATIVE_WPA_SUPPLICANT_SUPPORT
		pAd->StaCfg.WpaSupplicantUP = WPA_SUPPLICANT_ENABLE;
#endif // NATIVE_WPA_SUPPLICANT_SUPPORT //
#endif // WPA_SUPPLICANT_SUPPORT //

		NdisZeroMemory(pAd->StaCfg.ReplayCounter, 8);


		pAd->StaCfg.bAutoConnectByBssid = FALSE;
		pAd->StaCfg.BeaconLostTime = BEACON_LOST_TIME;
		NdisZeroMemory(pAd->StaCfg.WpaPassPhrase, 64);
		pAd->StaCfg.WpaPassPhraseLen = 0;
		pAd->StaCfg.bAutoRoaming = FALSE;
		pAd->StaCfg.bForceTxBurst = FALSE;
	}
#endif // CONFIG_STA_SUPPORT //

	// Default for extra information is not valid
	pAd->ExtraInfo = EXTRA_INFO_CLEAR;

	// Default Config change flag
	pAd->bConfigChanged = FALSE;

	//
	// part III. AP configurations
	//


	//
	// part IV. others
	//
	// dynamic BBP R66:sensibity tuning to overcome background noise
	pAd->BbpTuning.bEnable                = TRUE;
	pAd->BbpTuning.FalseCcaLowerThreshold = 100;
	pAd->BbpTuning.FalseCcaUpperThreshold = 512;
	pAd->BbpTuning.R66Delta               = 4;
	pAd->Mlme.bEnableAutoAntennaCheck = TRUE;

	//
	// Also initial R66CurrentValue, RTUSBResumeMsduTransmission might use this value.
	// if not initial this value, the default value will be 0.
	//
	pAd->BbpTuning.R66CurrentValue = 0x38;

	pAd->Bbp94 = BBPR94_DEFAULT;
	pAd->BbpForCCK = FALSE;

	// Default is FALSE for test bit 1
	//pAd->bTest1 = FALSE;

	// initialize MAC table and allocate spin lock
	NdisZeroMemory(&pAd->MacTab, sizeof(MAC_TABLE));
	InitializeQueueHeader(&pAd->MacTab.McastPsQueue);
	NdisAllocateSpinLock(&pAd->MacTabLock);

	//RTMPInitTimer(pAd, &pAd->RECBATimer, RECBATimerTimeout, pAd, TRUE);
	//RTMPSetTimer(&pAd->RECBATimer, REORDER_EXEC_INTV);

#ifdef RALINK_ATE
	NdisZeroMemory(&pAd->ate, sizeof(ATE_INFO));
	pAd->ate.Mode = ATE_STOP;
	pAd->ate.TxCount = 200;/* to exceed TX_RING_SIZE ... */
	pAd->ate.TxDoneCount = 0;
	pAd->ate.RFFreqOffset = 0;
	pAd->ate.TxLength = 1024;
	pAd->ate.TxWI.ShortGI = 0;// LONG GI : 800 ns
	pAd->ate.TxWI.PHYMODE = MODE_CCK;
	pAd->ate.TxWI.MCS = 3;
	pAd->ate.TxWI.BW = BW_20;
	pAd->ate.Channel = 1;
	pAd->ate.QID = QID_AC_BE;
	pAd->ate.Addr1[0] = 0x00;
	pAd->ate.Addr1[1] = 0x11;
	pAd->ate.Addr1[2] = 0x22;
	pAd->ate.Addr1[3] = 0xAA;
	pAd->ate.Addr1[4] = 0xBB;
	pAd->ate.Addr1[5] = 0xCC;
	NdisMoveMemory(pAd->ate.Addr2, pAd->ate.Addr1, ETH_LENGTH_OF_ADDRESS);
	NdisMoveMemory(pAd->ate.Addr3, pAd->ate.Addr1, ETH_LENGTH_OF_ADDRESS);
	pAd->ate.bRxFER = 0;
	pAd->ate.bQATxStart = FALSE;
	pAd->ate.bQARxStart = FALSE;

