drivers/staging/olpc_dcon/olpc_dcon_xo_1.c - kernel/mindspeed - Git at Google

 /*
  * Mainly by David Woodhouse, somewhat modified by Jordan Crouse
  *
  * Copyright © 2006-2007  Red Hat, Inc.
  * Copyright © 2006-2007  Advanced Micro Devices, Inc.
  * Copyright © 2009       VIA Technology, Inc.
  * Copyright (c) 2010  Andres Salomon <dilinger@queued.net>
  *
  * This program is free software.  You can redistribute it and/or
  * modify it under the terms of version 2 of the GNU General Public
  * License as published by the Free Software Foundation.
  */
 #include <linux/cs5535.h>
 #include <linux/gpio.h>
 #include <linux/delay.h>
 #include <asm/olpc.h>

 #include "olpc_dcon.h"

 static int dcon_init_xo_1(struct dcon_priv *dcon)
 {
 	unsigned char lob;

 	if (gpio_request(OLPC_GPIO_DCON_STAT0, "OLPC-DCON")) {
 		printk(KERN_ERR "olpc-dcon: failed to request STAT0 GPIO\n");
 		return -EIO;
 	}
 	if (gpio_request(OLPC_GPIO_DCON_STAT1, "OLPC-DCON")) {
 		printk(KERN_ERR "olpc-dcon: failed to request STAT1 GPIO\n");
 		goto err_gp_stat1;
 	}
 	if (gpio_request(OLPC_GPIO_DCON_IRQ, "OLPC-DCON")) {
 		printk(KERN_ERR "olpc-dcon: failed to request IRQ GPIO\n");
 		goto err_gp_irq;
 	}
 	if (gpio_request(OLPC_GPIO_DCON_LOAD, "OLPC-DCON")) {
 		printk(KERN_ERR "olpc-dcon: failed to request LOAD GPIO\n");
 		goto err_gp_load;
 	}
 	if (gpio_request(OLPC_GPIO_DCON_BLANK, "OLPC-DCON")) {
 		printk(KERN_ERR "olpc-dcon: failed to request BLANK GPIO\n");
 		goto err_gp_blank;
 	}

 	/* Turn off the event enable for GPIO7 just to be safe */
 	cs5535_gpio_clear(OLPC_GPIO_DCON_IRQ, GPIO_EVENTS_ENABLE);

 	/*
 	 * Determine the current state by reading the GPIO bit; earlier
 	 * stages of the boot process have established the state.
 	 *
 	 * Note that we read GPIO_OUPUT_VAL rather than GPIO_READ_BACK here;
 	 * this is because OFW will disable input for the pin and set a value..
 	 * READ_BACK will only contain a valid value if input is enabled and
 	 * then a value is set.  So, future readings of the pin can use
 	 * READ_BACK, but the first one cannot.  Awesome, huh?
 	 */
 	dcon->curr_src = cs5535_gpio_isset(OLPC_GPIO_DCON_LOAD, GPIO_OUTPUT_VAL)
 		? DCON_SOURCE_CPU
 		: DCON_SOURCE_DCON;
 	dcon->pending_src = dcon->curr_src;

 	/* Set the directions for the GPIO pins */
 	gpio_direction_input(OLPC_GPIO_DCON_STAT0);
 	gpio_direction_input(OLPC_GPIO_DCON_STAT1);
 	gpio_direction_input(OLPC_GPIO_DCON_IRQ);
 	gpio_direction_input(OLPC_GPIO_DCON_BLANK);
 	gpio_direction_output(OLPC_GPIO_DCON_LOAD,
 			dcon->curr_src == DCON_SOURCE_CPU);

 	/* Set up the interrupt mappings */

 	/* Set the IRQ to pair 2 */
 	cs5535_gpio_setup_event(OLPC_GPIO_DCON_IRQ, 2, 0);

 	/* Enable group 2 to trigger the DCON interrupt */
 	cs5535_gpio_set_irq(2, DCON_IRQ);

 	/* Select edge level for interrupt (in PIC) */
 	lob = inb(0x4d0);
 	lob &= ~(1 << DCON_IRQ);
 	outb(lob, 0x4d0);

