blob: 5dd139e7792e122edd1235a61dd6c2a452594d58 [file] [log] [blame]
/*
* Copyright 2014 Hans de Goede <hdegoede@redhat.com>
*
* Hans de Goede <hdegoede@redhat.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public
* License along with this file; if not, write to the Free
* Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
* MA 02110-1301 USA
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun7i-a20.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "LeMaker Banana Pi";
compatible = "lemaker,bananapi", "allwinner,sun7i-a20";
aliases {
serial0 = &uart0;
serial1 = &uart3;
serial2 = &uart7;
};
soc@01c00000 {
spi0: spi@01c05000 {
pinctrl-names = "default";
pinctrl-0 = <&spi0_pins_a>;
status = "okay";
};
mmc0: mmc@01c0f000 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
cd-inverted;
status = "okay";
};
usbphy: phy@01c13400 {
usb1_vbus-supply = <&reg_usb1_vbus>;
usb2_vbus-supply = <&reg_usb2_vbus>;
status = "okay";
};
ehci0: usb@01c14000 {
status = "okay";
};
ohci0: usb@01c14400 {
status = "okay";
};
ahci: sata@01c18000 {
status = "okay";
};
ehci1: usb@01c1c000 {
status = "okay";
};
ohci1: usb@01c1c400 {
status = "okay";
};
pinctrl@01c20800 {
mmc0_cd_pin_bananapi: mmc0_cd_pin@0 {
allwinner,pins = "PH10";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
gmac_power_pin_bananapi: gmac_power_pin@0 {
allwinner,pins = "PH23";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
led_pins_bananapi: led_pins@0 {
allwinner,pins = "PH24";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
ir0: ir@01c21800 {
pinctrl-names = "default";
pinctrl-0 = <&ir0_pins_a>;
status = "okay";
};
uart0: serial@01c28000 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
uart3: serial@01c28c00 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins_b>;
status = "okay";
};
uart7: serial@01c29c00 {
pinctrl-names = "default";
pinctrl-0 = <&uart7_pins_a>;
status = "okay";
};
i2c0: i2c@01c2ac00 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
compatible = "x-powers,axp209";
reg = <0x34>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#interrupt-cells = <1>;
};
};
i2c2: i2c@01c2b400 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
gmac: ethernet@01c50000 {
pinctrl-names = "default";
pinctrl-0 = <&gmac_pins_rgmii_a>;
phy = <&phy1>;
phy-mode = "rgmii";
phy-supply = <&reg_gmac_3v3>;
status = "okay";
phy1: ethernet-phy@1 {
reg = <1>;
};
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pins_bananapi>;
green {
label = "bananapi:green:usr";
gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
};
};
reg_usb1_vbus: usb1-vbus {
status = "okay";
};
reg_usb2_vbus: usb2-vbus {
status = "okay";
};
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&gmac_power_pin_bananapi>;
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
startup-delay-us = <100000>;
enable-active-high;
gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>;
};
};