| /* |
| * Aic79xx register and scratch ram definitions. |
| * |
| * Copyright (c) 1994-2001, 2004 Justin T. Gibbs. |
| * Copyright (c) 2000-2002 Adaptec Inc. |
| * All rights reserved. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions |
| * are met: |
| * 1. Redistributions of source code must retain the above copyright |
| * notice, this list of conditions, and the following disclaimer, |
| * without modification. |
| * 2. Redistributions in binary form must reproduce at minimum a disclaimer |
| * substantially similar to the "NO WARRANTY" disclaimer below |
| * ("Disclaimer") and any redistribution must be conditioned upon |
| * including a substantially similar Disclaimer requirement for further |
| * binary redistribution. |
| * 3. Neither the names of the above-listed copyright holders nor the names |
| * of any contributors may be used to endorse or promote products derived |
| * from this software without specific prior written permission. |
| * |
| * Alternatively, this software may be distributed under the terms of the |
| * GNU General Public License ("GPL") version 2 as published by the Free |
| * Software Foundation. |
| * |
| * NO WARRANTY |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS |
| * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT |
| * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR |
| * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT |
| * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL |
| * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS |
| * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) |
| * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, |
| * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING |
| * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE |
| * POSSIBILITY OF SUCH DAMAGES. |
| * |
| * $FreeBSD$ |
| */ |
| VERSION = "$Id: //depot/aic7xxx/aic7xxx/aic79xx.reg#77 $" |
| |
| /* |
| * This file is processed by the aic7xxx_asm utility for use in assembling |
| * firmware for the aic79xx family of SCSI host adapters as well as to generate |
| * a C header file for use in the kernel portion of the Aic79xx driver. |
| */ |
| |
| /* Register window Modes */ |
| #define M_DFF0 0 |
| #define M_DFF1 1 |
| #define M_CCHAN 2 |
| #define M_SCSI 3 |
| #define M_CFG 4 |
| #define M_DST_SHIFT 4 |
| |
| #define MK_MODE(src, dst) ((src) | ((dst) << M_DST_SHIFT)) |
| #define SET_MODE(src, dst) \ |
| SET_SRC_MODE src; \ |
| SET_DST_MODE dst; \ |
| if ((ahd->bugs & AHD_SET_MODE_BUG) != 0) { \ |
| mvi MK_MODE(src, dst) call set_mode_work_around; \ |
| } else { \ |
| mvi MODE_PTR, MK_MODE(src, dst); \ |
| } |
| |
| #define RESTORE_MODE(mode) \ |
| if ((ahd->bugs & AHD_SET_MODE_BUG) != 0) { \ |
| mov mode call set_mode_work_around; \ |
| } else { \ |
| mov MODE_PTR, mode; \ |
| } |
| |
| #define SET_SEQINTCODE(code) \ |
| if ((ahd->bugs & AHD_INTCOLLISION_BUG) != 0) { \ |
| mvi code call set_seqint_work_around; \ |
| } else { \ |
| mvi SEQINTCODE, code; \ |
| } |
| |
| /* |
| * Registers marked "dont_generate_debug_code" are not (yet) referenced |
| * from the driver code, and this keyword inhibit generation |
| * of debug code for them. |
| * |
| * REG_PRETTY_PRINT config will complain if dont_generate_debug_code |
| * is added to the register which is referenced in the driver. |
| * Unreferenced register with no dont_generate_debug_code will result |
| * in dead code. No warning is issued. |
| */ |
| |
| /* |
| * Mode Pointer |
| * Controls which of the 5, 512byte, address spaces should be used |
| * as the source and destination of any register accesses in our |
| * register window. |
| */ |
| register MODE_PTR { |
| address 0x000 |
| access_mode RW |
| field DST_MODE 0x70 |
| field SRC_MODE 0x07 |
| mode_pointer |
| dont_generate_debug_code |
| } |
| |
| const SRC_MODE_SHIFT 0 |
| const DST_MODE_SHIFT 4 |
| |
| /* |
| * Host Interrupt Status |
| */ |
| register INTSTAT { |
| address 0x001 |
| access_mode RW |
| field HWERRINT 0x80 |
| field BRKADRINT 0x40 |
| field SWTMINT 0x20 |
| field PCIINT 0x10 |
| field SCSIINT 0x08 |
| field SEQINT 0x04 |
| field CMDCMPLT 0x02 |
| field SPLTINT 0x01 |
| mask INT_PEND 0xFF |
| } |
| |
| /* |
| * Sequencer Interrupt Code |
| */ |
| register SEQINTCODE { |
| address 0x002 |
| access_mode RW |
| field { |
| NO_SEQINT, /* No seqint pending. */ |
| BAD_PHASE, /* unknown scsi bus phase */ |
| SEND_REJECT, /* sending a message reject */ |
| PROTO_VIOLATION, /* Protocol Violation */ |
| NO_MATCH, /* no cmd match for reconnect */ |
| IGN_WIDE_RES, /* Complex IGN Wide Res Msg */ |
| PDATA_REINIT, /* |
| * Returned to data phase |
| * that requires data |
| * transfer pointers to be |
| * recalculated from the |
| * transfer residual. |
| */ |
| HOST_MSG_LOOP, /* |
| * The bus is ready for the |
| * host to perform another |
| * message transaction. This |
| * mechanism is used for things |
| * like sync/wide negotiation |
| * that require a kernel based |
| * message state engine. |
| */ |
| BAD_STATUS, /* Bad status from target */ |
| DATA_OVERRUN, /* |
| * Target attempted to write |
| * beyond the bounds of its |
| * command. |
| */ |
| MKMSG_FAILED, /* |
| * Target completed command |
| * without honoring our ATN |
| * request to issue a message. |
| */ |
| MISSED_BUSFREE, /* |
| * The sequencer never saw |
| * the bus go free after |
| * either a command complete |
| * or disconnect message. |
| */ |
| DUMP_CARD_STATE, |
| ILLEGAL_PHASE, |
| INVALID_SEQINT, |
| CFG4ISTAT_INTR, |
| STATUS_OVERRUN, |
| CFG4OVERRUN, |
| ENTERING_NONPACK, |
| TASKMGMT_FUNC_COMPLETE, /* |
| * Task management function |
| * request completed with |
| * an expected busfree. |
| */ |
| TASKMGMT_CMD_CMPLT_OKAY, /* |
| * A command with a non-zero |
| * task management function |
| * has completed via the normal |
| * command completion method |
| * for commands with a zero |
| * task management function. |
| * This happens when an attempt |
| * to abort a command loses |
| * the race for the command to |
| * complete normally. |
| */ |
| TRACEPOINT0, |
| TRACEPOINT1, |
| TRACEPOINT2, |
| TRACEPOINT3, |
| SAW_HWERR, |
| BAD_SCB_STATUS |
| } |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Clear Host Interrupt |
| */ |
| register CLRINT { |
| address 0x003 |
| access_mode WO |
| count 19 |
| field CLRHWERRINT 0x80 /* Rev B or greater */ |
| field CLRBRKADRINT 0x40 |
| field CLRSWTMINT 0x20 |
| field CLRPCIINT 0x10 |
| field CLRSCSIINT 0x08 |
| field CLRSEQINT 0x04 |
| field CLRCMDINT 0x02 |
| field CLRSPLTINT 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Error Register |
| */ |
| register ERROR { |
| address 0x004 |
| access_mode RO |
| field CIOPARERR 0x80 |
| field CIOACCESFAIL 0x40 /* Rev B or greater */ |
| field MPARERR 0x20 |
| field DPARERR 0x10 |
| field SQPARERR 0x08 |
| field ILLOPCODE 0x04 |
| field DSCTMOUT 0x02 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Clear Error |
| */ |
| register CLRERR { |
| address 0x004 |
| access_mode WO |
| field CLRCIOPARERR 0x80 |
| field CLRCIOACCESFAIL 0x40 /* Rev B or greater */ |
| field CLRMPARERR 0x20 |
| field CLRDPARERR 0x10 |
| field CLRSQPARERR 0x08 |
| field CLRILLOPCODE 0x04 |
| field CLRDSCTMOUT 0x02 |
| } |
| |
| /* |
| * Host Control Register |
| * Overall host control of the device. |
| */ |
| register HCNTRL { |
| address 0x005 |
| access_mode RW |
| count 12 |
| field SEQ_RESET 0x80 /* Rev B or greater */ |
| field POWRDN 0x40 |
| field SWINT 0x10 |
| field SWTIMER_START_B 0x08 /* Rev B or greater */ |
| field PAUSE 0x04 |
| field INTEN 0x02 |
| field CHIPRST 0x01 |
| field CHIPRSTACK 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Host New SCB Queue Offset |
| */ |
| register HNSCB_QOFF { |
| address 0x006 |
| access_mode RW |
| size 2 |
| count 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Host Empty SCB Queue Offset |
| */ |
| register HESCB_QOFF { |
| address 0x008 |
| access_mode RW |
| count 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Host Mailbox |
| */ |
| register HS_MAILBOX { |
| address 0x00B |
| access_mode RW |
| mask HOST_TQINPOS 0x80 /* Boundary at either 0 or 128 */ |
| mask ENINT_COALESCE 0x40 /* Perform interrupt coalescing */ |
| } |
| |
| /* |
| * Sequencer Interrupt Status |
| */ |
| register SEQINTSTAT { |
| address 0x00C |
| count 1 |
| access_mode RO |
| field SEQ_SWTMRTO 0x10 |
| field SEQ_SEQINT 0x08 |
| field SEQ_SCSIINT 0x04 |
| field SEQ_PCIINT 0x02 |
| field SEQ_SPLTINT 0x01 |
| } |
| |
| /* |
| * Clear SEQ Interrupt |
| */ |
| register CLRSEQINTSTAT { |
| address 0x00C |
| access_mode WO |
| field CLRSEQ_SWTMRTO 0x10 |
| field CLRSEQ_SEQINT 0x08 |
| field CLRSEQ_SCSIINT 0x04 |
| field CLRSEQ_PCIINT 0x02 |
| field CLRSEQ_SPLTINT 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Software Timer |
| */ |
| register SWTIMER { |
| address 0x00E |
| access_mode RW |
| size 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SEQ New SCB Queue Offset |
| */ |
| register SNSCB_QOFF { |
| address 0x010 |
| access_mode RW |
| size 2 |
| modes M_CCHAN |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SEQ Empty SCB Queue Offset |
| */ |
| register SESCB_QOFF { |
| address 0x012 |
| count 2 |
| access_mode RW |
| modes M_CCHAN |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SEQ Done SCB Queue Offset |
| */ |
| register SDSCB_QOFF { |
| address 0x014 |
| access_mode RW |
| modes M_CCHAN |
| size 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Queue Offset Control & Status |
| */ |
| register QOFF_CTLSTA { |
| address 0x016 |
| access_mode RW |
| modes M_CCHAN |
| field EMPTY_SCB_AVAIL 0x80 |
| field NEW_SCB_AVAIL 0x40 |
| field SDSCB_ROLLOVR 0x20 |
| field HS_MAILBOX_ACT 0x10 |
| field SCB_QSIZE 0x0F { |
| SCB_QSIZE_4, |
| SCB_QSIZE_8, |
| SCB_QSIZE_16, |
| SCB_QSIZE_32, |
| SCB_QSIZE_64, |
| SCB_QSIZE_128, |
| SCB_QSIZE_256, |
| SCB_QSIZE_512, |
| SCB_QSIZE_1024, |
| SCB_QSIZE_2048, |
| SCB_QSIZE_4096, |
| SCB_QSIZE_8192, |
| SCB_QSIZE_16384 |
| } |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Interrupt Control |
| */ |
| register INTCTL { |
| address 0x018 |
| access_mode RW |
| field SWTMINTMASK 0x80 |
| field SWTMINTEN 0x40 |
| field SWTIMER_START 0x20 |
| field AUTOCLRCMDINT 0x10 |
| field PCIINTEN 0x08 |
| field SCSIINTEN 0x04 |
| field SEQINTEN 0x02 |
| field SPLTINTEN 0x01 |
| } |
| |
| /* |
| * Data FIFO Control |
| */ |
| register DFCNTRL { |
| address 0x019 |
| access_mode RW |
| modes M_DFF0, M_DFF1 |
| count 11 |
| field PRELOADEN 0x80 |
| field SCSIENWRDIS 0x40 /* Rev B only. */ |
| field SCSIEN 0x20 |
| field SCSIENACK 0x20 |
| field HDMAEN 0x08 |
| field HDMAENACK 0x08 |
| field DIRECTION 0x04 |