 	/* Register the interrupt handler */
 	if (request_irq(DCON_IRQ, &dcon_interrupt, 0, "DCON", dcon)) {
 		printk(KERN_ERR "olpc-dcon: failed to request DCON's irq\n");
 		goto err_req_irq;
 	}

 	/* Clear INV_EN for GPIO7 (DCONIRQ) */
 	cs5535_gpio_clear(OLPC_GPIO_DCON_IRQ, GPIO_INPUT_INVERT);

 	/* Enable filter for GPIO12 (DCONBLANK) */
 	cs5535_gpio_set(OLPC_GPIO_DCON_BLANK, GPIO_INPUT_FILTER);

 	/* Disable filter for GPIO7 */
 	cs5535_gpio_clear(OLPC_GPIO_DCON_IRQ, GPIO_INPUT_FILTER);

 	/* Disable event counter for GPIO7 (DCONIRQ) and GPIO12 (DCONBLANK) */
 	cs5535_gpio_clear(OLPC_GPIO_DCON_IRQ, GPIO_INPUT_EVENT_COUNT);
 	cs5535_gpio_clear(OLPC_GPIO_DCON_BLANK, GPIO_INPUT_EVENT_COUNT);

 	/* Add GPIO12 to the Filter Event Pair #7 */
 	cs5535_gpio_set(OLPC_GPIO_DCON_BLANK, GPIO_FE7_SEL);

 	/* Turn off negative Edge Enable for GPIO12 */
 	cs5535_gpio_clear(OLPC_GPIO_DCON_BLANK, GPIO_NEGATIVE_EDGE_EN);

 	/* Enable negative Edge Enable for GPIO7 */
 	cs5535_gpio_set(OLPC_GPIO_DCON_IRQ, GPIO_NEGATIVE_EDGE_EN);

 	/* Zero the filter amount for Filter Event Pair #7 */
 	cs5535_gpio_set(0, GPIO_FLTR7_AMOUNT);

 	/* Clear the negative edge status for GPIO7 and GPIO12 */
 	cs5535_gpio_set(OLPC_GPIO_DCON_IRQ, GPIO_NEGATIVE_EDGE_STS);
 	cs5535_gpio_set(OLPC_GPIO_DCON_BLANK, GPIO_NEGATIVE_EDGE_STS);

 	/* FIXME:  Clear the posiitive status as well, just to be sure */
 	cs5535_gpio_set(OLPC_GPIO_DCON_IRQ, GPIO_POSITIVE_EDGE_STS);
 	cs5535_gpio_set(OLPC_GPIO_DCON_BLANK, GPIO_POSITIVE_EDGE_STS);

 	/* Enable events for GPIO7 (DCONIRQ) and GPIO12 (DCONBLANK) */
 	cs5535_gpio_set(OLPC_GPIO_DCON_IRQ, GPIO_EVENTS_ENABLE);
 	cs5535_gpio_set(OLPC_GPIO_DCON_BLANK, GPIO_EVENTS_ENABLE);

 	return 0;

 err_req_irq:
 	gpio_free(OLPC_GPIO_DCON_BLANK);
 err_gp_blank:
 	gpio_free(OLPC_GPIO_DCON_LOAD);
 err_gp_load:
 	gpio_free(OLPC_GPIO_DCON_IRQ);
 err_gp_irq:
 	gpio_free(OLPC_GPIO_DCON_STAT1);
 err_gp_stat1:
 	gpio_free(OLPC_GPIO_DCON_STAT0);
 	return -EIO;
 }

 static void dcon_wiggle_xo_1(void)
 {
 	int x;

