drivers/net/wireless/ipw2x00/Kconfig - kernel/bruno - Git at Google

 #
 # Intel Centrino wireless drivers
 #

 config IPW2100
 	tristate "Intel PRO/Wireless 2100 Network Connection"
 	depends on PCI && CFG80211
 	select WIRELESS_EXT
 	select WEXT_SPY
 	select WEXT_PRIV
 	select FW_LOADER
 	select LIB80211
 	select LIBIPW
 	---help---
           A driver for the Intel PRO/Wireless 2100 Network
 	  Connection 802.11b wireless network adapter.

           See <file:Documentation/networking/README.ipw2100> for information on
           the capabilities currently enabled in this driver and for tips
           for debugging issues and problems.

 	  In order to use this driver, you will need a firmware image for it.
           You can obtain the firmware from
 	  <http://ipw2100.sf.net/>.  Once you have the firmware image, you
 	  will need to place it in /lib/firmware.

           You will also very likely need the Wireless Tools in order to
           configure your card:

           <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.

           It is recommended that you compile this driver as a module (M)
           rather than built-in (Y). This driver requires firmware at device
           initialization time, and when built-in this typically happens
           before the filesystem is accessible (hence firmware will be
           unavailable and initialization will fail). If you do choose to build
           this driver into your kernel image, you can avoid this problem by
           including the firmware and a firmware loader in an initramfs.

 config IPW2100_MONITOR
         bool "Enable promiscuous mode"
         depends on IPW2100
         ---help---
 	  Enables promiscuous/monitor mode support for the ipw2100 driver.
 	  With this feature compiled into the driver, you can switch to
 	  promiscuous mode via the Wireless Tool's Monitor mode.  While in this
 	  mode, no packets can be sent.

 config IPW2100_DEBUG
 	bool "Enable full debugging output in IPW2100 module."
 	depends on IPW2100
 	---help---
 	  This option will enable debug tracing output for the IPW2100.

 	  This will result in the kernel module being ~60k larger.  You can
 	  control which debug output is sent to the kernel log by setting the
 	  value in

 	  /sys/bus/pci/drivers/ipw2100/debug_level

 	  This entry will only exist if this option is enabled.

 	  If you are not trying to debug or develop the IPW2100 driver, you
 	  most likely want to say N here.

 config IPW2200
 	tristate "Intel PRO/Wireless 2200BG and 2915ABG Network Connection"
 	depends on PCI && CFG80211
 	select CFG80211_WEXT_EXPORT
 	select WIRELESS_EXT
 	select WEXT_SPY
 	select WEXT_PRIV
 	select FW_LOADER
 	select LIB80211
 	select LIBIPW
 	---help---
           A driver for the Intel PRO/Wireless 2200BG and 2915ABG Network
 	  Connection adapters.

           See <file:Documentation/networking/README.ipw2200> for
 	  information on the capabilities currently enabled in this
 	  driver and for tips for debugging issues and problems.

 	  In order to use this driver, you will need a firmware image for it.
           You can obtain the firmware from
 	  <http://ipw2200.sf.net/>.  See the above referenced README.ipw2200
 	  for information on where to install the firmware images.

           You will also very likely need the Wireless Tools in order to
           configure your card:

           <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.

           It is recommended that you compile this driver as a module (M)
           rather than built-in (Y). This driver requires firmware at device
           initialization time, and when built-in this typically happens
           before the filesystem is accessible (hence firmware will be
           unavailable and initialization will fail). If you do choose to build
           this driver into your kernel image, you can avoid this problem by
           including the firmware and a firmware loader in an initramfs.

 config IPW2200_MONITOR
         bool "Enable promiscuous mode"
         depends on IPW2200
         ---help---
 	  Enables promiscuous/monitor mode support for the ipw2200 driver.
 	  With this feature compiled into the driver, you can switch to
 	  promiscuous mode via the Wireless Tool's Monitor mode.  While in this
 	  mode, no packets can be sent.

 config IPW2200_RADIOTAP
 	bool "Enable radiotap format 802.11 raw packet support"
 	depends on IPW2200_MONITOR

 config IPW2200_PROMISCUOUS
 	bool "Enable creation of a RF radiotap promiscuous interface"
 	depends on IPW2200_MONITOR
 	select IPW2200_RADIOTAP
 	---help---
           Enables the creation of a second interface prefixed 'rtap'.
           This second interface will provide every received in radiotap
 	  format.

