Documentation/devicetree/bindings/brcmstb/pm.txt

** Broadcom STB Power Management

Broadcom STB power management involves several hardware components which are
documented here.

* Always-On control block (AON CTRL)

This hardware provides control registers for the "always-on" (even in low-power
modes) hardware, such as the Power Management State Machine (PMSM).

Required properties:
- compatible     : should contain "brcm,brcmstb-aon-ctrl"
- reg            : the register start and length for the AON CTRL block

Example:

aon-ctrl@f0410000 {
	compatible = "brcm,brcmstb-aon-ctrl";
	reg = <0xf0410000 0x400>;
};

* Memory controllers

A Broadcom STB SoC typically has a number of independent memory controllers,
each of which may have several associated hardware blocks, which are versioned
independently (control registers, DDR PHYs, etc.). One might consider
describing these controllers as a parent "memory controllers" block, which
contains N sub-nodes (one for each controller in the system), each of which is
associated with a number of hardware register resources (e.g., its PHY). See
the example device tree snippet below.

* MEMC (MEMory Controller)

Represents a single memory controller instance.

Required properties:
- compatible     : should contain "brcm,brcmstb-memc" and "simple-bus"

Should contain subnodes for any of the following relevant hardware resources:

* DDR PHY control

Control registers for this memory controller's DDR PHY.

Required properties:
- compatible     : should contain "brcm,brcmstb-ddr-phy-v225.1" or
                   "brcm,brcmstb-ddr-phy-v240.1"
- reg            : the DDR PHY register range

* DDR SHIMPHY

Control registers for this memory controller's DDR SHIMPHY.

Required properties:
- compatible     : should contain "brcm,brcmstb-ddr-shimphy-v1.0"
- reg            : the DDR SHIMPHY register range

* MEMC DDR control

Sequencer DRAM parameters and control registers. Used for Self-Refresh
Power-Down (SRPD), among other things.

Required properties:
- compatible     : should contain "brcm,brcmstb-memc-ddr"
- reg            : the MEMC DDR register range

Example:

memory_controllers {
	ranges;
	compatible = "simple-bus";

	memc@0 {
		compatible = "brcm,brcmstb-memc", "simple-bus";
		ranges;

		ddr-phy@f1106000 {
			compatible = "brcm,brcmstb-ddr-phy-v240.1";
			reg = <0xf1106000 0x21c>;
		};

		shimphy@f1108000 {
			compatible = "brcm,brcmstb-ddr-shimphy-v1.0";
			reg = <0xf1108000 0xe4>;
		};

		memc-ddr@f1102000 {
			reg = <0xf1102000 0x800>;
			compatible = "brcm,brcmstb-memc-ddr";
		};
	};

	memc@1 {
		compatible = "brcm,brcmstb-memc", "simple-bus";
		ranges;

		ddr-phy@f1186000 {
			compatible = "brcm,brcmstb-ddr-phy-v240.1";
			reg = <0xf1186000 0x21c>;
		};

		shimphy@f1188000 {
			compatible = "brcm,brcmstb-ddr-shimphy-v1.0";
			reg = <0xf1188000 0xe4>;
		};

		memc-ddr@f1182000 {
			reg = <0xf1182000 0x800>;
			compatible = "brcm,brcmstb-memc-ddr";
		};
	};

	memc@2 {
		compatible = "brcm,brcmstb-memc", "simple-bus";
		ranges;

		ddr-phy@f1206000 {
			compatible = "brcm,brcmstb-ddr-phy-v240.1";
			reg = <0xf1206000 0x21c>;
		};

		shimphy@f1208000 {
			compatible = "brcm,brcmstb-ddr-shimphy-v1.0";
			reg = <0xf1208000 0xe4>;
		};

		memc-ddr@f1202000 {
			reg = <0xf1202000 0x800>;
			compatible = "brcm,brcmstb-memc-ddr";
		};
	};
};