#
# PINCTRL infrastructure and drivers
#

config PINCTRL
	bool

if PINCTRL

menu "Pin controllers"
	depends on PINCTRL

config PINMUX
	bool "Support pin multiplexing controllers" if COMPILE_TEST

config PINCONF
	bool "Support pin configuration controllers" if COMPILE_TEST

config GENERIC_PINCONF
	bool
	select PINCONF

config DEBUG_PINCTRL
	bool "Debug PINCTRL calls"
	depends on DEBUG_KERNEL
	help
	  Say Y here to add some extra checks and diagnostics to PINCTRL calls.

config PINCTRL_ADI2
	bool "ADI pin controller driver"
	depends on BLACKFIN
	select PINMUX
	select IRQ_DOMAIN
	help
	  This is the pin controller and gpio driver for ADI BF54x, BF60x and
	  future processors. This option is selected automatically when specific
	  machine and arch are selected to build.

config PINCTRL_AS3722
	bool "Pinctrl and GPIO driver for ams AS3722 PMIC"
	depends on MFD_AS3722 && GPIOLIB
	select PINMUX
	select GENERIC_PINCONF
	help
	  AS3722 device supports the configuration of GPIO pins for different
	  functionality. This driver supports the pinmux, push-pull and
	  open drain configuration for the GPIO pins of AS3722 devices. It also
	  supports the GPIO functionality through gpiolib.

config PINCTRL_BF54x
	def_bool y if BF54x
	select PINCTRL_ADI2

config PINCTRL_BF60x
	def_bool y if BF60x
	select PINCTRL_ADI2

config PINCTRL_AT91
	bool "AT91 pinctrl driver"
	depends on OF
	depends on ARCH_AT91
	select PINMUX
	select PINCONF
	select GPIOLIB
	select OF_GPIO
	select GPIOLIB_IRQCHIP
	help
	  Say Y here to enable the at91 pinctrl driver

config PINCTRL_BCM2835
	bool
	select PINMUX
	select PINCONF

config PINCTRL_BCM281XX
	bool "Broadcom BCM281xx pinctrl driver"
	depends on OF && (ARCH_BCM_MOBILE || COMPILE_TEST)
	select PINMUX
	select PINCONF
	select GENERIC_PINCONF
	select REGMAP_MMIO
	help
	  Say Y here to support Broadcom BCM281xx pinctrl driver, which is used
	  for the BCM281xx SoC family, including BCM11130, BCM11140, BCM11351,
	  BCM28145, and BCM28155 SoCs.  This driver requires the pinctrl
	  framework.  GPIO is provided by a separate GPIO driver.

config PINCTRL_LANTIQ
	bool
	depends on LANTIQ
	select PINMUX
	select PINCONF

config PINCTRL_FALCON
	bool
	depends on SOC_FALCON
	depends on PINCTRL_LANTIQ

config PINCTRL_ROCKCHIP
	bool
	select PINMUX
	select GENERIC_PINCONF
	select GENERIC_IRQ_CHIP
	select MFD_SYSCON

config PINCTRL_SINGLE
	tristate "One-register-per-pin type device tree based pinctrl driver"
	depends on OF
	select PINMUX
	select PINCONF
	select GENERIC_PINCONF
	help
	  This selects the device tree based generic pinctrl driver.

config PINCTRL_SIRF
	bool "CSR SiRFprimaII/SiRFmarco pin controller driver"
	depends on ARCH_SIRF
	select PINMUX
	select GPIOLIB_IRQCHIP

config PINCTRL_ST
	bool
	depends on OF
	select PINMUX
	select PINCONF
	select GPIOLIB_IRQCHIP

config PINCTRL_TEGRA
	bool
	select PINMUX
	select PINCONF

config PINCTRL_TEGRA20
	bool
	select PINCTRL_TEGRA

config PINCTRL_TEGRA30
	bool
	select PINCTRL_TEGRA

config PINCTRL_TEGRA114
	bool
	select PINCTRL_TEGRA

config PINCTRL_TEGRA124
	bool
	select PINCTRL_TEGRA

config PINCTRL_TEGRA_XUSB
	def_bool y if ARCH_TEGRA
	select GENERIC_PHY
	select PINCONF
	select PINMUX

config PINCTRL_TZ1090
	bool "Toumaz Xenif TZ1090 pin control driver"
	depends on SOC_TZ1090
	select PINMUX
	select GENERIC_PINCONF

config PINCTRL_TZ1090_PDC
	bool "Toumaz Xenif TZ1090 PDC pin control driver"
	depends on SOC_TZ1090
	select PINMUX
	select PINCONF

config PINCTRL_U300
	bool "U300 pin controller driver"
	depends on ARCH_U300
	select PINMUX
	select GENERIC_PINCONF

config PINCTRL_COH901
	bool "ST-Ericsson U300 COH 901 335/571 GPIO"
	depends on GPIOLIB && ARCH_U300 && PINCTRL_U300
	select GPIOLIB_IRQCHIP
	help
	  Say yes here to support GPIO interface on ST-Ericsson U300.
	  The names of the two IP block variants supported are
	  COH 901 335 and COH 901 571/3. They contain 3, 5 or 7
	  ports of 8 GPIO pins each.

config PINCTRL_PALMAS
	bool "Pinctrl driver for the PALMAS Series MFD devices"
	depends on OF && MFD_PALMAS
	select PINMUX
	select GENERIC_PINCONF
	help
	  Palmas device supports the configuration of pins for different
	  functionality. This driver supports the pinmux, push-pull and
	  open drain configuration for the Palmas series devices like
	  TPS65913, TPS80036 etc.

source "drivers/pinctrl/berlin/Kconfig"
source "drivers/pinctrl/freescale/Kconfig"
source "drivers/pinctrl/intel/Kconfig"
source "drivers/pinctrl/mvebu/Kconfig"
source "drivers/pinctrl/nomadik/Kconfig"
source "drivers/pinctrl/qcom/Kconfig"
source "drivers/pinctrl/samsung/Kconfig"
source "drivers/pinctrl/sh-pfc/Kconfig"
source "drivers/pinctrl/spear/Kconfig"
source "drivers/pinctrl/sunxi/Kconfig"
source "drivers/pinctrl/vt8500/Kconfig"

config PINCTRL_XWAY
	bool
	depends on SOC_TYPE_XWAY
	depends on PINCTRL_LANTIQ

config PINCTRL_TB10X
	bool
	depends on ARC_PLAT_TB10X

endmenu

endif