| field DIRECTIONACK 0x04 |
| field FIFOFLUSH 0x02 |
| field FIFOFLUSHACK 0x02 |
| field DIRECTIONEN 0x01 |
| } |
| |
| /* |
| * Device Space Command 0 |
| */ |
| register DSCOMMAND0 { |
| address 0x019 |
| count 1 |
| access_mode RW |
| modes M_CFG |
| field CACHETHEN 0x80 /* Cache Threshold enable */ |
| field DPARCKEN 0x40 /* Data Parity Check Enable */ |
| field MPARCKEN 0x20 /* Memory Parity Check Enable */ |
| field EXTREQLCK 0x10 /* External Request Lock */ |
| field DISABLE_TWATE 0x02 /* Rev B or greater */ |
| field CIOPARCKEN 0x01 /* Internal bus parity error enable */ |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Data FIFO Status |
| */ |
| register DFSTATUS { |
| address 0x01A |
| access_mode RO |
| modes M_DFF0, M_DFF1 |
| field PRELOAD_AVAIL 0x80 |
| field PKT_PRELOAD_AVAIL 0x40 |
| field MREQPEND 0x10 |
| field HDONE 0x08 |
| field DFTHRESH 0x04 |
| field FIFOFULL 0x02 |
| field FIFOEMP 0x01 |
| } |
| |
| /* |
| * S/G Cache Pointer |
| */ |
| register SG_CACHE_PRE { |
| address 0x01B |
| access_mode WO |
| modes M_DFF0, M_DFF1 |
| field SG_ADDR_MASK 0xf8 |
| field ODD_SEG 0x04 |
| field LAST_SEG 0x02 |
| dont_generate_debug_code |
| } |
| |
| register SG_CACHE_SHADOW { |
| address 0x01B |
| access_mode RO |
| modes M_DFF0, M_DFF1 |
| field SG_ADDR_MASK 0xf8 |
| field ODD_SEG 0x04 |
| field LAST_SEG 0x02 |
| field LAST_SEG_DONE 0x01 |
| } |
| |
| /* |
| * Arbiter Control |
| */ |
| register ARBCTL { |
| address 0x01B |
| access_mode RW |
| modes M_CFG |
| field RESET_HARB 0x80 |
| field RETRY_SWEN 0x08 |
| field USE_TIME 0x07 |
| } |
| |
| /* |
| * Data Channel Host Address |
| */ |
| register HADDR { |
| address 0x070 |
| access_mode RW |
| size 8 |
| modes M_DFF0, M_DFF1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Host Overlay DMA Address |
| */ |
| register HODMAADR { |
| address 0x070 |
| access_mode RW |
| size 8 |
| modes M_SCSI |
| } |
| |
| /* |
| * PCI PLL Delay. |
| */ |
| register PLLDELAY { |
| address 0x070 |
| access_mode RW |
| size 1 |
| modes M_CFG |
| field SPLIT_DROP_REQ 0x80 |
| } |
| |
| /* |
| * Data Channel Host Count |
| */ |
| register HCNT { |
| address 0x078 |
| access_mode RW |
| size 3 |
| modes M_DFF0, M_DFF1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Host Overlay DMA Count |
| */ |
| register HODMACNT { |
| address 0x078 |
| access_mode RW |
| size 2 |
| modes M_SCSI |
| } |
| |
| /* |
| * Host Overlay DMA Enable |
| */ |
| register HODMAEN { |
| address 0x07A |
| access_mode RW |
| modes M_SCSI |
| } |
| |
| /* |
| * Scatter/Gather Host Address |
| */ |
| register SGHADDR { |
| address 0x07C |
| access_mode RW |
| size 8 |
| modes M_DFF0, M_DFF1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCB Host Address |
| */ |
| register SCBHADDR { |
| address 0x07C |
| access_mode RW |
| size 8 |
| modes M_CCHAN |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Scatter/Gather Host Count |
| */ |
| register SGHCNT { |
| address 0x084 |
| access_mode RW |
| modes M_DFF0, M_DFF1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCB Host Count |
| */ |
| register SCBHCNT { |
| address 0x084 |
| access_mode RW |
| modes M_CCHAN |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Data FIFO Threshold |
| */ |
| register DFF_THRSH { |
| address 0x088 |
| access_mode RW |
| modes M_CFG |
| count 1 |
| field WR_DFTHRSH 0x70 { |
| WR_DFTHRSH_MIN, |
| WR_DFTHRSH_25, |
| WR_DFTHRSH_50, |
| WR_DFTHRSH_63, |
| WR_DFTHRSH_75, |
| WR_DFTHRSH_85, |
| WR_DFTHRSH_90, |
| WR_DFTHRSH_MAX |
| } |
| field RD_DFTHRSH 0x07 { |
| RD_DFTHRSH_MIN, |
| RD_DFTHRSH_25, |
| RD_DFTHRSH_50, |
| RD_DFTHRSH_63, |
| RD_DFTHRSH_75, |
| RD_DFTHRSH_85, |
| RD_DFTHRSH_90, |
| RD_DFTHRSH_MAX |
| } |
| dont_generate_debug_code |
| } |
| |
| /* |
| * ROM Address |
| */ |
| register ROMADDR { |
| address 0x08A |
| access_mode RW |
| size 3 |
| } |
| |
| /* |
| * ROM Control |
| */ |
| register ROMCNTRL { |
| address 0x08D |
| access_mode RW |
| field ROMOP 0xE0 |
| field ROMSPD 0x18 |
| field REPEAT 0x02 |
| field RDY 0x01 |
| } |
| |
| /* |
| * ROM Data |
| */ |
| register ROMDATA { |
| address 0x08E |
| access_mode RW |
| } |
| |
| /* |
| * Data Channel Receive Message 0 |
| */ |
| register DCHRXMSG0 { |
| address 0x090 |
| access_mode RO |
| modes M_DFF0, M_DFF1 |
| field CDNUM 0xF8 |
| field CFNUM 0x07 |
| } |
| |
| /* |
| * CMC Receive Message 0 |
| */ |
| register CMCRXMSG0 { |
| address 0x090 |
| access_mode RO |
| modes M_CCHAN |
| field CDNUM 0xF8 |
| field CFNUM 0x07 |
| } |
| |
| /* |
| * Overlay Receive Message 0 |
| */ |
| register OVLYRXMSG0 { |
| address 0x090 |
| access_mode RO |
| modes M_SCSI |
| field CDNUM 0xF8 |
| field CFNUM 0x07 |
| } |
| |
| /* |
| * Relaxed Order Enable |
| */ |
| register ROENABLE { |
| address 0x090 |
| access_mode RW |
| modes M_CFG |
| field MSIROEN 0x20 |
| field OVLYROEN 0x10 |
| field CMCROEN 0x08 |
| field SGROEN 0x04 |
| field DCH1ROEN 0x02 |
| field DCH0ROEN 0x01 |
| } |
| |
| /* |
| * Data Channel Receive Message 1 |
| */ |
| register DCHRXMSG1 { |
| address 0x091 |
| access_mode RO |
| modes M_DFF0, M_DFF1 |
| field CBNUM 0xFF |
| } |
| |
| /* |
| * CMC Receive Message 1 |
| */ |
| register CMCRXMSG1 { |
| address 0x091 |
| access_mode RO |
| modes M_CCHAN |
| field CBNUM 0xFF |
| } |
| |
| /* |
| * Overlay Receive Message 1 |
| */ |
| register OVLYRXMSG1 { |
| address 0x091 |
| access_mode RO |
| modes M_SCSI |
| field CBNUM 0xFF |
| } |
| |
| /* |
| * No Snoop Enable |
| */ |
| register NSENABLE { |
| address 0x091 |
| access_mode RW |
| modes M_CFG |
| field MSINSEN 0x20 |
| field OVLYNSEN 0x10 |
| field CMCNSEN 0x08 |
| field SGNSEN 0x04 |
| field DCH1NSEN 0x02 |
| field DCH0NSEN 0x01 |
| } |
| |
| /* |
| * Data Channel Receive Message 2 |
| */ |
| register DCHRXMSG2 { |
| address 0x092 |
| access_mode RO |
| modes M_DFF0, M_DFF1 |
| field MINDEX 0xFF |
| } |
| |
| /* |
| * CMC Receive Message 2 |
| */ |
| register CMCRXMSG2 { |
| address 0x092 |
| access_mode RO |
| modes M_CCHAN |
| field MINDEX 0xFF |
| } |
| |
| /* |
| * Overlay Receive Message 2 |
| */ |
| register OVLYRXMSG2 { |
| address 0x092 |
| access_mode RO |
| modes M_SCSI |
| field MINDEX 0xFF |
| } |
| |
| /* |
| * Outstanding Split Transactions |
| */ |
| register OST { |
| address 0x092 |
| access_mode RW |
| modes M_CFG |
| } |
| |
| /* |
| * Data Channel Receive Message 3 |
| */ |
| register DCHRXMSG3 { |
| address 0x093 |
| access_mode RO |
| modes M_DFF0, M_DFF1 |
| field MCLASS 0x0F |
| } |
| |
| /* |
| * CMC Receive Message 3 |
| */ |
| register CMCRXMSG3 { |
| address 0x093 |
| access_mode RO |
| modes M_CCHAN |
| field MCLASS 0x0F |
| } |
| |
| /* |
| * Overlay Receive Message 3 |
| */ |
| register OVLYRXMSG3 { |
| address 0x093 |
| access_mode RO |
| modes M_SCSI |
| field MCLASS 0x0F |
| } |
| |
| /* |
| * PCI-X Control |
| */ |
| register PCIXCTL { |
| address 0x093 |
| access_mode RW |
| modes M_CFG |
| count 1 |
| field SERRPULSE 0x80 |
| field UNEXPSCIEN 0x20 |
| field SPLTSMADIS 0x10 |
| field SPLTSTADIS 0x08 |
| field SRSPDPEEN 0x04 |
| field TSCSERREN 0x02 |
| field CMPABCDIS 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * CMC Sequencer Byte Count |
| */ |
| register CMCSEQBCNT { |
| address 0x094 |
| access_mode RO |
| modes M_CCHAN |
| } |
| |
| /* |
| * Overlay Sequencer Byte Count |
| */ |
| register OVLYSEQBCNT { |
| address 0x094 |
| access_mode RO |
| modes M_SCSI |
| } |
| |
| /* |
| * Data Channel Sequencer Byte Count |
| */ |
| register DCHSEQBCNT { |
| address 0x094 |
| access_mode RO |
| size 2 |
| modes M_DFF0, M_DFF1 |
| } |
| |
| /* |
| * Data Channel Split Status 0 |
| */ |
| register DCHSPLTSTAT0 { |
| address 0x096 |
| access_mode RW |
| modes M_DFF0, M_DFF1 |
| count 2 |
| field STAETERM 0x80 |
| field SCBCERR 0x40 |
| field SCADERR 0x20 |
| field SCDATBUCKET 0x10 |
| field CNTNOTCMPLT 0x08 |
| field RXOVRUN 0x04 |
| field RXSCEMSG 0x02 |
| field RXSPLTRSP 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * CMC Split Status 0 |
| */ |
| register CMCSPLTSTAT0 { |
| address 0x096 |
| access_mode RW |
| modes M_CCHAN |
| field STAETERM 0x80 |
| field SCBCERR 0x40 |
| field SCADERR 0x20 |
| field SCDATBUCKET 0x10 |
| field CNTNOTCMPLT 0x08 |
| field RXOVRUN 0x04 |
| field RXSCEMSG 0x02 |
| field RXSPLTRSP 0x01 |
| } |
| |
| /* |
| * Overlay Split Status 0 |
| */ |
| register OVLYSPLTSTAT0 { |
| address 0x096 |
| access_mode RW |
| modes M_SCSI |
| field STAETERM 0x80 |
| field SCBCERR 0x40 |
| field SCADERR 0x20 |
| field SCDATBUCKET 0x10 |
| field CNTNOTCMPLT 0x08 |
| field RXOVRUN 0x04 |
| field RXSCEMSG 0x02 |
| field RXSPLTRSP 0x01 |
| } |
| |
| /* |
| * Data Channel Split Status 1 |
| */ |
| register DCHSPLTSTAT1 { |
| address 0x097 |
| access_mode RW |
| modes M_DFF0, M_DFF1 |
| count 2 |
| field RXDATABUCKET 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * CMC Split Status 1 |
| */ |
| register CMCSPLTSTAT1 { |
| address 0x097 |
| access_mode RW |
| modes M_CCHAN |
| field RXDATABUCKET 0x01 |
| } |
| |
| /* |
| * Overlay Split Status 1 |
| */ |
| register OVLYSPLTSTAT1 { |
| address 0x097 |
| access_mode RW |
| modes M_SCSI |
| field RXDATABUCKET 0x01 |
| } |
| |
| /* |
| * S/G Receive Message 0 |
| */ |
| register SGRXMSG0 { |
| address 0x098 |
| access_mode RO |
| modes M_DFF0, M_DFF1 |
| field CDNUM 0xF8 |
| field CFNUM 0x07 |
| } |
| |
| /* |
| * S/G Receive Message 1 |
| */ |
| register SGRXMSG1 { |
| address 0x099 |
| access_mode RO |
| modes M_DFF0, M_DFF1 |
| field CBNUM 0xFF |
| } |
| |
| /* |
| * S/G Receive Message 2 |
| */ |
| register SGRXMSG2 { |
| address 0x09A |
| access_mode RO |
| modes M_DFF0, M_DFF1 |
| field MINDEX 0xFF |
| } |
| |
| /* |
| * S/G Receive Message 3 |
| */ |
| register SGRXMSG3 { |
| address 0x09B |
| access_mode RO |
| modes M_DFF0, M_DFF1 |
| field MCLASS 0x0F |
| } |
| |
| /* |
| * Slave Split Out Address 0 |
| */ |
| register SLVSPLTOUTADR0 { |
| address 0x098 |
| access_mode RO |
| modes M_SCSI |
| field LOWER_ADDR 0x7F |
| } |
| |
| /* |
| * Slave Split Out Address 1 |
| */ |
| register SLVSPLTOUTADR1 { |
| address 0x099 |
| access_mode RO |
| modes M_SCSI |
| field REQ_DNUM 0xF8 |
| field REQ_FNUM 0x07 |
| } |
| |
| /* |
| * Slave Split Out Address 2 |
| */ |
| register SLVSPLTOUTADR2 { |
| address 0x09A |
| access_mode RO |
| modes M_SCSI |
| field REQ_BNUM 0xFF |
| } |
| |
| /* |
| * Slave Split Out Address 3 |
| */ |
| register SLVSPLTOUTADR3 { |
| address 0x09B |
| access_mode RO |
| modes M_SCSI |
| field RLXORD 020 |
| field TAG_NUM 0x1F |
| } |
| |
| /* |
| * SG Sequencer Byte Count |
| */ |
| register SGSEQBCNT { |
| address 0x09C |
| access_mode RO |
| modes M_DFF0, M_DFF1 |
| } |