 	/*
 	 * According to HiMax, when powering the DCON up we should hold
 	 * SMB_DATA high for 8 SMB_CLK cycles.  This will force the DCON
 	 * state machine to reset to a (sane) initial state.  Mitch Bradley
 	 * did some testing and discovered that holding for 16 SMB_CLK cycles
 	 * worked a lot more reliably, so that's what we do here.
 	 *
 	 * According to the cs5536 spec, to set GPIO14 to SMB_CLK we must
 	 * simultaneously set AUX1 IN/OUT to GPIO14; ditto for SMB_DATA and
 	 * GPIO15.
 	 */
 	cs5535_gpio_set(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_VAL);
 	cs5535_gpio_set(OLPC_GPIO_SMB_DATA, GPIO_OUTPUT_VAL);
 	cs5535_gpio_set(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_ENABLE);
 	cs5535_gpio_set(OLPC_GPIO_SMB_DATA, GPIO_OUTPUT_ENABLE);
 	cs5535_gpio_clear(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_AUX1);
 	cs5535_gpio_clear(OLPC_GPIO_SMB_DATA, GPIO_OUTPUT_AUX1);
 	cs5535_gpio_clear(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_AUX2);
 	cs5535_gpio_clear(OLPC_GPIO_SMB_DATA, GPIO_OUTPUT_AUX2);
 	cs5535_gpio_clear(OLPC_GPIO_SMB_CLK, GPIO_INPUT_AUX1);
 	cs5535_gpio_clear(OLPC_GPIO_SMB_DATA, GPIO_INPUT_AUX1);

 	for (x = 0; x < 16; x++) {
 		udelay(5);
 		cs5535_gpio_clear(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_VAL);
 		udelay(5);
 		cs5535_gpio_set(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_VAL);
 	}
 	udelay(5);
 	cs5535_gpio_set(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_AUX1);
 	cs5535_gpio_set(OLPC_GPIO_SMB_DATA, GPIO_OUTPUT_AUX1);
 	cs5535_gpio_set(OLPC_GPIO_SMB_CLK, GPIO_INPUT_AUX1);
 	cs5535_gpio_set(OLPC_GPIO_SMB_DATA, GPIO_INPUT_AUX1);
 }

 static void dcon_set_dconload_1(int val)
 {
 	gpio_set_value(OLPC_GPIO_DCON_LOAD, val);
 }

 static u8 dcon_read_status_xo_1(void)
 {
 	u8 status;

 	status = gpio_get_value(OLPC_GPIO_DCON_STAT0);
 	status |= gpio_get_value(OLPC_GPIO_DCON_STAT1) << 1;

 	/* Clear the negative edge status for GPIO7 */
 	cs5535_gpio_set(OLPC_GPIO_DCON_IRQ, GPIO_NEGATIVE_EDGE_STS);

 	return status;
 }

 struct dcon_platform_data dcon_pdata_xo_1 = {
 	.init = dcon_init_xo_1,
 	.bus_stabilize_wiggle = dcon_wiggle_xo_1,
 	.set_dconload = dcon_set_dconload_1,
 	.read_status = dcon_read_status_xo_1,
 };
	/*
	* Mainly by David Woodhouse, somewhat modified by Jordan Crouse
	*
	* Copyright © 2006-2007 Red Hat, Inc.
	* Copyright © 2006-2007 Advanced Micro Devices, Inc.
	* Copyright © 2009 VIA Technology, Inc.
	* Copyright (c) 2010 Andres Salomon <dilinger@queued.net>
	*
	* This program is free software. You can redistribute it and/or
	* modify it under the terms of version 2 of the GNU General Public
	* License as published by the Free Software Foundation.
	*/
	#include <linux/cs5535.h>
	#include <linux/gpio.h>
	#include <linux/delay.h>
	#include <asm/olpc.h>

	#include "olpc_dcon.h"

	static int dcon_init_xo_1(struct dcon_priv *dcon)
	{
	unsigned char lob;

	if (gpio_request(OLPC_GPIO_DCON_STAT0, "OLPC-DCON")) {
	printk(KERN_ERR "olpc-dcon: failed to request STAT0 GPIO\n");
	return -EIO;
	}
	if (gpio_request(OLPC_GPIO_DCON_STAT1, "OLPC-DCON")) {
	printk(KERN_ERR "olpc-dcon: failed to request STAT1 GPIO\n");
	goto err_gp_stat1;
	}
	if (gpio_request(OLPC_GPIO_DCON_IRQ, "OLPC-DCON")) {
	printk(KERN_ERR "olpc-dcon: failed to request IRQ GPIO\n");
	goto err_gp_irq;
	}
	if (gpio_request(OLPC_GPIO_DCON_LOAD, "OLPC-DCON")) {
	printk(KERN_ERR "olpc-dcon: failed to request LOAD GPIO\n");
	goto err_gp_load;
	}
	if (gpio_request(OLPC_GPIO_DCON_BLANK, "OLPC-DCON")) {
	printk(KERN_ERR "olpc-dcon: failed to request BLANK GPIO\n");
	goto err_gp_blank;
	}