#ifdef RTMP_MAC_PCI
	pAd->ate.bFWLoading = FALSE;
#endif // RTMP_MAC_PCI //


#ifdef RALINK_28xx_QA
	pAd->ate.TxStatus = 0;
	pAd->ate.AtePid = THREAD_PID_INIT_VALUE;
#endif // RALINK_28xx_QA //
#endif // RALINK_ATE //


	pAd->CommonCfg.bWiFiTest = FALSE;
#ifdef RTMP_MAC_PCI
    pAd->bPCIclkOff = FALSE;
#endif // RTMP_MAC_PCI //

#ifdef CONFIG_STA_SUPPORT
RTMP_SET_PSFLAG(pAd, fRTMP_PS_CAN_GO_SLEEP);
#endif // CONFIG_STA_SUPPORT //
#ifdef ANT_DIVERSITY_SUPPORT
		if ( pAd->CommonCfg.bRxAntDiversity == ANT_FIX_ANT2)
		{
			pAd->RxAnt.Pair1PrimaryRxAnt = 1;
			pAd->RxAnt.Pair1SecondaryRxAnt = 0;
		}
		else // Default
		{
			pAd->RxAnt.Pair1PrimaryRxAnt = 0;
			pAd->RxAnt.Pair1SecondaryRxAnt = 1;
		}
		pAd->RxAnt.EvaluatePeriod = 0;
		pAd->RxAnt.RcvPktNumWhenEvaluate = 0;
#ifdef CONFIG_STA_SUPPORT
		pAd->RxAnt.Pair1AvgRssi[0] = pAd->RxAnt.Pair1AvgRssi[1] = 0;
#endif // CONFIG_STA_SUPPORT //
#endif // AP_ANTENNA_DIVERSITY_SUPPORT //

	DBGPRINT(RT_DEBUG_TRACE, ("<-- UserCfgInit\n"));
}

// IRQL = PASSIVE_LEVEL
UCHAR BtoH(STRING ch)
{
	if (ch >= '0' && ch <= '9') return (ch - '0');        // Handle numerals
	if (ch >= 'A' && ch <= 'F') return (ch - 'A' + 0xA);  // Handle capitol hex digits
	if (ch >= 'a' && ch <= 'f') return (ch - 'a' + 0xA);  // Handle small hex digits
	return(255);
}

//
//  FUNCTION: AtoH(char *, UCHAR *, int)
//
//  PURPOSE:  Converts ascii string to network order hex
//
//  PARAMETERS:
//    src    - pointer to input ascii string
//    dest   - pointer to output hex
//    destlen - size of dest
//
//  COMMENTS:
//
//    2 ascii bytes make a hex byte so must put 1st ascii byte of pair
//    into upper nibble and 2nd ascii byte of pair into lower nibble.
//
// IRQL = PASSIVE_LEVEL

void AtoH(PSTRING src, PUCHAR dest, int destlen)
{
	PSTRING srcptr;
	PUCHAR destTemp;

	srcptr = src;
	destTemp = (PUCHAR) dest;

	while(destlen--)
	{
		*destTemp = BtoH(*srcptr++) << 4;    // Put 1st ascii byte in upper nibble.
		*destTemp += BtoH(*srcptr++);      // Add 2nd ascii byte to above.
		destTemp++;
	}
}


//+++Mark by shiang, not use now, need to remove after confirm
//---Mark by shiang, not use now, need to remove after confirm


/*
	========================================================================

	Routine Description:
		Init timer objects

	Arguments:
		pAd			Pointer to our adapter
		pTimer				Timer structure
		pTimerFunc			Function to execute when timer expired
		Repeat				Ture for period timer

	Return Value:
		None

	Note:

	========================================================================
*/
VOID	RTMPInitTimer(
	IN	PRTMP_ADAPTER			pAd,
	IN	PRALINK_TIMER_STRUCT	pTimer,
	IN	PVOID					pTimerFunc,
	IN	PVOID					pData,
	IN	BOOLEAN					Repeat)
{
	//
	// Set Valid to TRUE for later used.
	// It will crash if we cancel a timer or set a timer
	// that we haven't initialize before.
	//
	pTimer->Valid      = TRUE;

	pTimer->PeriodicType = Repeat;
	pTimer->State      = FALSE;
	pTimer->cookie = (ULONG) pData;

#ifdef RTMP_TIMER_TASK_SUPPORT
	pTimer->pAd = pAd;
#endif // RTMP_TIMER_TASK_SUPPORT //

	RTMP_OS_Init_Timer(pAd, &pTimer->TimerObj,	pTimerFunc, (PVOID) pTimer);
}


/*
	========================================================================

	Routine Description:
		Init timer objects

	Arguments:
		pTimer				Timer structure
		Value				Timer value in milliseconds

	Return Value:
		None

	Note:
		To use this routine, must call RTMPInitTimer before.