| |
| /* |
| * Slave Split Out Attribute 0 |
| */ |
| register SLVSPLTOUTATTR0 { |
| address 0x09C |
| access_mode RO |
| modes M_SCSI |
| field LOWER_BCNT 0xFF |
| } |
| |
| /* |
| * Slave Split Out Attribute 1 |
| */ |
| register SLVSPLTOUTATTR1 { |
| address 0x09D |
| access_mode RO |
| modes M_SCSI |
| field CMPLT_DNUM 0xF8 |
| field CMPLT_FNUM 0x07 |
| } |
| |
| /* |
| * Slave Split Out Attribute 2 |
| */ |
| register SLVSPLTOUTATTR2 { |
| address 0x09E |
| access_mode RO |
| size 2 |
| modes M_SCSI |
| field CMPLT_BNUM 0xFF |
| } |
| /* |
| * S/G Split Status 0 |
| */ |
| register SGSPLTSTAT0 { |
| address 0x09E |
| access_mode RW |
| modes M_DFF0, M_DFF1 |
| count 2 |
| field STAETERM 0x80 |
| field SCBCERR 0x40 |
| field SCADERR 0x20 |
| field SCDATBUCKET 0x10 |
| field CNTNOTCMPLT 0x08 |
| field RXOVRUN 0x04 |
| field RXSCEMSG 0x02 |
| field RXSPLTRSP 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * S/G Split Status 1 |
| */ |
| register SGSPLTSTAT1 { |
| address 0x09F |
| access_mode RW |
| modes M_DFF0, M_DFF1 |
| count 2 |
| field RXDATABUCKET 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Special Function |
| */ |
| register SFUNCT { |
| address 0x09f |
| access_mode RW |
| modes M_CFG |
| field TEST_GROUP 0xF0 |
| field TEST_NUM 0x0F |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Data FIFO 0 PCI Status |
| */ |
| register DF0PCISTAT { |
| address 0x0A0 |
| access_mode RW |
| modes M_CFG |
| count 1 |
| field DPE 0x80 |
| field SSE 0x40 |
| field RMA 0x20 |
| field RTA 0x10 |
| field SCAAPERR 0x08 |
| field RDPERR 0x04 |
| field TWATERR 0x02 |
| field DPR 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Data FIFO 1 PCI Status |
| */ |
| register DF1PCISTAT { |
| address 0x0A1 |
| access_mode RW |
| modes M_CFG |
| field DPE 0x80 |
| field SSE 0x40 |
| field RMA 0x20 |
| field RTA 0x10 |
| field SCAAPERR 0x08 |
| field RDPERR 0x04 |
| field TWATERR 0x02 |
| field DPR 0x01 |
| } |
| |
| /* |
| * S/G PCI Status |
| */ |
| register SGPCISTAT { |
| address 0x0A2 |
| access_mode RW |
| modes M_CFG |
| field DPE 0x80 |
| field SSE 0x40 |
| field RMA 0x20 |
| field RTA 0x10 |
| field SCAAPERR 0x08 |
| field RDPERR 0x04 |
| field DPR 0x01 |
| } |
| |
| /* |
| * CMC PCI Status |
| */ |
| register CMCPCISTAT { |
| address 0x0A3 |
| access_mode RW |
| modes M_CFG |
| field DPE 0x80 |
| field SSE 0x40 |
| field RMA 0x20 |
| field RTA 0x10 |
| field SCAAPERR 0x08 |
| field RDPERR 0x04 |
| field TWATERR 0x02 |
| field DPR 0x01 |
| } |
| |
| /* |
| * Overlay PCI Status |
| */ |
| register OVLYPCISTAT { |
| address 0x0A4 |
| access_mode RW |
| modes M_CFG |
| field DPE 0x80 |
| field SSE 0x40 |
| field RMA 0x20 |
| field RTA 0x10 |
| field SCAAPERR 0x08 |
| field RDPERR 0x04 |
| field DPR 0x01 |
| } |
| |
| /* |
| * PCI Status for MSI Master DMA Transfer |
| */ |
| register MSIPCISTAT { |
| address 0x0A6 |
| access_mode RW |
| modes M_CFG |
| field SSE 0x40 |
| field RMA 0x20 |
| field RTA 0x10 |
| field CLRPENDMSI 0x08 |
| field TWATERR 0x02 |
| field DPR 0x01 |
| } |
| |
| /* |
| * PCI Status for Target |
| */ |
| register TARGPCISTAT { |
| address 0x0A7 |
| access_mode RW |
| modes M_CFG |
| count 5 |
| field DPE 0x80 |
| field SSE 0x40 |
| field STA 0x08 |
| field TWATERR 0x02 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * LQ Packet In |
| * The last LQ Packet received |
| */ |
| register LQIN { |
| address 0x020 |
| access_mode RW |
| size 20 |
| count 2 |
| modes M_DFF0, M_DFF1, M_SCSI |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCB Type Pointer |
| * SCB offset for Target Mode SCB type information |
| */ |
| register TYPEPTR { |
| address 0x020 |
| access_mode RW |
| modes M_CFG |
| } |
| |
| /* |
| * Queue Tag Pointer |
| * SCB offset to the Two Byte tag identifier used for target mode. |
| */ |
| register TAGPTR { |
| address 0x021 |
| access_mode RW |
| modes M_CFG |
| } |
| |
| /* |
| * Logical Unit Number Pointer |
| * SCB offset to the LSB (little endian) of the lun field. |
| */ |
| register LUNPTR { |
| address 0x022 |
| access_mode RW |
| modes M_CFG |
| count 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Data Length Pointer |
| * SCB offset for the 4 byte data length field in target mode. |
| */ |
| register DATALENPTR { |
| address 0x023 |
| access_mode RW |
| modes M_CFG |
| } |
| |
| /* |
| * Status Length Pointer |
| * SCB offset to the two byte status field in target SCBs. |
| */ |
| register STATLENPTR { |
| address 0x024 |
| access_mode RW |
| modes M_CFG |
| } |
| |
| /* |
| * Command Length Pointer |
| * Scb offset for the CDB length field in initiator SCBs. |
| */ |
| register CMDLENPTR { |
| address 0x025 |
| access_mode RW |
| modes M_CFG |
| count 1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Task Attribute Pointer |
| * Scb offset for the byte field specifying the attribute byte |
| * to be used in command packets. |
| */ |
| register ATTRPTR { |
| address 0x026 |
| access_mode RW |
| modes M_CFG |
| count 1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Task Management Flags Pointer |
| * Scb offset for the byte field specifying the attribute flags |
| * byte to be used in command packets. |
| */ |
| register FLAGPTR { |
| address 0x027 |
| access_mode RW |
| modes M_CFG |
| count 1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Command Pointer |
| * Scb offset for the first byte in the CDB for initiator SCBs. |
| */ |
| register CMDPTR { |
| address 0x028 |
| access_mode RW |
| modes M_CFG |
| count 1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Queue Next Pointer |
| * Scb offset for the 2 byte "next scb link". |
| */ |
| register QNEXTPTR { |
| address 0x029 |
| access_mode RW |
| modes M_CFG |
| count 1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI ID Pointer |
| * Scb offset to the value to place in the SCSIID register |
| * during target mode connections. |
| */ |
| register IDPTR { |
| address 0x02A |
| access_mode RW |
| modes M_CFG |
| } |
| |
| /* |
| * Command Aborted Byte Pointer |
| * Offset to the SCB flags field that includes the |
| * "SCB aborted" status bit. |
| */ |
| register ABRTBYTEPTR { |
| address 0x02B |
| access_mode RW |
| modes M_CFG |
| count 1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Command Aborted Bit Pointer |
| * Bit offset in the SCB flags field for "SCB aborted" status. |
| */ |
| register ABRTBITPTR { |
| address 0x02C |
| access_mode RW |
| modes M_CFG |
| count 1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Rev B or greater. |
| */ |
| register MAXCMDBYTES { |
| address 0x02D |
| access_mode RW |
| modes M_CFG |
| } |
| |
| /* |
| * Rev B or greater. |
| */ |
| register MAXCMD2RCV { |
| address 0x02E |
| access_mode RW |
| modes M_CFG |
| } |
| |
| /* |
| * Rev B or greater. |
| */ |
| register SHORTTHRESH { |
| address 0x02F |
| access_mode RW |
| modes M_CFG |
| } |
| |
| /* |
| * Logical Unit Number Length |
| * The length, in bytes, of the SCB lun field. |
| */ |
| register LUNLEN { |
| address 0x030 |
| access_mode RW |
| modes M_CFG |
| count 2 |
| mask ILUNLEN 0x0F |
| mask TLUNLEN 0xF0 |
| dont_generate_debug_code |
| } |
| const LUNLEN_SINGLE_LEVEL_LUN 0xF |
| |
| /* |
| * CDB Limit |
| * The size, in bytes, of the embedded CDB field in initator SCBs. |
| */ |
| register CDBLIMIT { |
| address 0x031 |
| access_mode RW |
| modes M_CFG |
| count 1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Maximum Commands |
| * The maximum number of commands to issue during a |
| * single packetized connection. |
| */ |
| register MAXCMD { |
| address 0x032 |
| access_mode RW |
| modes M_CFG |
| count 9 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Maximum Command Counter |
| * The number of commands already sent during this connection |
| */ |
| register MAXCMDCNT { |
| address 0x033 |
| access_mode RW |
| modes M_CFG |
| dont_generate_debug_code |
| } |
| |
| /* |
| * LQ Packet Reserved Bytes |
| * The bytes to be sent in the currently reserved fileds |
| * of all LQ packets. |
| */ |
| register LQRSVD01 { |
| address 0x034 |
| access_mode RW |
| modes M_SCSI |
| } |
| register LQRSVD16 { |
| address 0x035 |
| access_mode RW |
| modes M_SCSI |
| } |
| register LQRSVD17 { |
| address 0x036 |
| access_mode RW |
| modes M_SCSI |
| } |
| |
| /* |
| * Command Reserved 0 |
| * The byte to be sent for the reserved byte 0 of |
| * outgoing command packets. |
| */ |
| register CMDRSVD0 { |
| address 0x037 |
| access_mode RW |
| modes M_CFG |
| } |
| |
| /* |
| * LQ Manager Control 0 |
| */ |
| register LQCTL0 { |
| address 0x038 |
| access_mode RW |
| modes M_CFG |
| field LQITARGCLT 0xC0 |
| field LQIINITGCLT 0x30 |
| field LQ0TARGCLT 0x0C |
| field LQ0INITGCLT 0x03 |
| } |
| |
| /* |
| * LQ Manager Control 1 |
| */ |
| register LQCTL1 { |
| address 0x038 |
| access_mode RW |
| modes M_DFF0, M_DFF1, M_SCSI |
| count 2 |
| field PCI2PCI 0x04 |
| field SINGLECMD 0x02 |
| field ABORTPENDING 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * LQ Manager Control 2 |
| */ |
| register LQCTL2 { |
| address 0x039 |
| access_mode RW |
| modes M_DFF0, M_DFF1, M_SCSI |
| count 5 |
| field LQIRETRY 0x80 |
| field LQICONTINUE 0x40 |
| field LQITOIDLE 0x20 |
| field LQIPAUSE 0x10 |
| field LQORETRY 0x08 |
| field LQOCONTINUE 0x04 |
| field LQOTOIDLE 0x02 |
| field LQOPAUSE 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI RAM BIST0 |
| */ |
| register SCSBIST0 { |
| address 0x039 |
| access_mode RW |
| modes M_CFG |
| field GSBISTERR 0x40 |
| field GSBISTDONE 0x20 |
| field GSBISTRUN 0x10 |
| field OSBISTERR 0x04 |
| field OSBISTDONE 0x02 |
| field OSBISTRUN 0x01 |
| } |
| |
| /* |
| * SCSI Sequence Control0 |
| */ |
| register SCSISEQ0 { |
| address 0x03A |
| access_mode RW |
| modes M_DFF0, M_DFF1, M_SCSI |
| field TEMODEO 0x80 |
| field ENSELO 0x40 |
| field ENARBO 0x20 |
| field FORCEBUSFREE 0x10 |
| field SCSIRSTO 0x01 |
| } |
| |
| /* |
| * SCSI RAM BIST 1 |
| */ |
| register SCSBIST1 { |
| address 0x03A |
| access_mode RW |
| modes M_CFG |
| field NTBISTERR 0x04 |
| field NTBISTDONE 0x02 |
| field NTBISTRUN 0x01 |
| } |
| |
| /* |
| * SCSI Sequence Control 1 |
| */ |
| register SCSISEQ1 { |
| address 0x03B |
| access_mode RW |
| modes M_DFF0, M_DFF1, M_SCSI |
| count 8 |
| field MANUALCTL 0x40 |
| field ENSELI 0x20 |
| field ENRSELI 0x10 |
| field MANUALP 0x0C |
| field ENAUTOATNP 0x02 |
| field ALTSTIM 0x01 |
| } |
| |
| /* |
| * SCSI Transfer Control 0 |
| */ |
| register SXFRCTL0 { |
| address 0x03C |
| access_mode RW |
| modes M_SCSI |
| field DFON 0x80 |
| field DFPEXP 0x40 |
| field BIOSCANCELEN 0x10 |
| field SPIOEN 0x08 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Transfer Control 1 |