	/* Turn off the event enable for GPIO7 just to be safe */
	cs5535_gpio_clear(OLPC_GPIO_DCON_IRQ, GPIO_EVENTS_ENABLE);

	/*
	* Determine the current state by reading the GPIO bit; earlier
	* stages of the boot process have established the state.
	*
	* Note that we read GPIO_OUPUT_VAL rather than GPIO_READ_BACK here;
	* this is because OFW will disable input for the pin and set a value..
	* READ_BACK will only contain a valid value if input is enabled and
	* then a value is set. So, future readings of the pin can use
	* READ_BACK, but the first one cannot. Awesome, huh?
	*/
	dcon->curr_src = cs5535_gpio_isset(OLPC_GPIO_DCON_LOAD, GPIO_OUTPUT_VAL)
	? DCON_SOURCE_CPU
	: DCON_SOURCE_DCON;
	dcon->pending_src = dcon->curr_src;

	/* Set the directions for the GPIO pins */
	gpio_direction_input(OLPC_GPIO_DCON_STAT0);
	gpio_direction_input(OLPC_GPIO_DCON_STAT1);
	gpio_direction_input(OLPC_GPIO_DCON_IRQ);
	gpio_direction_input(OLPC_GPIO_DCON_BLANK);
	gpio_direction_output(OLPC_GPIO_DCON_LOAD,
	dcon->curr_src == DCON_SOURCE_CPU);

	/* Set up the interrupt mappings */

	/* Set the IRQ to pair 2 */
	cs5535_gpio_setup_event(OLPC_GPIO_DCON_IRQ, 2, 0);

	/* Enable group 2 to trigger the DCON interrupt */
	cs5535_gpio_set_irq(2, DCON_IRQ);

	/* Select edge level for interrupt (in PIC) */
	lob = inb(0x4d0);
	lob &= ~(1 << DCON_IRQ);
	outb(lob, 0x4d0);

	/* Register the interrupt handler */
	if (request_irq(DCON_IRQ, &dcon_interrupt, 0, "DCON", dcon)) {
	printk(KERN_ERR "olpc-dcon: failed to request DCON's irq\n");
	goto err_req_irq;
	}

	/* Clear INV_EN for GPIO7 (DCONIRQ) */
	cs5535_gpio_clear(OLPC_GPIO_DCON_IRQ, GPIO_INPUT_INVERT);

	/* Enable filter for GPIO12 (DCONBLANK) */
	cs5535_gpio_set(OLPC_GPIO_DCON_BLANK, GPIO_INPUT_FILTER);

	/* Disable filter for GPIO7 */
	cs5535_gpio_clear(OLPC_GPIO_DCON_IRQ, GPIO_INPUT_FILTER);

	/* Disable event counter for GPIO7 (DCONIRQ) and GPIO12 (DCONBLANK) */
	cs5535_gpio_clear(OLPC_GPIO_DCON_IRQ, GPIO_INPUT_EVENT_COUNT);
	cs5535_gpio_clear(OLPC_GPIO_DCON_BLANK, GPIO_INPUT_EVENT_COUNT);

	/* Add GPIO12 to the Filter Event Pair #7 */
	cs5535_gpio_set(OLPC_GPIO_DCON_BLANK, GPIO_FE7_SEL);

	/* Turn off negative Edge Enable for GPIO12 */
	cs5535_gpio_clear(OLPC_GPIO_DCON_BLANK, GPIO_NEGATIVE_EDGE_EN);

	/* Enable negative Edge Enable for GPIO7 */
	cs5535_gpio_set(OLPC_GPIO_DCON_IRQ, GPIO_NEGATIVE_EDGE_EN);

	/* Zero the filter amount for Filter Event Pair #7 */
	cs5535_gpio_set(0, GPIO_FLTR7_AMOUNT);

	/* Clear the negative edge status for GPIO7 and GPIO12 */
	cs5535_gpio_set(OLPC_GPIO_DCON_IRQ, GPIO_NEGATIVE_EDGE_STS);
	cs5535_gpio_set(OLPC_GPIO_DCON_BLANK, GPIO_NEGATIVE_EDGE_STS);