	========================================================================
*/
VOID	RTMPSetTimer(
	IN	PRALINK_TIMER_STRUCT	pTimer,
	IN	ULONG					Value)
{
	if (pTimer->Valid)
	{
		pTimer->TimerValue = Value;
		pTimer->State      = FALSE;
		if (pTimer->PeriodicType == TRUE)
		{
			pTimer->Repeat = TRUE;
			RTMP_SetPeriodicTimer(&pTimer->TimerObj, Value);
		}
		else
		{
			pTimer->Repeat = FALSE;
			RTMP_OS_Add_Timer(&pTimer->TimerObj, Value);
		}
	}
	else
	{
		DBGPRINT_ERR(("RTMPSetTimer failed, Timer hasn't been initialize!\n"));
	}
}


/*
	========================================================================

	Routine Description:
		Init timer objects

	Arguments:
		pTimer				Timer structure
		Value				Timer value in milliseconds

	Return Value:
		None

	Note:
		To use this routine, must call RTMPInitTimer before.

	========================================================================
*/
VOID	RTMPModTimer(
	IN	PRALINK_TIMER_STRUCT	pTimer,
	IN	ULONG					Value)
{
	BOOLEAN	Cancel;

	if (pTimer->Valid)
	{
		pTimer->TimerValue = Value;
		pTimer->State      = FALSE;
		if (pTimer->PeriodicType == TRUE)
		{
			RTMPCancelTimer(pTimer, &Cancel);
			RTMPSetTimer(pTimer, Value);
		}
		else
		{
			RTMP_OS_Mod_Timer(&pTimer->TimerObj, Value);
		}
	}
	else
	{
		DBGPRINT_ERR(("RTMPModTimer failed, Timer hasn't been initialize!\n"));
	}
}


/*
	========================================================================

	Routine Description:
		Cancel timer objects

	Arguments:
		Adapter						Pointer to our adapter

	Return Value:
		None

	IRQL = PASSIVE_LEVEL
	IRQL = DISPATCH_LEVEL

	Note:
		1.) To use this routine, must call RTMPInitTimer before.
		2.) Reset NIC to initial state AS IS system boot up time.

	========================================================================
*/
VOID	RTMPCancelTimer(
	IN	PRALINK_TIMER_STRUCT	pTimer,
	OUT	BOOLEAN					*pCancelled)
{
	if (pTimer->Valid)
	{
		if (pTimer->State == FALSE)
			pTimer->Repeat = FALSE;

		RTMP_OS_Del_Timer(&pTimer->TimerObj, pCancelled);

		if (*pCancelled == TRUE)
			pTimer->State = TRUE;

#ifdef RTMP_TIMER_TASK_SUPPORT
		// We need to go-through the TimerQ to findout this timer handler and remove it if
		//		it's still waiting for execution.
		RtmpTimerQRemove(pTimer->pAd, pTimer);
#endif // RTMP_TIMER_TASK_SUPPORT //
	}
	else
	{
		DBGPRINT_ERR(("RTMPCancelTimer failed, Timer hasn't been initialize!\n"));
	}
}


/*
	========================================================================

	Routine Description:
		Set LED Status

	Arguments:
		pAd						Pointer to our adapter
		Status					LED Status

	Return Value:
		None

	IRQL = PASSIVE_LEVEL
	IRQL = DISPATCH_LEVEL

	Note:

	========================================================================
*/
VOID RTMPSetLED(
	IN PRTMP_ADAPTER	pAd,
	IN UCHAR			Status)
{
	//ULONG			data;
	UCHAR			HighByte = 0;
	UCHAR			LowByte;
	BOOLEAN			bIgnored = FALSE;