| */ |
| register SXFRCTL1 { |
| address 0x03D |
| access_mode RW |
| modes M_SCSI |
| field BITBUCKET 0x80 |
| field ENSACHK 0x40 |
| field ENSPCHK 0x20 |
| field STIMESEL 0x18 |
| field ENSTIMER 0x04 |
| field ACTNEGEN 0x02 |
| field STPWEN 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Transfer Control 2 |
| */ |
| register SXFRCTL2 { |
| address 0x03E |
| access_mode RW |
| modes M_SCSI |
| field AUTORSTDIS 0x10 |
| field CMDDMAEN 0x08 |
| field ASU 0x07 |
| } |
| |
| /* |
| * SCSI Bus Initiator IDs |
| * Bitmask of observed initiators on the bus. |
| */ |
| register BUSINITID { |
| address 0x03C |
| access_mode RW |
| modes M_CFG |
| size 2 |
| } |
| |
| /* |
| * Data Length Counters |
| * Packet byte counter. |
| */ |
| register DLCOUNT { |
| address 0x03C |
| access_mode RW |
| modes M_DFF0, M_DFF1 |
| size 3 |
| } |
| |
| /* |
| * Data FIFO Status |
| */ |
| register DFFSTAT { |
| address 0x03F |
| access_mode RW |
| modes M_SCSI |
| field FIFO1FREE 0x20 |
| field FIFO0FREE 0x10 |
| /* |
| * On the B, this enum only works |
| * in the read direction. For writes, |
| * you must use the B version of the |
| * CURRFIFO_0 definition which is defined |
| * as a constant outside of this register |
| * definition to avoid confusing the |
| * register pretty printing code. |
| */ |
| enum CURRFIFO 0x03 { |
| CURRFIFO_0, |
| CURRFIFO_1, |
| CURRFIFO_NONE 0x3 |
| } |
| } |
| |
| const B_CURRFIFO_0 0x2 |
| |
| /* |
| * SCSI Bus Target IDs |
| * Bitmask of observed targets on the bus. |
| */ |
| register BUSTARGID { |
| address 0x03E |
| access_mode RW |
| modes M_CFG |
| size 2 |
| } |
| |
| /* |
| * SCSI Control Signal Out |
| */ |
| register SCSISIGO { |
| address 0x040 |
| access_mode RW |
| modes M_DFF0, M_DFF1, M_SCSI |
| field CDO 0x80 |
| field IOO 0x40 |
| field MSGO 0x20 |
| field ATNO 0x10 |
| field SELO 0x08 |
| field BSYO 0x04 |
| field REQO 0x02 |
| field ACKO 0x01 |
| /* |
| * Possible phases to write into SCSISIG0 |
| */ |
| enum PHASE_MASK CDO|IOO|MSGO { |
| P_DATAOUT 0x0, |
| P_DATAIN IOO, |
| P_DATAOUT_DT P_DATAOUT|MSGO, |
| P_DATAIN_DT P_DATAIN|MSGO, |
| P_COMMAND CDO, |
| P_MESGOUT CDO|MSGO, |
| P_STATUS CDO|IOO, |
| P_MESGIN CDO|IOO|MSGO |
| } |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Control Signal In |
| */ |
| register SCSISIGI { |
| address 0x041 |
| access_mode RO |
| modes M_DFF0, M_DFF1, M_SCSI |
| field CDI 0x80 |
| field IOI 0x40 |
| field MSGI 0x20 |
| field ATNI 0x10 |
| field SELI 0x08 |
| field BSYI 0x04 |
| field REQI 0x02 |
| field ACKI 0x01 |
| /* |
| * Possible phases in SCSISIGI |
| */ |
| enum PHASE_MASK CDO|IOO|MSGO { |
| P_DATAOUT 0x0, |
| P_DATAIN IOO, |
| P_DATAOUT_DT P_DATAOUT|MSGO, |
| P_DATAIN_DT P_DATAIN|MSGO, |
| P_COMMAND CDO, |
| P_MESGOUT CDO|MSGO, |
| P_STATUS CDO|IOO, |
| P_MESGIN CDO|IOO|MSGO |
| } |
| } |
| |
| /* |
| * Multiple Target IDs |
| * Bitmask of ids to respond as a target. |
| */ |
| register MULTARGID { |
| address 0x040 |
| access_mode RW |
| modes M_CFG |
| size 2 |
| count 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Phase |
| */ |
| register SCSIPHASE { |
| address 0x042 |
| access_mode RO |
| modes M_DFF0, M_DFF1, M_SCSI |
| field STATUS_PHASE 0x20 |
| field COMMAND_PHASE 0x10 |
| field MSG_IN_PHASE 0x08 |
| field MSG_OUT_PHASE 0x04 |
| field DATA_PHASE_MASK 0x03 { |
| DATA_OUT_PHASE 0x01, |
| DATA_IN_PHASE 0x02 |
| } |
| } |
| |
| /* |
| * SCSI Data 0 Image |
| */ |
| register SCSIDAT0_IMG { |
| address 0x043 |
| access_mode RW |
| modes M_DFF0, M_DFF1, M_SCSI |
| } |
| |
| /* |
| * SCSI Latched Data |
| */ |
| register SCSIDAT { |
| address 0x044 |
| access_mode RW |
| modes M_DFF0, M_DFF1, M_SCSI |
| size 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Data Bus |
| */ |
| register SCSIBUS { |
| address 0x046 |
| access_mode RW |
| modes M_DFF0, M_DFF1, M_SCSI |
| size 2 |
| } |
| |
| /* |
| * Target ID In |
| */ |
| register TARGIDIN { |
| address 0x048 |
| access_mode RO |
| modes M_DFF0, M_DFF1, M_SCSI |
| count 2 |
| field CLKOUT 0x80 |
| field TARGID 0x0F |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Selection/Reselection ID |
| * Upper four bits are the device id. The ONEBIT is set when the re/selecting |
| * device did not set its own ID. |
| */ |
| register SELID { |
| address 0x049 |
| access_mode RW |
| modes M_DFF0, M_DFF1, M_SCSI |
| field SELID_MASK 0xf0 |
| field ONEBIT 0x08 |
| } |
| |
| /* |
| * SCSI Block Control |
| * Controls Bus type and channel selection. SELWIDE allows for the |
| * coexistence of 8bit and 16bit devices on a wide bus. |
| */ |
| register SBLKCTL { |
| address 0x04A |
| access_mode RW |
| modes M_DFF0, M_DFF1, M_SCSI |
| field DIAGLEDEN 0x80 |
| field DIAGLEDON 0x40 |
| field ENAB40 0x08 /* LVD transceiver active */ |
| field ENAB20 0x04 /* SE/HVD transceiver active */ |
| field SELWIDE 0x02 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Option Mode |
| */ |
| register OPTIONMODE { |
| address 0x04A |
| access_mode RW |
| modes M_CFG |
| count 4 |
| field BIOSCANCTL 0x80 |
| field AUTOACKEN 0x40 |
| field BIASCANCTL 0x20 |
| field BUSFREEREV 0x10 |
| field ENDGFORMCHK 0x04 |
| field AUTO_MSGOUT_DE 0x02 |
| mask OPTIONMODE_DEFAULTS AUTO_MSGOUT_DE |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Status 0 |
| */ |
| register SSTAT0 { |
| address 0x04B |
| access_mode RO |
| modes M_DFF0, M_DFF1, M_SCSI |
| field TARGET 0x80 /* Board acting as target */ |
| field SELDO 0x40 /* Selection Done */ |
| field SELDI 0x20 /* Board has been selected */ |
| field SELINGO 0x10 /* Selection In Progress */ |
| field IOERR 0x08 /* LVD Tranceiver mode changed */ |
| field OVERRUN 0x04 /* SCSI Offset overrun detected */ |
| field SPIORDY 0x02 /* SCSI PIO Ready */ |
| field ARBDO 0x01 /* Arbitration Done Out */ |
| } |
| |
| /* |
| * Clear SCSI Interrupt 0 |
| * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT0. |
| */ |
| register CLRSINT0 { |
| address 0x04B |
| access_mode WO |
| modes M_DFF0, M_DFF1, M_SCSI |
| field CLRSELDO 0x40 |
| field CLRSELDI 0x20 |
| field CLRSELINGO 0x10 |
| field CLRIOERR 0x08 |
| field CLROVERRUN 0x04 |
| field CLRSPIORDY 0x02 |
| field CLRARBDO 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Interrupt Mode 0 |
| * Setting any bit will enable the corresponding function |
| * in SIMODE0 to interrupt via the IRQ pin. |
| */ |
| register SIMODE0 { |
| address 0x04B |
| access_mode RW |
| modes M_CFG |
| count 8 |
| field ENSELDO 0x40 |
| field ENSELDI 0x20 |
| field ENSELINGO 0x10 |
| field ENIOERR 0x08 |
| field ENOVERRUN 0x04 |
| field ENSPIORDY 0x02 |
| field ENARBDO 0x01 |
| } |
| |
| /* |
| * SCSI Status 1 |
| */ |
| register SSTAT1 { |
| address 0x04C |
| access_mode RO |
| modes M_DFF0, M_DFF1, M_SCSI |
| field SELTO 0x80 |
| field ATNTARG 0x40 |
| field SCSIRSTI 0x20 |
| field PHASEMIS 0x10 |
| field BUSFREE 0x08 |
| field SCSIPERR 0x04 |
| field STRB2FAST 0x02 |
| field REQINIT 0x01 |
| } |
| |
| /* |
| * Clear SCSI Interrupt 1 |
| * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT1. |
| */ |
| register CLRSINT1 { |
| address 0x04C |
| access_mode WO |
| modes M_DFF0, M_DFF1, M_SCSI |
| field CLRSELTIMEO 0x80 |
| field CLRATNO 0x40 |
| field CLRSCSIRSTI 0x20 |
| field CLRBUSFREE 0x08 |
| field CLRSCSIPERR 0x04 |
| field CLRSTRB2FAST 0x02 |
| field CLRREQINIT 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Status 2 |
| */ |
| register SSTAT2 { |
| address 0x04d |
| access_mode RO |
| modes M_DFF0, M_DFF1, M_SCSI |
| field BUSFREETIME 0xc0 { |
| BUSFREE_LQO 0x40, |
| BUSFREE_DFF0 0x80, |
| BUSFREE_DFF1 0xC0 |
| } |
| field NONPACKREQ 0x20 |
| field EXP_ACTIVE 0x10 /* SCSI Expander Active */ |
| field BSYX 0x08 /* Busy Expander */ |
| field WIDE_RES 0x04 /* Modes 0 and 1 only */ |
| field SDONE 0x02 /* Modes 0 and 1 only */ |
| field DMADONE 0x01 /* Modes 0 and 1 only */ |
| } |
| |
| /* |
| * Clear SCSI Interrupt 2 |
| */ |
| register CLRSINT2 { |
| address 0x04D |
| access_mode WO |
| modes M_DFF0, M_DFF1, M_SCSI |
| field CLRNONPACKREQ 0x20 |
| field CLRWIDE_RES 0x04 /* Modes 0 and 1 only */ |
| field CLRSDONE 0x02 /* Modes 0 and 1 only */ |
| field CLRDMADONE 0x01 /* Modes 0 and 1 only */ |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Interrupt Mode 2 |
| */ |
| register SIMODE2 { |
| address 0x04D |
| access_mode RW |
| modes M_CFG |
| field ENWIDE_RES 0x04 |
| field ENSDONE 0x02 |
| field ENDMADONE 0x01 |
| } |
| |
| /* |
| * Physical Error Diagnosis |
| */ |
| register PERRDIAG { |
| address 0x04E |
| access_mode RO |
| modes M_DFF0, M_DFF1, M_SCSI |
| count 3 |
| field HIZERO 0x80 |
| field HIPERR 0x40 |
| field PREVPHASE 0x20 |
| field PARITYERR 0x10 |
| field AIPERR 0x08 |
| field CRCERR 0x04 |
| field DGFORMERR 0x02 |
| field DTERR 0x01 |
| } |
| |
| /* |
| * LQI Manager Current State |
| */ |
| register LQISTATE { |
| address 0x04E |
| access_mode RO |
| modes M_CFG |
| count 6 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Offset Count |
| */ |
| register SOFFCNT { |
| address 0x04F |
| access_mode RO |
| modes M_DFF0, M_DFF1, M_SCSI |
| count 1 |
| } |
| |
| /* |
| * LQO Manager Current State |
| */ |
| register LQOSTATE { |
| address 0x04F |
| access_mode RO |
| modes M_CFG |
| count 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * LQI Manager Status |
| */ |
| register LQISTAT0 { |
| address 0x050 |
| access_mode RO |
| modes M_DFF0, M_DFF1, M_SCSI |
| count 2 |
| field LQIATNQAS 0x20 |
| field LQICRCT1 0x10 |
| field LQICRCT2 0x08 |
| field LQIBADLQT 0x04 |
| field LQIATNLQ 0x02 |
| field LQIATNCMD 0x01 |
| } |
| |
| /* |
| * Clear LQI Interrupts 0 |
| */ |
| register CLRLQIINT0 { |
| address 0x050 |
| access_mode WO |
| modes M_DFF0, M_DFF1, M_SCSI |
| count 1 |
| field CLRLQIATNQAS 0x20 |
| field CLRLQICRCT1 0x10 |
| field CLRLQICRCT2 0x08 |
| field CLRLQIBADLQT 0x04 |
| field CLRLQIATNLQ 0x02 |
| field CLRLQIATNCMD 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * LQI Manager Interrupt Mode 0 |
| */ |
| register LQIMODE0 { |
| address 0x050 |
| access_mode RW |
| modes M_CFG |
| count 3 |
| field ENLQIATNQASK 0x20 |
| field ENLQICRCT1 0x10 |
| field ENLQICRCT2 0x08 |
| field ENLQIBADLQT 0x04 |
| field ENLQIATNLQ 0x02 |
| field ENLQIATNCMD 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * LQI Manager Status 1 |
| */ |
| register LQISTAT1 { |
| address 0x051 |
| access_mode RO |
| modes M_DFF0, M_DFF1, M_SCSI |
| count 3 |
| field LQIPHASE_LQ 0x80 |
| field LQIPHASE_NLQ 0x40 |
| field LQIABORT 0x20 |
| field LQICRCI_LQ 0x10 |
| field LQICRCI_NLQ 0x08 |
| field LQIBADLQI 0x04 |
| field LQIOVERI_LQ 0x02 |
| field LQIOVERI_NLQ 0x01 |
| } |
| |
| /* |
| * Clear LQI Manager Interrupts1 |