	/* FIXME: Clear the posiitive status as well, just to be sure */
	cs5535_gpio_set(OLPC_GPIO_DCON_IRQ, GPIO_POSITIVE_EDGE_STS);
	cs5535_gpio_set(OLPC_GPIO_DCON_BLANK, GPIO_POSITIVE_EDGE_STS);

	/* Enable events for GPIO7 (DCONIRQ) and GPIO12 (DCONBLANK) */
	cs5535_gpio_set(OLPC_GPIO_DCON_IRQ, GPIO_EVENTS_ENABLE);
	cs5535_gpio_set(OLPC_GPIO_DCON_BLANK, GPIO_EVENTS_ENABLE);

	return 0;

	err_req_irq:
	gpio_free(OLPC_GPIO_DCON_BLANK);
	err_gp_blank:
	gpio_free(OLPC_GPIO_DCON_LOAD);
	err_gp_load:
	gpio_free(OLPC_GPIO_DCON_IRQ);
	err_gp_irq:
	gpio_free(OLPC_GPIO_DCON_STAT1);
	err_gp_stat1:
	gpio_free(OLPC_GPIO_DCON_STAT0);
	return -EIO;
	}

	static void dcon_wiggle_xo_1(void)
	{
	int x;

	/*
	* According to HiMax, when powering the DCON up we should hold
	* SMB_DATA high for 8 SMB_CLK cycles. This will force the DCON
	* state machine to reset to a (sane) initial state. Mitch Bradley
	* did some testing and discovered that holding for 16 SMB_CLK cycles
	* worked a lot more reliably, so that's what we do here.
	*
	* According to the cs5536 spec, to set GPIO14 to SMB_CLK we must
	* simultaneously set AUX1 IN/OUT to GPIO14; ditto for SMB_DATA and
	* GPIO15.
	*/
	cs5535_gpio_set(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_VAL);
	cs5535_gpio_set(OLPC_GPIO_SMB_DATA, GPIO_OUTPUT_VAL);
	cs5535_gpio_set(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_ENABLE);
	cs5535_gpio_set(OLPC_GPIO_SMB_DATA, GPIO_OUTPUT_ENABLE);
	cs5535_gpio_clear(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_AUX1);
	cs5535_gpio_clear(OLPC_GPIO_SMB_DATA, GPIO_OUTPUT_AUX1);
	cs5535_gpio_clear(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_AUX2);
	cs5535_gpio_clear(OLPC_GPIO_SMB_DATA, GPIO_OUTPUT_AUX2);
	cs5535_gpio_clear(OLPC_GPIO_SMB_CLK, GPIO_INPUT_AUX1);
	cs5535_gpio_clear(OLPC_GPIO_SMB_DATA, GPIO_INPUT_AUX1);

	for (x = 0; x < 16; x++) {
	udelay(5);
	cs5535_gpio_clear(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_VAL);
	udelay(5);
	cs5535_gpio_set(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_VAL);
	}
	udelay(5);
	cs5535_gpio_set(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_AUX1);
	cs5535_gpio_set(OLPC_GPIO_SMB_DATA, GPIO_OUTPUT_AUX1);
	cs5535_gpio_set(OLPC_GPIO_SMB_CLK, GPIO_INPUT_AUX1);
	cs5535_gpio_set(OLPC_GPIO_SMB_DATA, GPIO_INPUT_AUX1);
	}

	static void dcon_set_dconload_1(int val)
	{
	gpio_set_value(OLPC_GPIO_DCON_LOAD, val);
	}

	static u8 dcon_read_status_xo_1(void)
	{
	u8 status;

	status = gpio_get_value(OLPC_GPIO_DCON_STAT0);
	status \|= gpio_get_value(OLPC_GPIO_DCON_STAT1) << 1;

	/* Clear the negative edge status for GPIO7 */
	cs5535_gpio_set(OLPC_GPIO_DCON_IRQ, GPIO_NEGATIVE_EDGE_STS);

	return status;
	}

	struct dcon_platform_data dcon_pdata_xo_1 = {
	.init = dcon_init_xo_1,
	.bus_stabilize_wiggle = dcon_wiggle_xo_1,
	.set_dconload = dcon_set_dconload_1,
	.read_status = dcon_read_status_xo_1,
	};