#ifdef RALINK_ATE
	/*
		In ATE mode of RT2860 AP/STA, we have erased 8051 firmware.
		So LED mode is not supported when ATE is running.
	*/
	if (!IS_RT3572(pAd))
	{
		if (ATE_ON(pAd))
			return;
	}
#endif // RALINK_ATE //

	LowByte = pAd->LedCntl.field.LedMode&0x7f;
	switch (Status)
	{
		case LED_LINK_DOWN:
			HighByte = 0x20;
			AsicSendCommandToMcu(pAd, 0x50, 0xff, LowByte, HighByte);
			pAd->LedIndicatorStrength = 0;
			break;
		case LED_LINK_UP:
			if (pAd->CommonCfg.Channel > 14)
				HighByte = 0xa0;
			else
				HighByte = 0x60;
			AsicSendCommandToMcu(pAd, 0x50, 0xff, LowByte, HighByte);
			break;
		case LED_RADIO_ON:
			HighByte = 0x20;
			AsicSendCommandToMcu(pAd, 0x50, 0xff, LowByte, HighByte);
			break;
		case LED_HALT:
			LowByte = 0; // Driver sets MAC register and MAC controls LED
		case LED_RADIO_OFF:
			HighByte = 0;
			AsicSendCommandToMcu(pAd, 0x50, 0xff, LowByte, HighByte);
			break;
		case LED_WPS:
			HighByte = 0x10;
			AsicSendCommandToMcu(pAd, 0x50, 0xff, LowByte, HighByte);
			break;
		case LED_ON_SITE_SURVEY:
			HighByte = 0x08;
			AsicSendCommandToMcu(pAd, 0x50, 0xff, LowByte, HighByte);
			break;
		case LED_POWER_UP:
			HighByte = 0x04;
			AsicSendCommandToMcu(pAd, 0x50, 0xff, LowByte, HighByte);
			break;
#ifdef RALINK_ATE
#endif // RALINK_ATE //
		default:
			DBGPRINT(RT_DEBUG_WARN, ("RTMPSetLED::Unknown Status %d\n", Status));
			break;
	}

    //
	// Keep LED status for LED SiteSurvey mode.
	// After SiteSurvey, we will set the LED mode to previous status.
	//
	if ((Status != LED_ON_SITE_SURVEY) && (Status != LED_POWER_UP) && (bIgnored == FALSE))
		pAd->LedStatus = Status;

	DBGPRINT(RT_DEBUG_TRACE, ("RTMPSetLED::Mode=%d,HighByte=0x%02x,LowByte=0x%02x\n", pAd->LedCntl.field.LedMode, HighByte, LowByte));
}

/*
	========================================================================

	Routine Description:
		Set LED Signal Stregth

	Arguments:
		pAd						Pointer to our adapter
		Dbm						Signal Stregth

	Return Value:
		None

	IRQL = PASSIVE_LEVEL

	Note:
		Can be run on any IRQL level.

		According to Microsoft Zero Config Wireless Signal Stregth definition as belows.
		<= -90  No Signal
		<= -81  Very Low
		<= -71  Low
		<= -67  Good
		<= -57  Very Good
		 > -57  Excellent
	========================================================================
*/
VOID RTMPSetSignalLED(
	IN PRTMP_ADAPTER	pAd,
	IN NDIS_802_11_RSSI Dbm)
{
	UCHAR		nLed = 0;

	if (pAd->LedCntl.field.LedMode == LED_MODE_SIGNAL_STREGTH)
	{
		if (Dbm <= -90)
			nLed = 0;
		else if (Dbm <= -81)
			nLed = 1;
		else if (Dbm <= -71)
			nLed = 3;
		else if (Dbm <= -67)
			nLed = 7;
		else if (Dbm <= -57)
			nLed = 15;
		else
			nLed = 31;

		//
		// Update Signal Stregth to firmware if changed.
		//
		if (pAd->LedIndicatorStrength != nLed)
		{
			AsicSendCommandToMcu(pAd, 0x51, 0xff, nLed, pAd->LedCntl.field.Polarity);
			pAd->LedIndicatorStrength = nLed;
		}
	}
}