| */ |
| register CLRLQIINT1 { |
| address 0x051 |
| access_mode WO |
| modes M_DFF0, M_DFF1, M_SCSI |
| count 4 |
| field CLRLQIPHASE_LQ 0x80 |
| field CLRLQIPHASE_NLQ 0x40 |
| field CLRLIQABORT 0x20 |
| field CLRLQICRCI_LQ 0x10 |
| field CLRLQICRCI_NLQ 0x08 |
| field CLRLQIBADLQI 0x04 |
| field CLRLQIOVERI_LQ 0x02 |
| field CLRLQIOVERI_NLQ 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * LQI Manager Interrupt Mode 1 |
| */ |
| register LQIMODE1 { |
| address 0x051 |
| access_mode RW |
| modes M_CFG |
| count 4 |
| field ENLQIPHASE_LQ 0x80 /* LQIPHASE1 */ |
| field ENLQIPHASE_NLQ 0x40 /* LQIPHASE2 */ |
| field ENLIQABORT 0x20 |
| field ENLQICRCI_LQ 0x10 /* LQICRCI1 */ |
| field ENLQICRCI_NLQ 0x08 /* LQICRCI2 */ |
| field ENLQIBADLQI 0x04 |
| field ENLQIOVERI_LQ 0x02 /* LQIOVERI1 */ |
| field ENLQIOVERI_NLQ 0x01 /* LQIOVERI2 */ |
| dont_generate_debug_code |
| } |
| |
| /* |
| * LQI Manager Status 2 |
| */ |
| register LQISTAT2 { |
| address 0x052 |
| access_mode RO |
| modes M_DFF0, M_DFF1, M_SCSI |
| field PACKETIZED 0x80 |
| field LQIPHASE_OUTPKT 0x40 |
| field LQIWORKONLQ 0x20 |
| field LQIWAITFIFO 0x10 |
| field LQISTOPPKT 0x08 |
| field LQISTOPLQ 0x04 |
| field LQISTOPCMD 0x02 |
| field LQIGSAVAIL 0x01 |
| } |
| |
| /* |
| * SCSI Status 3 |
| */ |
| register SSTAT3 { |
| address 0x053 |
| access_mode RO |
| modes M_DFF0, M_DFF1, M_SCSI |
| count 3 |
| field NTRAMPERR 0x02 |
| field OSRAMPERR 0x01 |
| } |
| |
| /* |
| * Clear SCSI Status 3 |
| */ |
| register CLRSINT3 { |
| address 0x053 |
| access_mode WO |
| modes M_DFF0, M_DFF1, M_SCSI |
| count 3 |
| field CLRNTRAMPERR 0x02 |
| field CLROSRAMPERR 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Interrupt Mode 3 |
| */ |
| register SIMODE3 { |
| address 0x053 |
| access_mode RW |
| modes M_CFG |
| count 4 |
| field ENNTRAMPERR 0x02 |
| field ENOSRAMPERR 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * LQO Manager Status 0 |
| */ |
| register LQOSTAT0 { |
| address 0x054 |
| access_mode RO |
| modes M_DFF0, M_DFF1, M_SCSI |
| count 2 |
| field LQOTARGSCBPERR 0x10 |
| field LQOSTOPT2 0x08 |
| field LQOATNLQ 0x04 |
| field LQOATNPKT 0x02 |
| field LQOTCRC 0x01 |
| } |
| |
| /* |
| * Clear LQO Manager interrupt 0 |
| */ |
| register CLRLQOINT0 { |
| address 0x054 |
| access_mode WO |
| modes M_DFF0, M_DFF1, M_SCSI |
| count 3 |
| field CLRLQOTARGSCBPERR 0x10 |
| field CLRLQOSTOPT2 0x08 |
| field CLRLQOATNLQ 0x04 |
| field CLRLQOATNPKT 0x02 |
| field CLRLQOTCRC 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * LQO Manager Interrupt Mode 0 |
| */ |
| register LQOMODE0 { |
| address 0x054 |
| access_mode RW |
| modes M_CFG |
| count 4 |
| field ENLQOTARGSCBPERR 0x10 |
| field ENLQOSTOPT2 0x08 |
| field ENLQOATNLQ 0x04 |
| field ENLQOATNPKT 0x02 |
| field ENLQOTCRC 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * LQO Manager Status 1 |
| */ |
| register LQOSTAT1 { |
| address 0x055 |
| access_mode RO |
| modes M_DFF0, M_DFF1, M_SCSI |
| field LQOINITSCBPERR 0x10 |
| field LQOSTOPI2 0x08 |
| field LQOBADQAS 0x04 |
| field LQOBUSFREE 0x02 |
| field LQOPHACHGINPKT 0x01 |
| } |
| |
| /* |
| * Clear LOQ Interrupt 1 |
| */ |
| register CLRLQOINT1 { |
| address 0x055 |
| access_mode WO |
| modes M_DFF0, M_DFF1, M_SCSI |
| count 7 |
| field CLRLQOINITSCBPERR 0x10 |
| field CLRLQOSTOPI2 0x08 |
| field CLRLQOBADQAS 0x04 |
| field CLRLQOBUSFREE 0x02 |
| field CLRLQOPHACHGINPKT 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * LQO Manager Interrupt Mode 1 |
| */ |
| register LQOMODE1 { |
| address 0x055 |
| access_mode RW |
| modes M_CFG |
| count 4 |
| field ENLQOINITSCBPERR 0x10 |
| field ENLQOSTOPI2 0x08 |
| field ENLQOBADQAS 0x04 |
| field ENLQOBUSFREE 0x02 |
| field ENLQOPHACHGINPKT 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * LQO Manager Status 2 |
| */ |
| register LQOSTAT2 { |
| address 0x056 |
| access_mode RO |
| modes M_DFF0, M_DFF1, M_SCSI |
| field LQOPKT 0xE0 |
| field LQOWAITFIFO 0x10 |
| field LQOPHACHGOUTPKT 0x02 /* outside of packet boundaries. */ |
| field LQOSTOP0 0x01 /* Stopped after sending all packets */ |
| } |
| |
| /* |
| * Output Synchronizer Space Count |
| */ |
| register OS_SPACE_CNT { |
| address 0x056 |
| access_mode RO |
| modes M_CFG |
| count 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Interrupt Mode 1 |
| * Setting any bit will enable the corresponding function |
| * in SIMODE1 to interrupt via the IRQ pin. |
| */ |
| register SIMODE1 { |
| address 0x057 |
| access_mode RW |
| modes M_DFF0, M_DFF1, M_SCSI |
| field ENSELTIMO 0x80 |
| field ENATNTARG 0x40 |
| field ENSCSIRST 0x20 |
| field ENPHASEMIS 0x10 |
| field ENBUSFREE 0x08 |
| field ENSCSIPERR 0x04 |
| field ENSTRB2FAST 0x02 |
| field ENREQINIT 0x01 |
| } |
| |
| /* |
| * Good Status FIFO |
| */ |
| register GSFIFO { |
| address 0x058 |
| access_mode RO |
| size 2 |
| modes M_DFF0, M_DFF1, M_SCSI |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Data FIFO SCSI Transfer Control |
| */ |
| register DFFSXFRCTL { |
| address 0x05A |
| access_mode RW |
| modes M_DFF0, M_DFF1 |
| field DFFBITBUCKET 0x08 |
| field CLRSHCNT 0x04 |
| field CLRCHN 0x02 |
| field RSTCHN 0x01 |
| } |
| |
| /* |
| * Next SCSI Control Block |
| */ |
| register NEXTSCB { |
| address 0x05A |
| access_mode RW |
| size 2 |
| modes M_SCSI |
| dont_generate_debug_code |
| } |
| |
| /* |
| * LQO SCSI Control |
| * (Rev B only.) |
| */ |
| register LQOSCSCTL { |
| address 0x05A |
| access_mode RW |
| size 1 |
| modes M_CFG |
| count 1 |
| field LQOH2A_VERSION 0x80 |
| field LQOBUSETDLY 0x40 |
| field LQONOHOLDLACK 0x02 |
| field LQONOCHKOVER 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SEQ Interrupts |
| */ |
| register SEQINTSRC { |
| address 0x05B |
| access_mode RO |
| modes M_DFF0, M_DFF1 |
| field CTXTDONE 0x40 |
| field SAVEPTRS 0x20 |
| field CFG4DATA 0x10 |
| field CFG4ISTAT 0x08 |
| field CFG4TSTAT 0x04 |
| field CFG4ICMD 0x02 |
| field CFG4TCMD 0x01 |
| } |
| |
| /* |
| * Clear Arp Interrupts |
| */ |
| register CLRSEQINTSRC { |
| address 0x05B |
| access_mode WO |
| modes M_DFF0, M_DFF1 |
| field CLRCTXTDONE 0x40 |
| field CLRSAVEPTRS 0x20 |
| field CLRCFG4DATA 0x10 |
| field CLRCFG4ISTAT 0x08 |
| field CLRCFG4TSTAT 0x04 |
| field CLRCFG4ICMD 0x02 |
| field CLRCFG4TCMD 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SEQ Interrupt Enabled (Shared) |
| */ |
| register SEQIMODE { |
| address 0x05C |
| access_mode RW |
| modes M_DFF0, M_DFF1 |
| field ENCTXTDONE 0x40 |
| field ENSAVEPTRS 0x20 |
| field ENCFG4DATA 0x10 |
| field ENCFG4ISTAT 0x08 |
| field ENCFG4TSTAT 0x04 |
| field ENCFG4ICMD 0x02 |
| field ENCFG4TCMD 0x01 |
| } |
| |
| /* |
| * Current SCSI Control Block |
| */ |
| register CURRSCB { |
| address 0x05C |
| access_mode RW |
| size 2 |
| modes M_SCSI |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Data FIFO Status |
| */ |
| register MDFFSTAT { |
| address 0x05D |
| access_mode RO |
| modes M_DFF0, M_DFF1 |
| field SHCNTNEGATIVE 0x40 /* Rev B or higher */ |
| field SHCNTMINUS1 0x20 /* Rev B or higher */ |
| field LASTSDONE 0x10 |
| field SHVALID 0x08 |
| field DLZERO 0x04 /* FIFO data ends on packet boundary. */ |
| field DATAINFIFO 0x02 |
| field FIFOFREE 0x01 |
| } |
| |
| /* |
| * CRC Control |
| */ |
| register CRCCONTROL { |
| address 0x05d |
| access_mode RW |
| modes M_CFG |
| field CRCVALCHKEN 0x40 |
| } |
| |
| /* |
| * SCSI Test Control |
| */ |
| register SCSITEST { |
| address 0x05E |
| access_mode RW |
| modes M_CFG |
| field CNTRTEST 0x08 |
| field SEL_TXPLL_DEBUG 0x04 |
| } |
| |
| /* |
| * Data FIFO Queue Tag |
| */ |
| register DFFTAG { |
| address 0x05E |
| access_mode RW |
| size 2 |
| modes M_DFF0, M_DFF1 |
| } |
| |
| /* |
| * Last SCSI Control Block |
| */ |
| register LASTSCB { |
| address 0x05E |
| access_mode RW |
| size 2 |
| modes M_SCSI |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI I/O Cell Power-down Control |
| */ |
| register IOPDNCTL { |
| address 0x05F |
| access_mode RW |
| modes M_CFG |
| field DISABLE_OE 0x80 |
| field PDN_IDIST 0x04 |
| field PDN_DIFFSENSE 0x01 |
| } |
| |
| /* |
| * Shadow Host Address. |
| */ |
| register SHADDR { |
| address 0x060 |
| access_mode RO |
| size 8 |
| modes M_DFF0, M_DFF1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Data Group CRC Interval. |
| */ |
| register DGRPCRCI { |
| address 0x060 |
| access_mode RW |
| size 2 |
| modes M_CFG |
| } |
| |
| /* |
| * Data Transfer Negotiation Address |
| */ |
| register NEGOADDR { |
| address 0x060 |
| access_mode RW |
| modes M_SCSI |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Data Transfer Negotiation Data - Period Byte |
| */ |
| register NEGPERIOD { |
| address 0x061 |
| access_mode RW |
| modes M_SCSI |
| count 1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Packetized CRC Interval |
| */ |
| register PACKCRCI { |
| address 0x062 |
| access_mode RW |
| size 2 |
| modes M_CFG |
| } |
| |
| /* |
| * Data Transfer Negotiation Data - Offset Byte |
| */ |
| register NEGOFFSET { |
| address 0x062 |
| access_mode RW |
| modes M_SCSI |
| count 1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Data Transfer Negotiation Data - PPR Options |
| */ |
| register NEGPPROPTS { |
| address 0x063 |
| access_mode RW |
| modes M_SCSI |
| count 1 |
| field PPROPT_PACE 0x08 |
| field PPROPT_QAS 0x04 |
| field PPROPT_DT 0x02 |
| field PPROPT_IUT 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Data Transfer Negotiation Data - Connection Options |
| */ |
| register NEGCONOPTS { |
| address 0x064 |
| access_mode RW |
| modes M_SCSI |
| field ENSNAPSHOT 0x40 |
| field RTI_WRTDIS 0x20 |
| field RTI_OVRDTRN 0x10 |
| field ENSLOWCRC 0x08 |
| field ENAUTOATNI 0x04 |
| field ENAUTOATNO 0x02 |
| field WIDEXFER 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Negotiation Table Annex Column Index. |
| */ |
| register ANNEXCOL { |
| address 0x065 |
| access_mode RW |
| modes M_SCSI |
| count 7 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Check |
| * (Rev. B only) |
| */ |
| register SCSCHKN { |
| address 0x066 |
| access_mode RW |
| modes M_CFG |
| count 1 |
| field BIDICHKDIS 0x80 |
| field STSELSKIDDIS 0x40 |
| field CURRFIFODEF 0x20 |
| field WIDERESEN 0x10 |
| field SDONEMSKDIS 0x08 |
| field DFFACTCLR 0x04 |
| field SHVALIDSTDIS 0x02 |
| field LSTSGCLRDIS 0x01 |
| dont_generate_debug_code |
| } |
| |
| const AHD_ANNEXCOL_PER_DEV0 4 |
| const AHD_NUM_PER_DEV_ANNEXCOLS 4 |
| const AHD_ANNEXCOL_PRECOMP_SLEW 4 |
| const AHD_PRECOMP_MASK 0x07 |
| const AHD_PRECOMP_SHIFT 0 |
| const AHD_PRECOMP_CUTBACK_17 0x04 |
| const AHD_PRECOMP_CUTBACK_29 0x06 |
| const AHD_PRECOMP_CUTBACK_37 0x07 |
| const AHD_SLEWRATE_MASK 0x78 |