           This is useful for performing wireless network analysis while
           maintaining an active association.

           Example usage:

             % modprobe ipw2200 rtap_iface=1
             % ifconfig rtap0 up
             % tethereal -i rtap0

           If you do not specify 'rtap_iface=1' as a module parameter then
           the rtap interface will not be created and you will need to turn
           it on via sysfs:

             % echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface

 config IPW2200_QOS
         bool "Enable QoS support"
         depends on IPW2200

 config IPW2200_DEBUG
 	bool "Enable full debugging output in IPW2200 module."
 	depends on IPW2200
 	---help---
 	  This option will enable low level debug tracing output for IPW2200.

 	  Note, normal debug code is already compiled in. This low level
 	  debug option enables debug on hot paths (e.g Tx, Rx, ISR) and
 	  will result in the kernel module being ~70 larger.  Most users
 	  will typically not need this high verbosity debug information.

 	  If you are not sure, say N here.

 config LIBIPW
 	tristate
 	depends on PCI && CFG80211
 	select WIRELESS_EXT
 	select WEXT_SPY
 	select CRYPTO
 	select CRYPTO_ARC4
 	select CRYPTO_ECB
 	select CRYPTO_AES
 	select CRYPTO_MICHAEL_MIC
 	select CRYPTO_ECB
 	select CRC32
 	select LIB80211
 	select LIB80211_CRYPT_WEP
 	select LIB80211_CRYPT_TKIP
 	select LIB80211_CRYPT_CCMP
 	---help---
 	This option enables the hardware independent IEEE 802.11
 	networking stack.  This component is deprecated in favor of the
 	mac80211 component.

 config LIBIPW_DEBUG
 	bool "Full debugging output for the LIBIPW component"
 	depends on LIBIPW
 	---help---
 	  This option will enable debug tracing output for the
 	  libipw component.

 	  This will result in the kernel module being ~70k larger.  You
 	  can control which debug output is sent to the kernel log by
 	  setting the value in

 	  /proc/net/ieee80211/debug_level

 	  For example:

 	  % echo 0x00000FFO > /proc/net/ieee80211/debug_level

 	  For a list of values you can assign to debug_level, you
 	  can look at the bit mask values in ieee80211.h

 	  If you are not trying to debug or develop the libipw
 	  component, you most likely want to say N here.
	#
	# Intel Centrino wireless drivers
	#

	config IPW2100
	tristate "Intel PRO/Wireless 2100 Network Connection"
	depends on PCI && CFG80211
	select WIRELESS_EXT
	select WEXT_SPY
	select WEXT_PRIV
	select FW_LOADER
	select LIB80211
	select LIBIPW
	---help---
	A driver for the Intel PRO/Wireless 2100 Network
	Connection 802.11b wireless network adapter.

	See <file:Documentation/networking/README.ipw2100> for information on
	the capabilities currently enabled in this driver and for tips
	for debugging issues and problems.

	In order to use this driver, you will need a firmware image for it.
	You can obtain the firmware from
	<http://ipw2100.sf.net/>. Once you have the firmware image, you
	will need to place it in /lib/firmware.

	You will also very likely need the Wireless Tools in order to
	configure your card:

	<http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.

	It is recommended that you compile this driver as a module (M)
	rather than built-in (Y). This driver requires firmware at device
	initialization time, and when built-in this typically happens
	before the filesystem is accessible (hence firmware will be
	unavailable and initialization will fail). If you do choose to build
	this driver into your kernel image, you can avoid this problem by
	including the firmware and a firmware loader in an initramfs.

	config IPW2100_MONITOR
	bool "Enable promiscuous mode"
	depends on IPW2100
	---help---
	Enables promiscuous/monitor mode support for the ipw2100 driver.
	With this feature compiled into the driver, you can switch to
	promiscuous mode via the Wireless Tool's Monitor mode. While in this
	mode, no packets can be sent.

	config IPW2100_DEBUG
	bool "Enable full debugging output in IPW2100 module."
	depends on IPW2100
	---help---
	This option will enable debug tracing output for the IPW2100.

	This will result in the kernel module being ~60k larger. You can
	control which debug output is sent to the kernel log by setting the
	value in

	/sys/bus/pci/drivers/ipw2100/debug_level

	This entry will only exist if this option is enabled.