/*
	========================================================================

	Routine Description:
		Enable RX

	Arguments:
		pAd						Pointer to our adapter

	Return Value:
		None

	IRQL <= DISPATCH_LEVEL

	Note:
		Before Enable RX, make sure you have enabled Interrupt.
	========================================================================
*/
VOID RTMPEnableRxTx(
	IN PRTMP_ADAPTER	pAd)
{
//	WPDMA_GLO_CFG_STRUC	GloCfg;
//	ULONG	i = 0;
	UINT32 rx_filter_flag;

	DBGPRINT(RT_DEBUG_TRACE, ("==> RTMPEnableRxTx\n"));

	// Enable Rx DMA.
	RT28XXDMAEnable(pAd);

	// enable RX of MAC block
	if (pAd->OpMode == OPMODE_AP)
	{
		rx_filter_flag = APNORMAL;


		RTMP_IO_WRITE32(pAd, RX_FILTR_CFG, rx_filter_flag);     // enable RX of DMA block
	}
	else
	{
		if (pAd->CommonCfg.PSPXlink)
			rx_filter_flag = PSPXLINK;
		else
			rx_filter_flag = STANORMAL;     // Staion not drop control frame will fail WiFi Certification.
		RTMP_IO_WRITE32(pAd, RX_FILTR_CFG, rx_filter_flag);
	}

	RTMP_IO_WRITE32(pAd, MAC_SYS_CTRL, 0xc);
	DBGPRINT(RT_DEBUG_TRACE, ("<== RTMPEnableRxTx\n"));
}


//+++Add by shiang, move from os/linux/rt_main_dev.c
void CfgInitHook(PRTMP_ADAPTER pAd)
{
	pAd->bBroadComHT = TRUE;
}


int rt28xx_init(
	IN PRTMP_ADAPTER pAd,
	IN PSTRING pDefaultMac,
	IN PSTRING pHostName)
{
	UINT					index;
	UCHAR					TmpPhy;
	NDIS_STATUS				Status;
	UINT32					MacCsr0 = 0;

#ifdef CONFIG_STA_SUPPORT
#ifdef RTMP_MAC_PCI
	IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
	{
	// If dirver doesn't wake up firmware here,
	// NICLoadFirmware will hang forever when interface is up again.
	// RT2860 PCI
	if (OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_DOZE) &&
		OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_PCIE_DEVICE))
	{
		AUTO_WAKEUP_STRUC AutoWakeupCfg;
			AsicForceWakeup(pAd, TRUE);
		AutoWakeupCfg.word = 0;
		RTMP_IO_WRITE32(pAd, AUTO_WAKEUP_CFG, AutoWakeupCfg.word);
		OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_DOZE);
	}
	}
#endif // RTMP_MAC_PCI //
#endif // CONFIG_STA_SUPPORT //


	// reset Adapter flags
	RTMP_CLEAR_FLAGS(pAd);

	// Init BssTab & ChannelInfo tabbles for auto channel select.

#ifdef DOT11_N_SUPPORT
	// Allocate BA Reordering memory
	ba_reordering_resource_init(pAd, MAX_REORDERING_MPDU_NUM);
#endif // DOT11_N_SUPPORT //

	// Make sure MAC gets ready.
	index = 0;
	do
	{
		RTMP_IO_READ32(pAd, MAC_CSR0, &MacCsr0);
		pAd->MACVersion = MacCsr0;

		if ((pAd->MACVersion != 0x00) && (pAd->MACVersion != 0xFFFFFFFF))
			break;

		RTMPusecDelay(10);
	} while (index++ < 100);
	DBGPRINT(RT_DEBUG_TRACE, ("MAC_CSR0  [ Ver:Rev=0x%08x]\n", pAd->MACVersion));

#ifdef RTMP_MAC_PCI
#ifdef PCIE_PS_SUPPORT
	/*Iverson patch PCIE L1 issue to make sure that driver can be read,write ,BBP and RF register  at pcie L.1 level */
	if ((IS_RT3090(pAd) || IS_RT3572(pAd) || IS_RT3390(pAd))&&OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_PCIE_DEVICE))
	{
		RTMP_IO_READ32(pAd, AUX_CTRL, &MacCsr0);
		MacCsr0 |= 0x402;
		RTMP_IO_WRITE32(pAd, AUX_CTRL, MacCsr0);
		DBGPRINT(RT_DEBUG_TRACE, ("AUX_CTRL = 0x%x\n", MacCsr0));
	}
#endif // PCIE_PS_SUPPORT //