| const AHD_SLEWRATE_SHIFT 3 |
| /* |
| * Rev A has only a single bit (high bit of field) of slew adjustment. |
| * Rev B has 4 bits. The current default happens to be the same for both. |
| */ |
| const AHD_SLEWRATE_DEF_REVA 0x08 |
| const AHD_SLEWRATE_DEF_REVB 0x08 |
| |
| /* Rev A does not have any amplitude setting. */ |
| const AHD_ANNEXCOL_AMPLITUDE 6 |
| const AHD_AMPLITUDE_MASK 0x7 |
| const AHD_AMPLITUDE_SHIFT 0 |
| const AHD_AMPLITUDE_DEF 0x7 |
| |
| /* |
| * Negotiation Table Annex Data Port. |
| */ |
| register ANNEXDAT { |
| address 0x066 |
| access_mode RW |
| modes M_SCSI |
| count 3 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Initiator's Own Id. |
| * The SCSI ID to use for Selection Out and seen during a reselection.. |
| */ |
| register IOWNID { |
| address 0x067 |
| access_mode RW |
| modes M_SCSI |
| dont_generate_debug_code |
| } |
| |
| /* |
| * 960MHz Phase-Locked Loop Control 0 |
| */ |
| register PLL960CTL0 { |
| address 0x068 |
| access_mode RW |
| modes M_CFG |
| field PLL_VCOSEL 0x80 |
| field PLL_PWDN 0x40 |
| field PLL_NS 0x30 |
| field PLL_ENLUD 0x08 |
| field PLL_ENLPF 0x04 |
| field PLL_DLPF 0x02 |
| field PLL_ENFBM 0x01 |
| } |
| |
| /* |
| * Target Own Id |
| */ |
| register TOWNID { |
| address 0x069 |
| access_mode RW |
| modes M_SCSI |
| count 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * 960MHz Phase-Locked Loop Control 1 |
| */ |
| register PLL960CTL1 { |
| address 0x069 |
| access_mode RW |
| modes M_CFG |
| field PLL_CNTEN 0x80 |
| field PLL_CNTCLR 0x40 |
| field PLL_RST 0x01 |
| } |
| |
| /* |
| * Expander Signature |
| */ |
| register XSIG { |
| address 0x06A |
| access_mode RW |
| modes M_SCSI |
| } |
| |
| /* |
| * Shadow Byte Count |
| */ |
| register SHCNT { |
| address 0x068 |
| access_mode RW |
| size 3 |
| modes M_DFF0, M_DFF1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Selection Out ID |
| */ |
| register SELOID { |
| address 0x06B |
| access_mode RW |
| modes M_SCSI |
| } |
| |
| /* |
| * 960-MHz Phase-Locked Loop Test Count |
| */ |
| register PLL960CNT0 { |
| address 0x06A |
| access_mode RO |
| size 2 |
| modes M_CFG |
| } |
| |
| /* |
| * 400-MHz Phase-Locked Loop Control 0 |
| */ |
| register PLL400CTL0 { |
| address 0x06C |
| access_mode RW |
| modes M_CFG |
| field PLL_VCOSEL 0x80 |
| field PLL_PWDN 0x40 |
| field PLL_NS 0x30 |
| field PLL_ENLUD 0x08 |
| field PLL_ENLPF 0x04 |
| field PLL_DLPF 0x02 |
| field PLL_ENFBM 0x01 |
| } |
| |
| /* |
| * Arbitration Fairness |
| */ |
| register FAIRNESS { |
| address 0x06C |
| access_mode RW |
| size 2 |
| modes M_SCSI |
| } |
| |
| /* |
| * 400-MHz Phase-Locked Loop Control 1 |
| */ |
| register PLL400CTL1 { |
| address 0x06D |
| access_mode RW |
| modes M_CFG |
| field PLL_CNTEN 0x80 |
| field PLL_CNTCLR 0x40 |
| field PLL_RST 0x01 |
| } |
| |
| /* |
| * Arbitration Unfairness |
| */ |
| register UNFAIRNESS { |
| address 0x06E |
| access_mode RW |
| size 2 |
| modes M_SCSI |
| } |
| |
| /* |
| * 400-MHz Phase-Locked Loop Test Count |
| */ |
| register PLL400CNT0 { |
| address 0x06E |
| access_mode RO |
| size 2 |
| modes M_CFG |
| } |
| |
| /* |
| * SCB Page Pointer |
| */ |
| register SCBPTR { |
| address 0x0A8 |
| access_mode RW |
| size 2 |
| modes M_DFF0, M_DFF1, M_CCHAN, M_SCSI |
| dont_generate_debug_code |
| } |
| |
| /* |
| * CMC SCB Array Count |
| * Number of bytes to transfer between CMC SCB memory and SCBRAM. |
| * Transfers must be 8byte aligned and sized. |
| */ |
| register CCSCBACNT { |
| address 0x0AB |
| access_mode RW |
| modes M_CCHAN |
| } |
| |
| /* |
| * SCB Autopointer |
| * SCB-Next Address Snooping logic. When an SCB is transferred to |
| * the card, the next SCB address to be used by the CMC array can |
| * be autoloaded from that transfer. |
| */ |
| register SCBAUTOPTR { |
| address 0x0AB |
| access_mode RW |
| modes M_CFG |
| count 1 |
| field AUSCBPTR_EN 0x80 |
| field SCBPTR_ADDR 0x38 |
| field SCBPTR_OFF 0x07 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * CMC SG Ram Address Pointer |
| */ |
| register CCSGADDR { |
| address 0x0AC |
| access_mode RW |
| modes M_DFF0, M_DFF1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * CMC SCB RAM Address Pointer |
| */ |
| register CCSCBADDR { |
| address 0x0AC |
| access_mode RW |
| modes M_CCHAN |
| dont_generate_debug_code |
| } |
| |
| /* |
| * CMC SCB Ram Back-up Address Pointer |
| * Indicates the true stop location of transfers halted prior |
| * to SCBHCNT going to 0. |
| */ |
| register CCSCBADR_BK { |
| address 0x0AC |
| access_mode RO |
| modes M_CFG |
| } |
| |
| /* |
| * CMC SG Control |
| */ |
| register CCSGCTL { |
| address 0x0AD |
| access_mode RW |
| modes M_DFF0, M_DFF1 |
| field CCSGDONE 0x80 |
| field SG_CACHE_AVAIL 0x10 |
| field CCSGENACK 0x08 |
| mask CCSGEN 0x0C |
| field SG_FETCH_REQ 0x02 |
| field CCSGRESET 0x01 |
| } |
| |
| /* |
| * CMD SCB Control |
| */ |
| register CCSCBCTL { |
| address 0x0AD |
| access_mode RW |
| modes M_CCHAN |
| field CCSCBDONE 0x80 |
| field ARRDONE 0x40 |
| field CCARREN 0x10 |
| field CCSCBEN 0x08 |
| field CCSCBDIR 0x04 |
| field CCSCBRESET 0x01 |
| } |
| |
| /* |
| * CMC Ram BIST |
| */ |
| register CMC_RAMBIST { |
| address 0x0AD |
| access_mode RW |
| modes M_CFG |
| field SG_ELEMENT_SIZE 0x80 |
| field SCBRAMBIST_FAIL 0x40 |
| field SG_BIST_FAIL 0x20 |
| field SG_BIST_EN 0x10 |
| field CMC_BUFFER_BIST_FAIL 0x02 |
| field CMC_BUFFER_BIST_EN 0x01 |
| } |
| |
| /* |
| * CMC SG RAM Data Port |
| */ |
| register CCSGRAM { |
| address 0x0B0 |
| access_mode RW |
| modes M_DFF0, M_DFF1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * CMC SCB RAM Data Port |
| */ |
| register CCSCBRAM { |
| address 0x0B0 |
| access_mode RW |
| modes M_CCHAN |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Flex DMA Address. |
| */ |
| register FLEXADR { |
| address 0x0B0 |
| access_mode RW |
| size 3 |
| modes M_SCSI |
| } |
| |
| /* |
| * Flex DMA Byte Count |
| */ |
| register FLEXCNT { |
| address 0x0B3 |
| access_mode RW |
| size 2 |
| modes M_SCSI |
| } |
| |
| /* |
| * Flex DMA Status |
| */ |
| register FLEXDMASTAT { |
| address 0x0B5 |
| access_mode RW |
| modes M_SCSI |
| field FLEXDMAERR 0x02 |
| field FLEXDMADONE 0x01 |
| } |
| |
| /* |
| * Flex DMA Data Port |
| */ |
| register FLEXDATA { |
| address 0x0B6 |
| access_mode RW |
| modes M_SCSI |
| } |
| |
| /* |
| * Board Data |
| */ |
| register BRDDAT { |
| address 0x0B8 |
| access_mode RW |
| modes M_SCSI |
| count 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Board Control |
| */ |
| register BRDCTL { |
| address 0x0B9 |
| access_mode RW |
| modes M_SCSI |
| count 7 |
| field FLXARBACK 0x80 |
| field FLXARBREQ 0x40 |
| field BRDADDR 0x38 |
| field BRDEN 0x04 |
| field BRDRW 0x02 |
| field BRDSTB 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Serial EEPROM Address |
| */ |
| register SEEADR { |
| address 0x0BA |
| access_mode RW |
| modes M_SCSI |
| count 4 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Serial EEPROM Data |
| */ |
| register SEEDAT { |
| address 0x0BC |
| access_mode RW |
| size 2 |
| modes M_SCSI |
| count 4 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Serial EEPROM Status |
| */ |
| register SEESTAT { |
| address 0x0BE |
| access_mode RO |
| modes M_SCSI |
| count 1 |
| field INIT_DONE 0x80 |
| field SEEOPCODE 0x70 |
| field LDALTID_L 0x08 |
| field SEEARBACK 0x04 |
| field SEEBUSY 0x02 |
| field SEESTART 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Serial EEPROM Control |
| */ |
| register SEECTL { |
| address 0x0BE |
| access_mode RW |
| modes M_SCSI |
| count 4 |
| field SEEOPCODE 0x70 { |
| SEEOP_ERASE 0x70, |
| SEEOP_READ 0x60, |
| SEEOP_WRITE 0x50, |
| /* |
| * The following four commands use special |
| * addresses for differentiation. |
| */ |
| SEEOP_ERAL 0x40 |
| } |
| mask SEEOP_EWEN 0x40 |
| mask SEEOP_WALL 0x40 |
| mask SEEOP_EWDS 0x40 |
| field SEERST 0x02 |
| field SEESTART 0x01 |
| dont_generate_debug_code |
| } |
| |
| const SEEOP_ERAL_ADDR 0x80 |
| const SEEOP_EWEN_ADDR 0xC0 |
| const SEEOP_WRAL_ADDR 0x40 |
| const SEEOP_EWDS_ADDR 0x00 |
| |
| /* |
| * SCB Counter |
| */ |
| register SCBCNT { |
| address 0x0BF |
| access_mode RW |
| modes M_SCSI |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Data FIFO Write Address |
| * Pointer to the next QWD location to be written to the data FIFO. |
| */ |
| register DFWADDR { |
| address 0x0C0 |
| access_mode RW |
| size 2 |
| modes M_DFF0, M_DFF1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * DSP Filter Control |
| */ |
| register DSPFLTRCTL { |
| address 0x0C0 |
| access_mode RW |
| modes M_CFG |
| field FLTRDISABLE 0x20 |
| field EDGESENSE 0x10 |
| field DSPFCNTSEL 0x0F |
| } |
| |
| /* |
| * DSP Data Channel Control |
| */ |
| register DSPDATACTL { |
| address 0x0C1 |
| access_mode RW |
| modes M_CFG |
| count 3 |
| field BYPASSENAB 0x80 |
| field DESQDIS 0x10 |
| field RCVROFFSTDIS 0x04 |
| field XMITOFFSTDIS 0x02 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Data FIFO Read Address |
| * Pointer to the next QWD location to be read from the data FIFO. |
| */ |
| register DFRADDR { |
| address 0x0C2 |
| access_mode RW |
| size 2 |
| modes M_DFF0, M_DFF1 |
| } |
| |
| /* |
| * DSP REQ Control |
| */ |
| register DSPREQCTL { |
| address 0x0C2 |
| access_mode RW |
| modes M_CFG |
| field MANREQCTL 0xC0 |
| field MANREQDLY 0x3F |
| } |
| |
| /* |
| * DSP ACK Control |
| */ |
| register DSPACKCTL { |
| address 0x0C3 |
| access_mode RW |
| modes M_CFG |
| field MANACKCTL 0xC0 |
| field MANACKDLY 0x3F |
| } |
| |
| /* |
| * Data FIFO Data |
| * Read/Write byte port into the data FIFO. The read and write |
| * FIFO pointers increment with each read and write respectively |
| * to this port. |
| */ |
| register DFDAT { |
| address 0x0C4 |
| access_mode RW |
| modes M_DFF0, M_DFF1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * DSP Channel Select |
| */ |
| register DSPSELECT { |
| address 0x0C4 |
| access_mode RW |
| modes M_CFG |
| count 1 |
| field AUTOINCEN 0x80 |
| field DSPSEL 0x1F |
| dont_generate_debug_code |
| } |
| |
| const NUMDSPS 0x14 |
| |
| /* |
| * Write Bias Control |
| */ |
| register WRTBIASCTL { |
| address 0x0C5 |
| access_mode WO |
| modes M_CFG |
| count 3 |
| field AUTOXBCDIS 0x80 |
| field XMITMANVAL 0x3F |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Currently the WRTBIASCTL is the same as the default. |
| */ |
| const WRTBIASCTL_HP_DEFAULT 0x0 |
| |
| /* |
| * Receiver Bias Control |
| */ |
| register RCVRBIOSCTL { |
| address 0x0C6 |
| access_mode WO |
| modes M_CFG |
| field AUTORBCDIS 0x80 |
| field RCVRMANVAL 0x3F |
| } |
| |
| /* |
| * Write Bias Calculator |