	If you are not trying to debug or develop the IPW2100 driver, you
	most likely want to say N here.

	config IPW2200
	tristate "Intel PRO/Wireless 2200BG and 2915ABG Network Connection"
	depends on PCI && CFG80211
	select CFG80211_WEXT_EXPORT
	select WIRELESS_EXT
	select WEXT_SPY
	select WEXT_PRIV
	select FW_LOADER
	select LIB80211
	select LIBIPW
	---help---
	A driver for the Intel PRO/Wireless 2200BG and 2915ABG Network
	Connection adapters.

	See <file:Documentation/networking/README.ipw2200> for
	information on the capabilities currently enabled in this
	driver and for tips for debugging issues and problems.

	In order to use this driver, you will need a firmware image for it.
	You can obtain the firmware from
	<http://ipw2200.sf.net/>. See the above referenced README.ipw2200
	for information on where to install the firmware images.

	You will also very likely need the Wireless Tools in order to
	configure your card:

	<http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.

	It is recommended that you compile this driver as a module (M)
	rather than built-in (Y). This driver requires firmware at device
	initialization time, and when built-in this typically happens
	before the filesystem is accessible (hence firmware will be
	unavailable and initialization will fail). If you do choose to build
	this driver into your kernel image, you can avoid this problem by
	including the firmware and a firmware loader in an initramfs.

	config IPW2200_MONITOR
	bool "Enable promiscuous mode"
	depends on IPW2200
	---help---
	Enables promiscuous/monitor mode support for the ipw2200 driver.
	With this feature compiled into the driver, you can switch to
	promiscuous mode via the Wireless Tool's Monitor mode. While in this
	mode, no packets can be sent.

	config IPW2200_RADIOTAP
	bool "Enable radiotap format 802.11 raw packet support"
	depends on IPW2200_MONITOR

	config IPW2200_PROMISCUOUS
	bool "Enable creation of a RF radiotap promiscuous interface"
	depends on IPW2200_MONITOR
	select IPW2200_RADIOTAP
	---help---
	Enables the creation of a second interface prefixed 'rtap'.
	This second interface will provide every received in radiotap
	format.

	This is useful for performing wireless network analysis while
	maintaining an active association.

	Example usage:

	% modprobe ipw2200 rtap_iface=1
	% ifconfig rtap0 up
	% tethereal -i rtap0

	If you do not specify 'rtap_iface=1' as a module parameter then
	the rtap interface will not be created and you will need to turn
	it on via sysfs:

	% echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface

	config IPW2200_QOS
	bool "Enable QoS support"
	depends on IPW2200

	config IPW2200_DEBUG
	bool "Enable full debugging output in IPW2200 module."
	depends on IPW2200
	---help---
	This option will enable low level debug tracing output for IPW2200.

	Note, normal debug code is already compiled in. This low level
	debug option enables debug on hot paths (e.g Tx, Rx, ISR) and
	will result in the kernel module being ~70 larger. Most users
	will typically not need this high verbosity debug information.

	If you are not sure, say N here.

	config LIBIPW
	tristate
	depends on PCI && CFG80211
	select WIRELESS_EXT
	select WEXT_SPY
	select CRYPTO
	select CRYPTO_ARC4
	select CRYPTO_ECB
	select CRYPTO_AES
	select CRYPTO_MICHAEL_MIC
	select CRYPTO_ECB
	select CRC32
	select LIB80211
	select LIB80211_CRYPT_WEP
	select LIB80211_CRYPT_TKIP
	select LIB80211_CRYPT_CCMP
	---help---
	This option enables the hardware independent IEEE 802.11
	networking stack. This component is deprecated in favor of the
	mac80211 component.

	config LIBIPW_DEBUG
	bool "Full debugging output for the LIBIPW component"
	depends on LIBIPW
	---help---
	This option will enable debug tracing output for the
	libipw component.

	This will result in the kernel module being ~70k larger. You
	can control which debug output is sent to the kernel log by
	setting the value in

	/proc/net/ieee80211/debug_level

	For example:

	% echo 0x00000FFO > /proc/net/ieee80211/debug_level

	For a list of values you can assign to debug_level, you
	can look at the bit mask values in ieee80211.h

	If you are not trying to debug or develop the libipw
	component, you most likely want to say N here.