	// To fix driver disable/enable hang issue when radio off
	RTMP_IO_WRITE32(pAd, PWR_PIN_CFG, 0x2);
#endif // RTMP_MAC_PCI //

	// Disable DMA
	RT28XXDMADisable(pAd);


	// Load 8051 firmware
	Status = NICLoadFirmware(pAd);
	if (Status != NDIS_STATUS_SUCCESS)
	{
		DBGPRINT_ERR(("NICLoadFirmware failed, Status[=0x%08x]\n", Status));
		goto err1;
	}

	NICLoadRateSwitchingParams(pAd);

	// Disable interrupts here which is as soon as possible
	// This statement should never be true. We might consider to remove it later
#ifdef RTMP_MAC_PCI
	if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_ACTIVE))
	{
		RTMP_ASIC_INTERRUPT_DISABLE(pAd);
	}
#endif // RTMP_MAC_PCI //

	Status = RTMPAllocTxRxRingMemory(pAd);
	if (Status != NDIS_STATUS_SUCCESS)
	{
		DBGPRINT_ERR(("RTMPAllocDMAMemory failed, Status[=0x%08x]\n", Status));
		goto err1;
	}

	RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);

	// initialize MLME
	//

	Status = RtmpMgmtTaskInit(pAd);
	if (Status != NDIS_STATUS_SUCCESS)
		goto err2;

	Status = MlmeInit(pAd);
	if (Status != NDIS_STATUS_SUCCESS)
	{
		DBGPRINT_ERR(("MlmeInit failed, Status[=0x%08x]\n", Status));
		goto err2;
	}

	// Initialize pAd->StaCfg, pAd->ApCfg, pAd->CommonCfg to manufacture default
	//
	UserCfgInit(pAd);
	Status = RtmpNetTaskInit(pAd);
	if (Status != NDIS_STATUS_SUCCESS)
		goto err3;

//	COPY_MAC_ADDR(pAd->ApCfg.MBSSID[apidx].Bssid, netif->hwaddr);
//	pAd->bForcePrintTX = TRUE;

	CfgInitHook(pAd);


#ifdef BLOCK_NET_IF
	initblockQueueTab(pAd);
#endif // BLOCK_NET_IF //

#ifdef CONFIG_STA_SUPPORT
	IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
		NdisAllocateSpinLock(&pAd->MacTabLock);
#endif // CONFIG_STA_SUPPORT //

	MeasureReqTabInit(pAd);
	TpcReqTabInit(pAd);

	//
	// Init the hardware, we need to init asic before read registry, otherwise mac register will be reset
	//
	Status = NICInitializeAdapter(pAd, TRUE);
	if (Status != NDIS_STATUS_SUCCESS)
	{
		DBGPRINT_ERR(("NICInitializeAdapter failed, Status[=0x%08x]\n", Status));
		if (Status != NDIS_STATUS_SUCCESS)
		goto err3;
	}

	// Read parameters from Config File
	Status = RTMPReadParametersHook(pAd);

	DBGPRINT(RT_DEBUG_OFF, ("1. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
	if (Status != NDIS_STATUS_SUCCESS)
	{
		DBGPRINT_ERR(("NICReadRegParameters failed, Status[=0x%08x]\n",Status));
		goto err4;
	}


#ifdef DOT11_N_SUPPORT
	//Init Ba Capability parameters.
//	RT28XX_BA_INIT(pAd);
	pAd->CommonCfg.DesiredHtPhy.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
	pAd->CommonCfg.DesiredHtPhy.AmsduEnable = (USHORT)pAd->CommonCfg.BACapability.field.AmsduEnable;
	pAd->CommonCfg.DesiredHtPhy.AmsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
	pAd->CommonCfg.DesiredHtPhy.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
	// UPdata to HT IE
	pAd->CommonCfg.HtCapability.HtCapInfo.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
	pAd->CommonCfg.HtCapability.HtCapInfo.AMsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
	pAd->CommonCfg.HtCapability.HtCapParm.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
#endif // DOT11_N_SUPPORT //

	// after reading Registry, we now know if in AP mode or STA mode

	// Load 8051 firmware; crash when FW image not existent
	// Status = NICLoadFirmware(pAd);
	// if (Status != NDIS_STATUS_SUCCESS)
	//    break;