| */ |
| register WRTBIASCALC { |
| address 0x0C7 |
| access_mode RO |
| modes M_CFG |
| } |
| |
| /* |
| * Data FIFO Pointers |
| * Contains the byte offset from DFWADDR and DWRADDR to the current |
| * FIFO write/read locations. |
| */ |
| register DFPTRS { |
| address 0x0C8 |
| access_mode RW |
| modes M_DFF0, M_DFF1 |
| } |
| |
| /* |
| * Receiver Bias Calculator |
| */ |
| register RCVRBIASCALC { |
| address 0x0C8 |
| access_mode RO |
| modes M_CFG |
| } |
| |
| /* |
| * Data FIFO Backup Read Pointer |
| * Contains the data FIFO address to be restored if the last |
| * data accessed from the data FIFO was not transferred successfully. |
| */ |
| register DFBKPTR { |
| address 0x0C9 |
| access_mode RW |
| size 2 |
| modes M_DFF0, M_DFF1 |
| } |
| |
| /* |
| * Skew Calculator |
| */ |
| register SKEWCALC { |
| address 0x0C9 |
| access_mode RO |
| modes M_CFG |
| } |
| |
| /* |
| * Data FIFO Debug Control |
| */ |
| register DFDBCTL { |
| address 0x0CB |
| access_mode RW |
| modes M_DFF0, M_DFF1 |
| field DFF_CIO_WR_RDY 0x20 |
| field DFF_CIO_RD_RDY 0x10 |
| field DFF_DIR_ERR 0x08 |
| field DFF_RAMBIST_FAIL 0x04 |
| field DFF_RAMBIST_DONE 0x02 |
| field DFF_RAMBIST_EN 0x01 |
| } |
| |
| /* |
| * Data FIFO Space Count |
| * Number of FIFO locations that are free. |
| */ |
| register DFSCNT { |
| address 0x0CC |
| access_mode RO |
| size 2 |
| modes M_DFF0, M_DFF1 |
| } |
| |
| /* |
| * Data FIFO Byte Count |
| * Number of filled FIFO locations. |
| */ |
| register DFBCNT { |
| address 0x0CE |
| access_mode RO |
| size 2 |
| modes M_DFF0, M_DFF1 |
| } |
| |
| /* |
| * Sequencer Program Overlay Address. |
| * Low address must be written prior to high address. |
| */ |
| register OVLYADDR { |
| address 0x0D4 |
| modes M_SCSI |
| size 2 |
| access_mode RW |
| } |
| |
| /* |
| * Sequencer Control 0 |
| * Error detection mode, speed configuration, |
| * single step, breakpoints and program load. |
| */ |
| register SEQCTL0 { |
| address 0x0D6 |
| access_mode RW |
| count 11 |
| field PERRORDIS 0x80 |
| field PAUSEDIS 0x40 |
| field FAILDIS 0x20 |
| field FASTMODE 0x10 |
| field BRKADRINTEN 0x08 |
| field STEP 0x04 |
| field SEQRESET 0x02 |
| field LOADRAM 0x01 |
| } |
| |
| /* |
| * Sequencer Control 1 |
| * Instruction RAM Diagnostics |
| */ |
| register SEQCTL1 { |
| address 0x0D7 |
| access_mode RW |
| field OVRLAY_DATA_CHK 0x08 |
| field RAMBIST_DONE 0x04 |
| field RAMBIST_FAIL 0x02 |
| field RAMBIST_EN 0x01 |
| } |
| |
| /* |
| * Sequencer Flags |
| * Zero and Carry state of the ALU. |
| */ |
| register FLAGS { |
| address 0x0D8 |
| access_mode RO |
| count 23 |
| field ZERO 0x02 |
| field CARRY 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Sequencer Interrupt Control |
| */ |
| register SEQINTCTL { |
| address 0x0D9 |
| access_mode RW |
| field INTVEC1DSL 0x80 |
| field INT1_CONTEXT 0x20 |
| field SCS_SEQ_INT1M1 0x10 |
| field SCS_SEQ_INT1M0 0x08 |
| field INTMASK2 0x04 |
| field INTMASK1 0x02 |
| field IRET 0x01 |
| } |
| |
| /* |
| * Sequencer RAM Data Port |
| * Single byte window into the Sequencer Instruction Ram area starting |
| * at the address specified by OVLYADDR. To write a full instruction word, |
| * simply write four bytes in succession. OVLYADDR will increment after the |
| * most significant instrution byte (the byte with the parity bit) is written. |
| */ |
| register SEQRAM { |
| address 0x0DA |
| access_mode RW |
| count 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Sequencer Program Counter |
| * Low byte must be written prior to high byte. |
| */ |
| register PRGMCNT { |
| address 0x0DE |
| access_mode RW |
| size 2 |
| count 5 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Accumulator |
| */ |
| register ACCUM { |
| address 0x0E0 |
| access_mode RW |
| accumulator |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Source Index Register |
| * Incrementing index for reads of SINDIR and the destination (low byte only) |
| * for any immediate operands passed in jmp, jc, jnc, call instructions. |
| * Example: |
| * mvi 0xFF call some_routine; |
| * |
| * Will set SINDEX[0] to 0xFF and call the routine "some_routine. |
| */ |
| register SINDEX { |
| address 0x0E2 |
| access_mode RW |
| size 2 |
| sindex |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Destination Index Register |
| * Incrementing index for writes to DINDIR. Can be used as a scratch register. |
| */ |
| register DINDEX { |
| address 0x0E4 |
| access_mode RW |
| size 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Break Address |
| * Sequencer instruction breakpoint address address. |
| */ |
| register BRKADDR0 { |
| address 0x0E6 |
| access_mode RW |
| } |
| |
| register BRKADDR1 { |
| address 0x0E6 |
| access_mode RW |
| field BRKDIS 0x80 /* Disable Breakpoint */ |
| } |
| |
| /* |
| * All Ones |
| * All reads to this register return the value 0xFF. |
| */ |
| register ALLONES { |
| address 0x0E8 |
| access_mode RO |
| allones |
| dont_generate_debug_code |
| } |
| |
| /* |
| * All Zeros |
| * All reads to this register return the value 0. |
| */ |
| register ALLZEROS { |
| address 0x0EA |
| access_mode RO |
| allzeros |
| dont_generate_debug_code |
| } |
| |
| /* |
| * No Destination |
| * Writes to this register have no effect. |
| */ |
| register NONE { |
| address 0x0EA |
| access_mode WO |
| none |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Source Index Indirect |
| * Reading this register is equivalent to reading (register_base + SINDEX) and |
| * incrementing SINDEX by 1. |
| */ |
| register SINDIR { |
| address 0x0EC |
| access_mode RO |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Destination Index Indirect |
| * Writing this register is equivalent to writing to (register_base + DINDEX) |
| * and incrementing DINDEX by 1. |
| */ |
| register DINDIR { |
| address 0x0ED |
| access_mode WO |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Function One |
| * 2's complement to bit value conversion. Write the 2's complement value |
| * (0-7 only) to the top nibble and retrieve the bit indexed by that value |
| * on the next read of this register. |
| * Example: |
| * Write 0x60 |
| * Read 0x40 |
| */ |
| register FUNCTION1 { |
| address 0x0F0 |
| access_mode RW |
| } |
| |
| /* |
| * Stack |
| * Window into the stack. Each stack location is 10 bits wide reported |
| * low byte followed by high byte. There are 8 stack locations. |
| */ |
| register STACK { |
| address 0x0F2 |
| access_mode RW |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Interrupt Vector 1 Address |
| * Interrupt branch address for SCS SEQ_INT1 mode 0 and 1 interrupts. |
| */ |
| register INTVEC1_ADDR { |
| address 0x0F4 |
| access_mode RW |
| size 2 |
| modes M_CFG |
| count 1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Current Address |
| * Address of the SEQRAM instruction currently executing instruction. |
| */ |
| register CURADDR { |
| address 0x0F4 |
| access_mode RW |
| size 2 |
| modes M_SCSI |
| count 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Interrupt Vector 2 Address |
| * Interrupt branch address for HST_SEQ_INT2 interrupts. |
| */ |
| register INTVEC2_ADDR { |
| address 0x0F6 |
| access_mode RW |
| size 2 |
| modes M_CFG |
| count 1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Last Address |
| * Address of the SEQRAM instruction executed prior to the current instruction. |
| */ |
| register LASTADDR { |
| address 0x0F6 |
| access_mode RW |
| size 2 |
| modes M_SCSI |
| } |
| |
| register AHD_PCI_CONFIG_BASE { |
| address 0x100 |
| access_mode RW |
| size 256 |
| modes M_CFG |
| } |
| |
| /* ---------------------- Scratch RAM Offsets ------------------------- */ |
| scratch_ram { |
| /* Mode Specific */ |
| address 0x0A0 |
| size 8 |
| modes 0, 1, 2, 3 |
| REG0 { |
| size 2 |
| dont_generate_debug_code |
| } |
| REG1 { |
| size 2 |
| } |
| REG_ISR { |
| size 2 |
| dont_generate_debug_code |
| } |
| SG_STATE { |
| size 1 |
| field SEGS_AVAIL 0x01 |
| field LOADING_NEEDED 0x02 |
| field FETCH_INPROG 0x04 |
| } |
| /* |
| * Track whether the transfer byte count for |
| * the current data phase is odd. |
| */ |
| DATA_COUNT_ODD { |
| size 1 |
| } |
| } |
| |
| scratch_ram { |
| /* Mode Specific */ |
| address 0x0F8 |
| size 8 |
| modes 0, 1, 2, 3 |
| LONGJMP_ADDR { |
| size 2 |
| dont_generate_debug_code |
| } |
| ACCUM_SAVE { |
| size 1 |
| dont_generate_debug_code |
| } |
| } |
| |
| |
| scratch_ram { |
| address 0x100 |
| size 128 |
| modes 0, 1, 2, 3 |
| /* |
| * Per "other-id" execution queues. We use an array of |
| * tail pointers into lists of SCBs sorted by "other-id". |
| * The execution head pointer threads the head SCBs for |
| * each list. |
| */ |
| WAITING_SCB_TAILS { |
| size 32 |
| dont_generate_debug_code |
| } |
| WAITING_TID_HEAD { |
| size 2 |
| dont_generate_debug_code |
| } |
| WAITING_TID_TAIL { |
| size 2 |
| dont_generate_debug_code |
| } |
| /* |
| * SCBID of the next SCB in the new SCB queue. |
| */ |
| NEXT_QUEUED_SCB_ADDR { |
| size 4 |
| dont_generate_debug_code |
| } |
| /* |
| * head of list of SCBs that have |
| * completed but have not been |
| * put into the qoutfifo. |
| */ |
| COMPLETE_SCB_HEAD { |
| size 2 |
| dont_generate_debug_code |
| } |
| /* |
| * The list of completed SCBs in |
| * the active DMA. |
| */ |
| COMPLETE_SCB_DMAINPROG_HEAD { |
| size 2 |
| dont_generate_debug_code |
| } |
| /* |
| * head of list of SCBs that have |
| * completed but need to be uploaded |
| * to the host prior to being completed. |
| */ |
| COMPLETE_DMA_SCB_HEAD { |
| size 2 |
| dont_generate_debug_code |
| } |
| /* |
| * tail of list of SCBs that have |
| * completed but need to be uploaded |
| * to the host prior to being completed. |
| */ |
| COMPLETE_DMA_SCB_TAIL { |
| size 2 |
| dont_generate_debug_code |
| } |
| /* |
| * head of list of SCBs that have |
| * been uploaded to the host, but cannot |
| * be completed until the QFREEZE is in |
| * full effect (i.e. no selections pending). |
| */ |
| COMPLETE_ON_QFREEZE_HEAD { |
| size 2 |
| dont_generate_debug_code |
| } |
| /* |
| * Counting semaphore to prevent new select-outs |
| * The queue is frozen so long as the sequencer |
| * and kernel freeze counts differ. |
| */ |
| QFREEZE_COUNT { |
| size 2 |
| } |
| KERNEL_QFREEZE_COUNT { |
| size 2 |
| } |
| /* |
| * Mode to restore on legacy idle loop exit. |
| */ |
| SAVED_MODE { |
| size 1 |
| } |
| /* |
| * Single byte buffer used to designate the type or message |
| * to send to a target. |
| */ |
| MSG_OUT { |
| size 1 |
| dont_generate_debug_code |
| } |
| /* Parameters for DMA Logic */ |
| DMAPARAMS { |
| size 1 |
| count 8 |
| field PRELOADEN 0x80 |