	DBGPRINT(RT_DEBUG_OFF, ("2. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));

	// We should read EEPROM for all cases.  rt2860b
	NICReadEEPROMParameters(pAd, (PUCHAR)pDefaultMac);
#ifdef CONFIG_STA_SUPPORT
#endif // CONFIG_STA_SUPPORT //

	DBGPRINT(RT_DEBUG_OFF, ("3. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));

	NICInitAsicFromEEPROM(pAd); //rt2860b

	// Set PHY to appropriate mode
	TmpPhy = pAd->CommonCfg.PhyMode;
	pAd->CommonCfg.PhyMode = 0xff;
	RTMPSetPhyMode(pAd, TmpPhy);
#ifdef DOT11_N_SUPPORT
	SetCommonHT(pAd);
#endif // DOT11_N_SUPPORT //

	// No valid channels.
	if (pAd->ChannelListNum == 0)
	{
		DBGPRINT(RT_DEBUG_ERROR, ("Wrong configuration. No valid channel found. Check \"ContryCode\" and \"ChannelGeography\" setting.\n"));
		goto err4;
	}

#ifdef DOT11_N_SUPPORT
	DBGPRINT(RT_DEBUG_OFF, ("MCS Set = %02x %02x %02x %02x %02x\n", pAd->CommonCfg.HtCapability.MCSSet[0],
           pAd->CommonCfg.HtCapability.MCSSet[1], pAd->CommonCfg.HtCapability.MCSSet[2],
           pAd->CommonCfg.HtCapability.MCSSet[3], pAd->CommonCfg.HtCapability.MCSSet[4]));
#endif // DOT11_N_SUPPORT //

#ifdef RTMP_RF_RW_SUPPORT
	//Init RT30xx RFRegisters after read RFIC type from EEPROM
	NICInitRFRegisters(pAd);
#endif // RTMP_RF_RW_SUPPORT //


//		APInitialize(pAd);

#ifdef IKANOS_VX_1X0
	VR_IKANOS_FP_Init(pAd->ApCfg.BssidNum, pAd->PermanentAddress);
#endif // IKANOS_VX_1X0 //

		//
	// Initialize RF register to default value
	//
	AsicSwitchChannel(pAd, pAd->CommonCfg.Channel, FALSE);
	AsicLockChannel(pAd, pAd->CommonCfg.Channel);

	// 8051 firmware require the signal during booting time.
	//2008/11/28:KH marked the following codes to patch Frequency offset bug
	//AsicSendCommandToMcu(pAd, 0x72, 0xFF, 0x00, 0x00);

	if (pAd && (Status != NDIS_STATUS_SUCCESS))
	{
		//
		// Undo everything if it failed
		//
		if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE))
		{
//			NdisMDeregisterInterrupt(&pAd->Interrupt);
			RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
		}
//		RTMPFreeAdapter(pAd); // we will free it in disconnect()
	}
	else if (pAd)
	{
		// Microsoft HCT require driver send a disconnect event after driver initialization.
		OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_MEDIA_STATE_CONNECTED);
//		pAd->IndicateMediaState = NdisMediaStateDisconnected;
		RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_MEDIA_STATE_CHANGE);

		DBGPRINT(RT_DEBUG_TRACE, ("NDIS_STATUS_MEDIA_DISCONNECT Event B!\n"));


	}// end of else


	// Set up the Mac address
	RtmpOSNetDevAddrSet(pAd->net_dev, &pAd->CurrentAddress[0]);

	// Various AP function init


#ifdef CONFIG_STA_SUPPORT
	IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
	{
#ifdef WPA_SUPPLICANT_SUPPORT
#ifndef NATIVE_WPA_SUPPLICANT_SUPPORT
		// send wireless event to wpa_supplicant for infroming interface up.
		RtmpOSWrielessEventSend(pAd, IWEVCUSTOM, RT_INTERFACE_UP, NULL, NULL, 0);
#endif // NATIVE_WPA_SUPPLICANT_SUPPORT //
#endif // WPA_SUPPLICANT_SUPPORT //