| field WIDEODD 0x40 |
| field SCSIEN 0x20 |
| field SDMAEN 0x10 |
| field SDMAENACK 0x10 |
| field HDMAEN 0x08 |
| field HDMAENACK 0x08 |
| field DIRECTION 0x04 /* Set indicates PCI->SCSI */ |
| field FIFOFLUSH 0x02 |
| field FIFORESET 0x01 |
| dont_generate_debug_code |
| } |
| SEQ_FLAGS { |
| size 1 |
| field NOT_IDENTIFIED 0x80 |
| field NO_CDB_SENT 0x40 |
| field TARGET_CMD_IS_TAGGED 0x40 |
| field DPHASE 0x20 |
| /* Target flags */ |
| field TARG_CMD_PENDING 0x10 |
| field CMDPHASE_PENDING 0x08 |
| field DPHASE_PENDING 0x04 |
| field SPHASE_PENDING 0x02 |
| field NO_DISCONNECT 0x01 |
| } |
| /* |
| * Temporary storage for the |
| * target/channel/lun of a |
| * reconnecting target |
| */ |
| SAVED_SCSIID { |
| size 1 |
| dont_generate_debug_code |
| } |
| SAVED_LUN { |
| size 1 |
| dont_generate_debug_code |
| } |
| /* |
| * The last bus phase as seen by the sequencer. |
| */ |
| LASTPHASE { |
| size 1 |
| field CDI 0x80 |
| field IOI 0x40 |
| field MSGI 0x20 |
| field P_BUSFREE 0x01 |
| enum PHASE_MASK CDO|IOO|MSGO { |
| P_DATAOUT 0x0, |
| P_DATAIN IOO, |
| P_DATAOUT_DT P_DATAOUT|MSGO, |
| P_DATAIN_DT P_DATAIN|MSGO, |
| P_COMMAND CDO, |
| P_MESGOUT CDO|MSGO, |
| P_STATUS CDO|IOO, |
| P_MESGIN CDO|IOO|MSGO |
| } |
| } |
| /* |
| * Value to "or" into the SCBPTR[1] value to |
| * indicate that an entry in the QINFIFO is valid. |
| */ |
| QOUTFIFO_ENTRY_VALID_TAG { |
| size 1 |
| dont_generate_debug_code |
| } |
| /* |
| * Kernel and sequencer offsets into the queue of |
| * incoming target mode command descriptors. The |
| * queue is full when the KERNEL_TQINPOS == TQINPOS. |
| */ |
| KERNEL_TQINPOS { |
| size 1 |
| count 1 |
| dont_generate_debug_code |
| } |
| TQINPOS { |
| size 1 |
| count 8 |
| dont_generate_debug_code |
| } |
| /* |
| * Base address of our shared data with the kernel driver in host |
| * memory. This includes the qoutfifo and target mode |
| * incoming command queue. |
| */ |
| SHARED_DATA_ADDR { |
| size 4 |
| dont_generate_debug_code |
| } |
| /* |
| * Pointer to location in host memory for next |
| * position in the qoutfifo. |
| */ |
| QOUTFIFO_NEXT_ADDR { |
| size 4 |
| dont_generate_debug_code |
| } |
| ARG_1 { |
| size 1 |
| mask SEND_MSG 0x80 |
| mask SEND_SENSE 0x40 |
| mask SEND_REJ 0x20 |
| mask MSGOUT_PHASEMIS 0x10 |
| mask EXIT_MSG_LOOP 0x08 |
| mask CONT_MSG_LOOP_WRITE 0x04 |
| mask CONT_MSG_LOOP_READ 0x03 |
| mask CONT_MSG_LOOP_TARG 0x02 |
| alias RETURN_1 |
| dont_generate_debug_code |
| } |
| ARG_2 { |
| size 1 |
| count 1 |
| alias RETURN_2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Snapshot of MSG_OUT taken after each message is sent. |
| */ |
| LAST_MSG { |
| size 1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Sequences the kernel driver has okayed for us. This allows |
| * the driver to do things like prevent initiator or target |
| * operations. |
| */ |
| SCSISEQ_TEMPLATE { |
| size 1 |
| count 7 |
| field MANUALCTL 0x40 |
| field ENSELI 0x20 |
| field ENRSELI 0x10 |
| field MANUALP 0x0C |
| field ENAUTOATNP 0x02 |
| field ALTSTIM 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * The initiator specified tag for this target mode transaction. |
| */ |
| INITIATOR_TAG { |
| size 1 |
| count 1 |
| dont_generate_debug_code |
| } |
| |
| SEQ_FLAGS2 { |
| size 1 |
| field PENDING_MK_MESSAGE 0x01 |
| field TARGET_MSG_PENDING 0x02 |
| field SELECTOUT_QFROZEN 0x04 |
| } |
| |
| ALLOCFIFO_SCBPTR { |
| size 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * The maximum amount of time to wait, when interrupt coalescing |
| * is enabled, before issuing a CMDCMPLT interrupt for a completed |
| * command. |
| */ |
| INT_COALESCING_TIMER { |
| size 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * The maximum number of commands to coalesce into a single interrupt. |
| * Actually the 2's complement of that value to simplify sequencer |
| * code. |
| */ |
| INT_COALESCING_MAXCMDS { |
| size 1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * The minimum number of commands still outstanding required |
| * to continue coalescing (2's complement of value). |
| */ |
| INT_COALESCING_MINCMDS { |
| size 1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Number of commands "in-flight". |
| */ |
| CMDS_PENDING { |
| size 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * The count of commands that have been coalesced. |
| */ |
| INT_COALESCING_CMDCOUNT { |
| size 1 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Since the HS_MAIBOX is self clearing, copy its contents to |
| * this position in scratch ram every time it changes. |
| */ |
| LOCAL_HS_MAILBOX { |
| size 1 |
| dont_generate_debug_code |
| } |
| /* |
| * Target-mode CDB type to CDB length table used |
| * in non-packetized operation. |
| */ |
| CMDSIZE_TABLE { |
| size 8 |
| count 8 |
| dont_generate_debug_code |
| } |
| /* |
| * When an SCB with the MK_MESSAGE flag is |
| * queued to the controller, it cannot enter |
| * the waiting for selection list until the |
| * selections for any previously queued |
| * commands to that target complete. During |
| * the wait, the MK_MESSAGE SCB is queued |
| * here. |
| */ |
| MK_MESSAGE_SCB { |
| size 2 |
| } |
| /* |
| * Saved SCSIID of MK_MESSAGE_SCB to avoid |
| * an extra SCBPTR operation when deciding |
| * if the MK_MESSAGE_SCB can be run. |
| */ |
| MK_MESSAGE_SCSIID { |
| size 1 |
| } |
| } |
| |
| /************************* Hardware SCB Definition ****************************/ |
| scb { |
| address 0x180 |
| size 64 |
| modes 0, 1, 2, 3 |
| SCB_RESIDUAL_DATACNT { |
| size 4 |
| alias SCB_CDB_STORE |
| alias SCB_HOST_CDB_PTR |
| dont_generate_debug_code |
| } |
| SCB_RESIDUAL_SGPTR { |
| size 4 |
| field SG_ADDR_MASK 0xf8 /* In the last byte */ |
| field SG_OVERRUN_RESID 0x02 /* In the first byte */ |
| field SG_LIST_NULL 0x01 /* In the first byte */ |
| dont_generate_debug_code |
| } |
| SCB_SCSI_STATUS { |
| size 1 |
| alias SCB_HOST_CDB_LEN |
| dont_generate_debug_code |
| } |
| SCB_TARGET_PHASES { |
| size 1 |
| dont_generate_debug_code |
| } |
| SCB_TARGET_DATA_DIR { |
| size 1 |
| dont_generate_debug_code |
| } |
| SCB_TARGET_ITAG { |
| size 1 |
| dont_generate_debug_code |
| } |
| SCB_SENSE_BUSADDR { |
| /* |
| * Only valid if CDB length is less than 13 bytes or |
| * we are using a CDB pointer. Otherwise contains |
| * the last 4 bytes of embedded cdb information. |
| */ |
| size 4 |
| alias SCB_NEXT_COMPLETE |
| dont_generate_debug_code |
| } |
| SCB_TAG { |
| alias SCB_FIFO_USE_COUNT |
| size 2 |
| dont_generate_debug_code |
| } |
| SCB_CONTROL { |
| size 1 |
| field TARGET_SCB 0x80 |
| field DISCENB 0x40 |
| field TAG_ENB 0x20 |
| field MK_MESSAGE 0x10 |
| field STATUS_RCVD 0x08 |
| field DISCONNECTED 0x04 |
| field SCB_TAG_TYPE 0x03 |
| } |
| SCB_SCSIID { |
| size 1 |
| field TID 0xF0 |
| field OID 0x0F |
| } |
| SCB_LUN { |
| size 1 |
| field LID 0xff |
| dont_generate_debug_code |
| } |
| SCB_TASK_ATTRIBUTE { |
| size 1 |
| /* |
| * Overloaded field for non-packetized |
| * ignore wide residue message handling. |
| */ |
| field SCB_XFERLEN_ODD 0x01 |
| dont_generate_debug_code |
| } |
| SCB_CDB_LEN { |
| size 1 |
| field SCB_CDB_LEN_PTR 0x80 /* CDB in host memory */ |
| dont_generate_debug_code |
| } |
| SCB_TASK_MANAGEMENT { |
| size 1 |
| dont_generate_debug_code |
| } |
| SCB_DATAPTR { |
| size 8 |
| dont_generate_debug_code |
| } |
| SCB_DATACNT { |
| /* |
| * The last byte is really the high address bits for |
| * the data address. |
| */ |
| size 4 |
| field SG_LAST_SEG 0x80 /* In the fourth byte */ |
| field SG_HIGH_ADDR_BITS 0x7F /* In the fourth byte */ |
| dont_generate_debug_code |
| } |
| SCB_SGPTR { |
| size 4 |
| field SG_STATUS_VALID 0x04 /* In the first byte */ |
| field SG_FULL_RESID 0x02 /* In the first byte */ |
| field SG_LIST_NULL 0x01 /* In the first byte */ |
| dont_generate_debug_code |
| } |
| SCB_BUSADDR { |
| size 4 |
| dont_generate_debug_code |
| } |
| SCB_NEXT { |
| alias SCB_NEXT_SCB_BUSADDR |
| size 2 |
| dont_generate_debug_code |
| } |
| SCB_NEXT2 { |
| size 2 |
| dont_generate_debug_code |
| } |
| SCB_SPARE { |
| size 8 |
| alias SCB_PKT_LUN |
| } |
| SCB_DISCONNECTED_LISTS { |
| size 8 |
| dont_generate_debug_code |
| } |
| } |
| |
| /*********************************** Constants ********************************/ |
| const MK_MESSAGE_BIT_OFFSET 4 |
| const TID_SHIFT 4 |
| const TARGET_CMD_CMPLT 0xfe |
| const INVALID_ADDR 0x80 |
| #define SCB_LIST_NULL 0xff |
| #define QOUTFIFO_ENTRY_VALID_TOGGLE 0x80 |
| |
| const CCSGADDR_MAX 0x80 |
| const CCSCBADDR_MAX 0x80 |
| const CCSGRAM_MAXSEGS 16 |
| |
| /* Selection Timeout Timer Constants */ |
| const STIMESEL_SHIFT 3 |
| const STIMESEL_MIN 0x18 |
| const STIMESEL_BUG_ADJ 0x8 |
| |
| /* WDTR Message values */ |
| const BUS_8_BIT 0x00 |
| const BUS_16_BIT 0x01 |
| const BUS_32_BIT 0x02 |
| |
| /* Offset maximums */ |
| const MAX_OFFSET 0xfe |
| const MAX_OFFSET_PACED 0xfe |
| const MAX_OFFSET_PACED_BUG 0x7f |
| /* |
| * Some 160 devices incorrectly accept 0xfe as a |
| * sync offset, but will overrun this value. Limit |
| * to 0x7f for speed lower than U320 which will |
| * avoid the persistent sync offset overruns. |
| */ |
| const MAX_OFFSET_NON_PACED 0x7f |
| const HOST_MSG 0xff |
| |
| /* |
| * The size of our sense buffers. |
| * Sense buffer mapping can be handled in either of two ways. |
| * The first is to allocate a dmamap for each transaction. |
| * Depending on the architecture, dmamaps can be costly. The |
| * alternative is to statically map the buffers in much the same |
| * way we handle our scatter gather lists. The driver implements |
| * the later. |
| */ |
| const AHD_SENSE_BUFSIZE 256 |
| |
| /* Target mode command processing constants */ |
| const CMD_GROUP_CODE_SHIFT 0x05 |
| |
| const STATUS_BUSY 0x08 |
| const STATUS_QUEUE_FULL 0x28 |
| const STATUS_PKT_SENSE 0xFF |
| const TARGET_DATA_IN 1 |
| |
| const SCB_TRANSFER_SIZE_FULL_LUN 56 |
| const SCB_TRANSFER_SIZE_1BYTE_LUN 48 |
| /* PKT_OVERRUN_BUFSIZE must be a multiple of 256 less than 64K */ |
| const PKT_OVERRUN_BUFSIZE 512 |
| |
| /* |
| * Timer parameters. |
| */ |
| const AHD_TIMER_US_PER_TICK 25 |
| const AHD_TIMER_MAX_TICKS 0xFFFF |
| const AHD_TIMER_MAX_US (AHD_TIMER_MAX_TICKS * AHD_TIMER_US_PER_TICK) |
| |
| /* |
| * Downloaded (kernel inserted) constants |
| */ |
| const SG_PREFETCH_CNT download |
| const SG_PREFETCH_CNT_LIMIT download |
| const SG_PREFETCH_ALIGN_MASK download |
| const SG_PREFETCH_ADDR_MASK download |
| const SG_SIZEOF download |
| const PKT_OVERRUN_BUFOFFSET download |
| const SCB_TRANSFER_SIZE download |
| const CACHELINE_MASK download |
| |
| /* |
| * BIOS SCB offsets |
| */ |
|