	}
#endif // CONFIG_STA_SUPPORT //


	DBGPRINT_S(Status, ("<==== rt28xx_init, Status=%x\n", Status));

	return TRUE;


err4:
err3:
	MlmeHalt(pAd);
err2:
	RTMPFreeTxRxRingMemory(pAd);
err1:

#ifdef DOT11_N_SUPPORT
	os_free_mem(pAd, pAd->mpdu_blk_pool.mem); // free BA pool
#endif // DOT11_N_SUPPORT //

	// shall not set priv to NULL here because the priv didn't been free yet.
	//net_dev->priv = 0;
#ifdef INF_AMAZON_SE
err0:
#endif // INF_AMAZON_SE //
#ifdef ST
err0:
#endif // ST //

	DBGPRINT(RT_DEBUG_ERROR, ("!!! rt28xx Initialized fail !!!\n"));
	return FALSE;
}
//---Add by shiang, move from os/linux/rt_main_dev.c


static INT RtmpChipOpsRegister(
	IN RTMP_ADAPTER *pAd,
	IN INT			infType)
{
	RTMP_CHIP_OP	*pChipOps = &pAd->chipOps;
	int status;

	memset(pChipOps, 0, sizeof(RTMP_CHIP_OP));

	/* set eeprom related hook functions */
	status = RtmpChipOpsEepromHook(pAd, infType);

	/* set mcu related hook functions */
	switch(infType)
	{
#ifdef RTMP_PCI_SUPPORT
		case RTMP_DEV_INF_PCI:
			pChipOps->loadFirmware = RtmpAsicLoadFirmware;
			pChipOps->eraseFirmware = RtmpAsicEraseFirmware;
			pChipOps->sendCommandToMcu = RtmpAsicSendCommandToMcu;
			break;
#endif // RTMP_PCI_SUPPORT //


		default:
			break;
	}

	return status;
}


INT RtmpRaDevCtrlInit(
	IN RTMP_ADAPTER *pAd,
	IN RTMP_INF_TYPE infType)
{
	//VOID	*handle;

	// Assign the interface type. We need use it when do register/EEPROM access.
	pAd->infType = infType;


#ifdef CONFIG_STA_SUPPORT
	pAd->OpMode = OPMODE_STA;
	DBGPRINT(RT_DEBUG_TRACE, ("STA Driver version-%s\n", STA_DRIVER_VERSION));
#endif // CONFIG_STA_SUPPORT //


	RtmpChipOpsRegister(pAd, infType);

#ifdef MULTIPLE_CARD_SUPPORT
{
	extern BOOLEAN RTMP_CardInfoRead(PRTMP_ADAPTER pAd);

	// find its profile path
	pAd->MC_RowID = -1; // use default profile path
	RTMP_CardInfoRead(pAd);

	if (pAd->MC_RowID == -1)
#ifdef CONFIG_STA_SUPPORT
		strcpy(pAd->MC_FileName, STA_PROFILE_PATH);
#endif // CONFIG_STA_SUPPORT //

	DBGPRINT(RT_DEBUG_TRACE, ("MC> ROW = %d, PATH = %s\n", pAd->MC_RowID, pAd->MC_FileName));
}
#endif // MULTIPLE_CARD_SUPPORT //

	return 0;
}


BOOLEAN RtmpRaDevCtrlExit(IN RTMP_ADAPTER *pAd)
{
#ifdef MULTIPLE_CARD_SUPPORT
extern UINT8  MC_CardUsed[MAX_NUM_OF_MULTIPLE_CARD];

	if ((pAd->MC_RowID >= 0) && (pAd->MC_RowID <= MAX_NUM_OF_MULTIPLE_CARD))
		MC_CardUsed[pAd->MC_RowID] = 0; // not clear MAC address
#endif // MULTIPLE_CARD_SUPPORT //


	RTMPFreeAdapter(pAd);

	return TRUE;
}


// not yet support MBSS
PNET_DEV get_netdev_from_bssid(
	IN	PRTMP_ADAPTER	pAd,
	IN	UCHAR			FromWhichBSSID)
{
	PNET_DEV dev_p = NULL;


#ifdef CONFIG_STA_SUPPORT
	IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
	{
		dev_p = pAd->net_dev;
	}
#endif // CONFIG_STA_SUPPORT //

	ASSERT(dev_p);
	return dev_p; /* return one of MBSS */
}